Ansible User Guide

OcNOS-DC : Ansible User Guide : Ansible User Guide

Ansible User Guide

Steps to use an Ansible Playbook

In the below example, we will show steps to use an Ansible Playbook using Jinja2 template and sample parameter file. This example show how to configure LDP protocol:

ocnos_ldp.j2

osboxes@osboxes:~/playbooks$ cat templates/ocnos_ldp.j2

{%if ldp is defined%}

router ldp

{% for peer in ldp.peers -%}

targeted-peer ipv4 {{ peer.address }}

exit

{% endfor %}

{% if ldp.advertise_label_prefix is defined %}

advertise-labels for only_lo to any

{%endif%}

{% for interface in ldp.interfaces -%}

interface {{ interface.name }}

enable-ldp {{ interface.protocol }}

label-switching

exit

{% endfor %}

{%endif%}

We will provide the LDP configuration details in the appropriate host_vars file.

sw2.yml

osboxes@osboxes:~/playbooks$ cat host_vars/sw2.yml

ldp:

peers:

- address: 1.1.1.1

- address: 3.3.3.3

advertise_label_prefix: only_lo

ldp_interfaces:

- { ldp_interface: eth1, ldp_protocol: ipv4 }

- { ldp_interface: eth2, ldp_protocol: ipv4 }

Here is the overall directory structure of the Ansible Playbook and associated files.

osboxes@osboxes:~/playbooks$ tree

|___ansible.cfg

|___backup

|___group_vars

|___ocnos.yml

|___hosts-net

|___host_vars

|___sw2.yml

|___ldp-playbook.yml

|___showldp-playbook.yml

|___templates

|___ocnos_ldp.j2

The following is the content of ansible.cfg file which points to hosts-net inventory file.

ansible.cfg

osboxes@osboxes:~/playbooks$ cat ansible.cfg

[defaults]

inventory = hosts-net

host_key_checking = False

retry_files_enabled = False

interpreter_python = auto

osboxes@osboxes:~/playbooks

Following is the content of the hosts-net inventory file. Currently this has details of only one device.

hosts-net

osboxes@osboxes:~/playbooks$ cat hosts-net

[ocnos]

sw2 ansible_host=10.12.9.105

osboxes@osboxes:~/playbooks$

Following is the content of ocnos.yml in group_vars folder.

ocnos.yml

osboxes@osboxes:~/playbooks$ cat group_vars/ocnos.yml

ansible_connection: network_cli

ansible_network_os: ocnos

ansible_become: yes

ansible_become_method: enable

ansible_ssh_user: ocnos

ansible_ssh_pass: ocnos

osboxes@osboxes:

The below playbook pushes the ldp configuration created using the template file 'ocnos_ldp.j2' for all the ocnos hosts using the appropriate host_vars file 'sw2.yml':

ldp-playbook.yml

(ansible) osboxes@osboxes:~/playbooks$ cat ldp-playbook.yml

---

- hosts: ocnos

gather_facts: no

tasks:

- name: configure LDP config on OcNOS

cli_config:

config: "{{ lookup('template', 'templates/{{ ansible_network_os }}_ldp.j2') }}"

Configuration on the OcNOS device before executing the Ansible Playbook:

#show running-config ldp

Now we can execute the Ansible playbook and below are the logs that will be seen.

(ansible) osboxes@osboxes:~/playbooks$ ansible-playbook ldp-playbook.yml

PLAY [ocnos] ******************************************************************************************************

TASK [configure LDP config on OcNOS] ******************************************************************************

changed: [sw2]

PLAY RECAP ********************************************************************************************************

sw2 : ok=1 changed=1 unreachable=0 failed=0 skipped=0 rescued=0 ignored=0

Now check the configs on the OcNOS device. which should show the LDP configurations.

#show running-config ldp

router ldp

targeted-peer ipv4 1.1.1.1

exit-targeted-peer-mode

targeted-peer ipv4 3.3.3.3

exit-targeted-peer-mode

advertise-labels for only_lo to any

interface eth2

enable-ldp ipv4

interface eth1

enable-ldp ipv4

The below playbook shows how to check the runtime status of LDP protocol through the 'show ldp session' command and prints its output. It is assumed that the neighboring nodes are configured accordingly to get the LDP session up and running.

showldp-playbook.yml

osboxes@osboxes:~/playbooks$ cat showldp-playbook.yml

---

- hosts: ocnos

gather_facts: no

tasks:

- name: show LDP config ocnos

cli_command:

command: show ldp session

- name: debug

debug:

msg: "{{ result.stdout_lines }}"

osboxes@osboxes:~/playbooks$

When you run this playbook, the following will be its output. Parsing of the show command output needs to be done to determine if the runtime status of the protocol is fine.

(ansible) osboxes@osboxes:~/playbooks$ ansible-playbook showldp-playbook.yml

PLAY [ocnos] ******************************************************************************************************

TASK [show LDP config ocnos] **************************************************************************************

ok: [sw2]

TASK [debug] ******************************************************************************************************

ok: [sw2] => {

"msg": [

"Peer IP Address IF Name My Role State KeepAlive UpTime",

"3.3.3.3 eth2 Passive OPERATIONAL 30 03:58:20",

"1.1.1.1 eth1 Active OPERATIONAL 30 03:58:20"

]

}

PLAY RECAP ********************************************************************************************************

sw2 : ok=2 changed=0 unreachable=0 failed=0 skipped=0 rescued=0 ignored=0

(ansible) osboxes@osboxes:~/playbooks$

The below playbook is to unconfigure the LDP configuration on the OcNOS device.

osboxes@osboxes:~/playbooks$ cat unconfigureldp-playbook.yml

---

- hosts: ocnos

gather_facts: no

tasks:

- name: give "no router ldp" command

ipinfusion.ocnos.ocnos_config:

lines:

- no router ldp

- name: show LDP config ocnos

cli_command:

command: show running-config ldp

- name: debug

debug:

msg: "{{ result.stdout_lines }}"

Jinja2 Templates for configuring OcNOS

In this section, we will provide a few Jinja2 templates which can be used to configure a few protocols in OcNOS. Also a sample yaml parameter file is provided for each j2 template with explanations of the parameters. While creating the Jinja2 template, only the commonly used configuration is considered. Customers can use these templates as such, if it meets their configuration needs or can modify them accordingly.

Template File for LDP

ocnos_ldp.j2

{%if ldp is defined%}

router ldp

{% for peer in ldp.peers -%}

targeted-peer ipv4 {{ peer.address }}

exit

{% endfor %}

{% if ldp.advertise_label_prefix is defined %}

advertise-labels for only_lo to any

{%endif%}

{% for interface in ldp.interfaces -%}

interface {{ interface.name }}

enable-ldp {{ interface.protocol }}

label-switching

exit

{% endfor %}

{%endif%}

Sample Parameter File for LDP

sw2.yml

ldp:	Router LDP configurations
peers:	Peer Details
- address: 1.1.1.1	Configures the targeted-peer IPv4 address as <1.1.1.1> under router LDP
- address: 3.3.3.3	Configures the targeted-peer IPv4 address as <3.3.3.3> under router LDP
advertise_label_prefix: only_lo	If defined it will Configure the advertise label command for "ony_lo" prefix_list under router ldp
interfaces:	LDP Interface configurations
- interface: eth1	Enables LDP on interface <eth1> for protocol <ipv4>
protocol: ipv4	Enables LDP for ipv4 protocol under interface eth1

BGP Configuration

Template File for BGP

ocnos_bgp.j2

{%if bgp is defined%}

router bgp {{ bgp.asn }}

{% if bgp.router is defined %}

{%else%}

no bgp default ipv4-unicast

bgp log-neighbor-changes

no bgp inbound-route-filter

{% endif %}

{% for network in bgp.networks -%}

network {{ network.network_id }}

{%if network.network_id =='36.0.0.3/32'%}

max-paths ibgp 2

{%endif%}

{% endfor -%}

{% for neighbor in bgp.neighbors -%}

neighbor {{ neighbor.neighbor_id }} remote-as {{ neighbor.remoteas }}

neighbor {{ neighbor.neighbor_id }} {{ neighbor.detection }} bfd multihop

neighbor {{ neighbor.neighbor_id }} update-source {{ neighbor.updatesource }}

{% endfor %}

allocate-label all

{% for address_family in bgp.address_family -%}

{% if address_family.address_family_type == 'vpnv4' -%}

address-family {{ address_family.address_family_type }} unicast

{% endif %}

{% if address_family.address_family_type == 'labeled-unicast' -%}

address-family ipv4 {{ address_family.address_family_type }}

{% endif %}

{% if address_family.address_family_type == 'vrf' -%}

{% for vrf in address_family.vrfs -%}

address-family ipv4 {{address_family.address_family_type }} {{ vrf.vrf_name }}

{% if vrf.protocol is defined %}

redistribute {{vrf.protocol}}

{% endif %}

redistribute connected

exit-address-family

{% endfor %}

{% endif %}

{% if address_family.neighbors is defined %}

{% for neighbor in address_family.neighbors -%}

neighbor {{neighbor.neighbor_id}} activate

{% if neighbor.route_reflector_type is defined %}

neighbor {{neighbor.neighbor_id}} {{ neighbor.route_reflector_type }}

{% endif %}

{% if neighbor.next_hop_type is defined %}

neighbor {{ neighbor.neighbor_id}} {{ neighbor.next_hop_type }}

{% endif %}

{% endfor %}

exit-address-family

{% endif %}

{% endfor %}

{%endif%}

Parameter File for BGP

sw2.yml

bgp:	Router BGP configurations
asn: 65001	Autonomous system number
networks:	Network command
-network_id: 36.0.0.2/32	Configures the network IPv4 address as <36.0.0.2> under router BGP 65001

neighbors:	Neighbor command
- neighbor_id: 10.0.1.14	Identifies the neighbor
remoteas: 65001	configure remote-as 65001 for neighbor 10.0.1.14 command under router bgp
detection: fall-over	Configure detection type as <fall-over bfd multihop>
command under router bgp
updatesource: lo	Configure update-source lo> for <neighbor 36.0.0.1 > under router bgp
address_family:	Address-family configuration
- address_family_type: labeled-unicast	Address family type label-unicast will be configured under router bgp
neighbors:	Neighbor configuration under address family
- neighbor_id: 10.0.1.14	Activate neighbor 10.0.1.14 for address family label-unicast under bgp
next_hop_type: next-hop-self	If next_hop_type is defined then it will configure the neighbor 10.0.1.14 next-hop-self command will be configured for address-family label-unicast
route_reflector_type: route- reflector-client	If route_reflector_type is defined then neighbor 10.0.1.14 will be configured as route reflector client for address-family label-unicast
- address_family_type: vpnv4	Adress family type vpnv4 will be configured under router bgp
neighbors:	Neighbor configuration under address family
- neighbor_id: 10.0.1.14	Activate neighbor 10.0.1.14 for address family vpnv4 under bgp
route_reflector_type:route
-reflector-client	If route_reflector_type is defined then neighbor 10.0.1.14 will be configured as route reflector client for address-family vpnv4
- address_family_type: vrf	Adress family type vrf will be configured under router bgp
vrfs:	Multiple Vrf 's name will be define under this
- vrf_name: 1001	Address family type vrf with name <1001> will be configured under router bgp

RSVP Configuration

Template File for RSVP

ocnos_rsvp.j2

{%if rsvp is defined %}

router rsvp

{% if rsvp.rsvppath is defined %}

{% for path in rsvp.rsvppath -%}

rsvp-path {{ path.name }} mpls

{% for hop in path.hops -%}

{{ hop }} strict

{% endfor %}

{% endif %}

{% if rsvp.interfaces is defined %}

{% for interface in rsvp.interfaces -%}

interface {{ interface.name }}

{% endfor %}

{% endif %}

{% if rsvp.trunks is defined %}

{% for trunk in rsvp.trunks -%}

rsvp-trunk {{ trunk.name }} ipv4

{% if trunk.FRR_TYPE is defined %}

{% endif %}

primary path {{ trunk.primary_path }}

primary label-record

{% if trunk.secondary_path is defined %}

secondary path {{ trunk.secondary_path }}

{% endif %}

from {{trunk.ingress}}

to {{ trunk.egress }}

{% endfor %}

{% endif %}

{% if rsvp.bypass is defined %}

{% for bypass in rsvp.bypass -%}

rsvp-bypass {{ bypass.name }}

from {{bypass.ingress}}

to {{ bypass.egress }}

label-record

path {{ bypass.path }}

exit

{% endfor %}

{% endif %}

{%endif%}

Parameter File for RSVP

sw2.yml

rsvp:	Router RSVP configurations
trunks:	Rsvp trunk Details
- name: TO_AR-1	Configures the rsvp-trunk with name TO_AR-1
ingress: 36.0.0.2	Configures the starting point of the trunk as 36.0.0.2
egress: 10.0.1.14	Configures the end point of the trunk as 10.0.1.14
FRR: primary fast-reroute protection facility	Configures the FRR as FACILITY
FRR_TYPE: primary fast-reroute node-protection	Configure the type of FRR type as <node-protection>
primary_path: TO_AR-1	Configures the trunk with a primary path TO_AR-1
secondary_path: TO_AR-1_Sec	Configures the trunk with a secondary path TO_AR-1_Sec
bypass:	Bypass configuration
- name: TO_AR-1_BKUP	Configures the rsvp-bypass with name TO_AR-1_BKUP
ingress: 36.0.0.2	Configures the starting point of the bypass as 36.0.0.2
egress: 10.0.1.14	Configures the end point of the trunk as 10.0.1.14
path: TO_AR-1_BKUP	Configures the bypass with path TO_AR-1_BKUP
rsvppath:	Rsvp path configuration
- name: TO_AR-2_BKUP	Configures the RSVP path with name TO_AR-2_BKUP
hops:	Hops configuration under path TO_AR-2_BKUP
- 10.110.140.110	Configures 10.110.140.110 as a strict hop under rsvp-path TO_AR-2_BKUP
- 101.1.1.2	Configures 101.1.1.2 as a strict hop under rsvp-path TO_AR-2_BKUP
- 101.3.1.2	Configures 101.3.1.2 as a strict hop under rsvp-path TO_AR-2_BKUP
- 111.2.1.2	Configures 111.2.1.2 as a strict hop under rsvp-path TO_AR-2_BKUP
- 10.0.1.15	Configures 10.0.1.15 as a strict hop under rsvp-path TO_AR-2_BKUP
interfaces:	Interface configuration for rsvp
- name: xe1	Configures Interface xe1 command
command: enable-rsvp	Configures enable-rsvp command under interface xe1

QoS Configuration

Template File for QOS

ocnos_qos.j2

{%if QOS is defined %}

qos enable

qos statistics

{% for classmap in QOS.classmap -%}

{% if classmap.protocol == "dscp" %}

class-map {{ classmap.matchtype }} {{ classmap.name }}

match {{ classmap.protocol }} {{ classmap.dscptype }}

{% endif %}

{% if classmap.protocol == "queuing" %}

class-map {{ classmap.matchtype }} {{ classmap.protocol }} {{ classmap.que_name }}

match {{ classmap.classification }} {{ classmap.name }}

{% endif %}

{% if classmap.protocol == "vlan" %}

class-map {{ classmap.matchtype }} {{ classmap.name }}

match {{ classmap.protocol }} {{ classmap.dscptype }}

{% endif %}

{% endfor %}

{% for policymap in QOS.policymap -%}

{% if policymap.qos_name is defined %}

{% for param in policymap.params %}

{% if param.matchtype is defined %}

{%if param.val is defined %}

{% if param.val==1%}

policy-map {{ param.matchtype }} {{ param.protocol }} {{ policymap.qos_name }}

{% endif %}

class {{ param.name }}

{% if param.cosvalue is defined %}

set queue {{param.cosvalue}}

{% endif %}

exit

{% endfor %}

{% endif %}

{% if policymap.que_name is defined %}

{% for param in policymap.params %}

{%if param.val is defined %}

{%if param.val ==1 %}

policy-map {{ param.matchtype }} {{ param.protocol }} {{ policymap.que_name }}

{% endif %}

class type {{ param.protocol }} {{param.classmap_name}}

shape {{param.shape_rate}}

exit

{% endfor %}

{% endif %}

{% endfor %}

{% for interface in QOS.interfaces -%}

interface {{interface.name}}

{% for policy in interface.policy_type -%}

{% if policy.type == "qos" %}

service-policy type {{policy.type}} input {{policy.policy_name}}

{% endif %}

{% if policy.type == "queuing" %}

service-policy type {{policy.type}} output {{policy.policy_name}}

{% endif %}

{% endfor %}

{%endif%}

Parameter File for QOS

sw2.yml

QOS:	QOS configuration
classmap:	Class-map configuration
- matchtype: match-all	Configures the Logical-AND of all match statements under this class-map
name: DSCP-AF11	Specify a class-map name (Max Size 32)
protocol: dscp	Configures the protocol type dscp under class-mapp DSCP-AF11
dscptype: af11	Configures Match type of dscp as af11 under DSCP-AF1
- matchtype: match-all	Configures the Logical-AND of all match statements under this class-map
name: VLAN100	Specify a class-map name (Max Size 32)
protocol: vlan	Configure te protocol type vlan under class-map VLAN100
dscptype: 500	Configures the vlan id under the class-map VLAN100
- matchtype: type	Configures the type of match statements under this class-map
protocol: queuing	Configure the protocol as queuing
que_name: defaultq	Configure the class-map defaultq name for protocol queuing
classification: service-template	Configures the classification type as service-template under defaultq
name: vpws	Configures the name of the service-template
- matchtype: type	Configures the type of match statements under this class-map
protocol: queuing	Configure the protocol as queuing under class-map
que_name: matchall	Configure the class-map matchall name for protocol queuing
classification: vlan	Configures the classification type as vlan
name: 1001	Configures the if of the vlan as 1001
policymap:	Policymap configuration
- qos_name: ALL-VLANs	Configure the name of the policy-map as ALL-VLANs
params:	Configure the parameter for policy-map
- matchtype: type	Configures the type command for policy-map
protocol: qos	Configure the type of protocol as qos for policy-map
name: VLAN100	Configure the class name as VLAN100 under policy-map ALL-VLANs
val: 1	Define the occurrence of under the policy-map
- qos_name: DSCP-ALL	Configure the name of the policy-map as DSCP-ALL
params:	Configure the parameter for policy-map
- matchtype: type	Configures the type command for policy-map
protocol: qos	Configure the type of protocol as qos for policy-map
name: DSCP-AF11	Configure the class name as DSCP-AF11 under policy-map DSCP-ALL
cosvalue: 1	Configures the queue value to be taken for matched traffic
Under class DSCP-AF11
val:1	Define the occurrence of under the policy-map
- matchtype: type	Configures the type command for policy-map
protocol: qos	Configure the type of protocol as qos for policy-map
name: DSCP-AF12	Configure the class name as DSCP-AF12 under policy-map DSCP-ALL
cosvalue: 1	Configures the queue value to be taken for matched traffic
Under class DSCP-AF12
val:2	Define the occurrence of under the policy-map
- que_name: shaper	Configure the name of the queue as shaper
params:	Configure the parameter for policy-map
- matchtype: type	Configures the type command for policy-map
protocol: queuing	Configure the type of protocol as queuing for policy-map
name: DSCP-EF	Configure the class name as DSCP-EF under policy-map shaper
val: 1	Define the occurrence of under the policy-map
classmap_name: defaultq	Configures the class-map name defaultq
shape_rate: 10 gbps	Configures the shape rate as 10 gbps under under class DSCP-EF
interfaces:	Interface configuration
- name: eth3	Configure the interface eth3 command
policy_type:	Policy configuration under interface
- type: qos	Configures the service policy type as qos
policy_name: ALL-VLANs	Configures the input policy name as ALL-VLANs for policy-type qos
- type: queuing	Configures the service policy type as queuing
policy_name: shaper	Configures the output policy name as shaper for policy-type queuing

Timing (PTP) and Synchronization (SyncE) Configuration

Template File for PTP and SyncE

ocnos_ptp_synce.j2

{%if PTP_SYNCE is defined%}

synce

ptp clock profile g8275.1

number-ports {{ PTP_SYNCE.numberport}}

{% if PTP_SYNCE.ptp is defined %}

{% for ptp_params in PTP_SYNCE.ptp -%}

clock-port {{ ptp_params.clockport }}

{% if ptp_params.interface is defined %}

network-interface {{ptp_params.interface}}

{% endif %}

exit

{% endfor %}

{% endif %}

{% if PTP_SYNCE.interfaces is defined %}

{% for interface in PTP_SYNCE.interfaces -%}

interface {{ interface.name }}

synce

mode {{ interface.mode }}

{% if interface.inputsource is defined %}

input-source {{ interface.inputsource }}

{%endif%}

{% if interface.outputsource is defined %}

{%endif%}

{% if interface.waittorestore is defined %}

wait-to-restore {{ interface.waittorestore }}

{% endif %}

exit

{% endfor %}

{% endif %}

{%endif%}

Sample Parameter File for PTP and SyncE

sw2.yml

PTP_SYNCE:	PTP Synce configurations
numberport: 5	Configure the numpber-port value as 1 under ptp clock profile g8275.1
ptp:	Ptp configuration
- clockport: 1	Configure the clock-port value as 1 under ptp clock profile g8275.1
interface: xe19	Configures network-interface as xe19 under clock-port 1
interfaces:	Interface configurations
- name: xe4	configures interface xe4
mode: synchronous	Enables mode synchronous under synce
inputsource: 10	Configure input-source as 10 under interface if defined
outputsource: output-source	Configure output-source under interface if defined
Waittorestore: 1	Configure wait-to-restore as 1 under interface if defined

VPWS Configuration

Template File for VPWS

ocnos_vpws.j2

{% if VPWS.pseudowire is defined %}

{% for vpws in VPWS.pseudowire -%}

mpls l2-circuit {{ vpws.vc_name }} {{ vpws.vc_id }} {{ vpws.peer }}

{% endfor %}

{% for template in VPWS.service_template -%}

service-template {{ template.name}}

{% if template.vlan is defined %}

match outer-vlan {{ template.vlan }}

{% endif %}

{% if template.operation is defined %}

{% if template.operation == "pop" %}

rewrite ingress {{ template.operation }} outgoing-tpid {{ template.tpid }}

{% endif %}

{% if template.operation == "translate" %}

rewrite ingress {{ template.operation }} {{ template.translate_vlan }} outgoing-tpid {{template.tpid }}

{% endif %}

{% endfor %}

{% for interface in VPWS.interfaces -%}

interface {{ interface.name }}

switchport

{% for binding in interface.vpws_binding -%}

mpls-l2-circuit {{ binding.instance}} service-template {{binding.service_template}}

{% endfor %}

{% endif %}

Sample Parameter File for VPWS

sw2.yml

VPWS:	VPWS configurations
pseudowire:	Pseudowire(PW) instance configuration
- vc_name: vpws	Configures the name of PW as vpws
vc_id: 1	Configures the PW id as 1
peer: 36.0.0.8	Configures PW peer id as 36.0.0.8
- vc_name: vpws-2	Configures the name of PW as vpws-2
vc_id: 2	Configures the PW id as 2
peer: 10.0.1.14	Configures PW peer id as 10.0.1.14
service_template:	Service-template configuration
- name: vpws	Configure service-template name as vpws
vlan: 555	Configure match-outer vlan as vlan-id 555 under service-template vpws
operation: pop	Configure rewrite ingress operation as pop under service-template vpws
tpid: dot1.q	Configure outgoing tpid as dot1.q under service-template vpws
- name: vpws-2	Configure service-template name as vpws-2
vlan: 600	Configure match-outer vlan as vlan-id 600 under service-template vpws
interfaces:	Interface configuration
- name: xe20	Configure interface xe20 command
vpws_binding:	Configuration to bing vpws instance with service -template
- instance: vpws	Configure the binding of instance name vpws
service_template: vpws	Configure the vpws binding with service-template vpws under interface
- instance: vpws-2	Configure the binding of instance name vpws-2
service_template: vpws-2	Configure the vpws binding with service-template vpws -2 under interface

L3VPN Configuration

Template File for L3VPN

ocnos_l3vpn.j2

{% if L3VPN.vrfs is defined %}

{% for vrf in L3VPN.vrfs -%}

ip vrf {{ vrf.vrf_name }}

rd {{ vrf.rd_1 }}:{{ vrf.rd_2 }}

route-target both {{ vrf.rt_1 }}:{{ vrf.rt_2 }}

{% endfor %}

{% for interface in L3VPN.vrf_interfaces -%}

interface {{ interface.interface_name }}

ip vrf forwarding {{ interface.vrf_name }}

ip address {{ interface.address }}

{% endfor %}

{% endif %}

Sample Parameter File for L3VPN

sw2.yml

L3VPN:	L3VPN configurations
vrfs:	VRF instance configuration
- vrf_name: 1001	Configures the name of VRFas 1001
rd_1: 36.0.0.2	Configures the ASN or IP-address value depending on the ASN:nn_or_IP-address:nn route distinguisher value used .
rd_2: 1001	Configures the nn on the ASN:nn_or_IP-address:nn route distinguisher value.
rt_1: 65001	Configures the ASN or IP-address value depending on the ASN:nn_or_IP-address:nn format used for route-target
rt_2: 1001	Configure nn value of the route-target
vrf_interfaces:	Vrf interface configuration
- interface_name: eth2	Configure interface eth2
vrf_name: 1001	Configure the interface as part of the vrf 1001
address: 19.19.19.1/24	Configure the ip address 19.19.19.1/24on the vrf interface

Route Map Configuration

Template File for Route Map

ocnos_route_map.j2

{%if Route_Map is defined%}

{% for routemap in Route_Map.params -%}

route-map {{ routemap.name }} {{routemap.permission}} {{routemap.seq_no}}

{% if routemap.match=="address" %}

{{ routemap.operation}} {{ routemap.protocol }} {{ routemap.match }} prefix-list {{routemap.prefix_list}}

{%else%}

{%endif%}

{% endfor %}

{%endif%}

Sample Parameter File for Route Map

sw2.yml

Route_Map:	Route map configurations
params:	Route map parameters configuration
- name: NEXTHOP_SELF	Configures the name of the route_map
permission: permit	Configure the permission type as permit for route map
seq_no: 10	Configure the sequence no. as 10
operation: set	Configures the operation type under route-map as set
protocol: vpnv4	Configures the protocol as vpnv4
match: next-hop	Configures the match-type as next-hop under route-map NEXTHOP_SELF
prefix_list: 36.0.0.1	Configure the matching prefix as 36.0.0.1 .we can define prefix list name also if it is created .
- name: LO_RED_TO_0	Configures the name of the route_map
permission: permit	Configure the permission type as permit for route map
seq_no: 10	Configure the sequence no. as 10
operation: match	onfigures the operation type under route-map as match
protocol: ip	Configures the matching protocol as ip
match: address	Configures the match-type as addressunder route-map LO_RED_TO_0
prefix_list: LO_RED_TO_0	Configure the matching prefix list name

Prefix List Configuration

Template File for Prefix List

ocnos_prefix_list.j2

{%if prefix_list is defined %}

{% for prefixlist in prefix_list.params -%}

{% if prefixlist.eq is defined %}

ip prefix-list {{ prefixlist.name }}

{{prefixlist.prefix}} eq {{ prefixlist.eq }}

{% else %}

ip prefix-list {{ prefixlist.name }}

{% endif %}

{% endfor %} end

{%endif%}

Sample Parameter File for Prefix List

sw2.yml

prefix_list:	prefix-list configurations
params:	prefix-list parameters configuration
- name: only_lo	Configures the name of the prefix-list
seq_no: seq 5	Configures the sequence no. to give the priority to the matched
prefixes
permission: permit	Configure the permission type as permit for prefix-list
prefix: 36.0.0.1/24	Configure the prefix to matched
eq: 32	If defined it wiill confgigure the Exact prefix length to be matched as 32

ACL Configuration

Template File for ACL

ocnos_acl.j2

{%if ACL is defined%}

{% for acl in ACL.params -%}

ip access-list {{ acl.name }}

{% endfor %}

end

{%endif%}

Sample Parameter File for ACL

sw2.yml

ACL:	ACL configurations
params:	ACL parameters configuration
- name: only_lo	Configures the name of the ACL
seq_no: 10	Configures the sequence no. to give the priority to the matched prefixes
permission: permit	Configure the permission type as permit for acl
protocol: any	Configure any command to match any type of protocol packet to match
prefix: 36.0.0.0/24	Configure the prefix to matched
dst: any	Configure the destination address as any
- name: only_lo	Configures the name of the ACL
seq_no: 11	Configures the sequence no. to give the priority to the matched prefixes
permission: deny	Configure the permission type as deny for acl

SNMP Configuration

Template File for SNMP

ocnos_snmp.j2

snmp-server enable snmp vrf {{ snmp.vrf }}

snmp-server view {{ snmp.viewname }} {{ snmp.oid }} included vrf management

snmp-server community {{ snmp.communame }} group network-admin vrf management

{% if snmp.community is defined %}

snmp-server community {{ snmp.community }} group network-operator vrf management

{% endif %}

{% if snmp.hosttest is defined %}

snmp-server host {{ snmp.hosttest }} traps version 2c test udp-port 161 vrf management

{% endif %}

snmp-server host {{ snmp.hostpub }} traps version 2c public udp-port 162 vrf management

{% for traps in snmp.traps -%}

snmp-server enable traps {{ traps.daemon }}

{% endfor -%}

Parameter File for SNMP

sw2.yml

Snmp	Set SNMP service
Traps	globally enable snmp traps
- daemon: bgp	Enable bgp notification trap in global configuration mode
- daemon: isis	Enable isis notification trap in global configuration mode
- daemon: pwdelete	Enable pwdelete notification trap in global configuration mode
- daemon: pw	Enable pw notification trap in global configuration mode
- daemon: mpls	Enable mpls notification trap in global configuration mode
- daemon: ospf	Enable ospf notification trap in global configuration mode
- daemon: rsvp	Enable rsvp notification trap in global configuration mode
vrf: management	Configure vrf name as < snmp-server enable snmp vrf management> to enable snmp
viewname: all	Globally Configure viewname as < snmp-server view all.1 included vrf management>
oid: .1	Specify the OID-Tree in global configs
community: test	Configure community name as test
communame: public	Configure community name as public
hosttest: 10.12.6.247	Configure snmp-server host 10.12.6.247 traps version 2c public udp-port 161 vrf management command globlly
hostpub: 10.12.47.72	Configure snmp-server host 10.12.47.72 traps version 2c public udp-port 162 vrf management command globlly

ISIS Configuration

Template File for ISIS

ocnos_isisagg.j2

key chain {{ key.chain }}

key {{ key.keyid }}

key-string encrypted {{ key.passwd }}

exit

{% for isis in isis.proc1 -%}

router isis {{ isis.processid }}

{% if isis.istype is defined %}

is-type {{ isis.istype }}

{%endif%}

{% if isis.mode is defined %}

authentication mode {{ isis.mode }} {{ isis.level }}

authentication key-chain isis {{ isis.level }}

{%endif%}

{% if isis.level is defined %}

spf-interval-exp {{ isis.spfvalue }} {{isis.spfinmili }}

{%endif%}

{% if isis.level1 is defined %}

spf-interval-exp {{ isis.level1 }} {{ isis.spfvalue }} {{isis.spfinmili }}

{%endif%}

{% if isis.trafficeng is defined %}

metric-style wide {{ isis.trafficeng }}

mpls traffic-eng {{ isis.trafficeng }}

{%endif%}

{% if routerid.address is defined %}

mpls traffic-eng router-id {{ routerid.address }}

{% endif%}

{% if isis.capability is defined %}

capability {{ isis.capability }}

{% endif%}

{% if isis.dynamic is defined %}

dynamic-hostname

{% endif%}

bfd {{ isis.bfd }}

net {{ isis.net }}

{% if isis.metric is defined %}

redistribute isis 1 metric {{ isis.metric }} {{ isis.level }} route-map {{ isis.word }}

{%endif%}

{% if isis.passive is defined %}

passive-interface {{ isis.passive }}

{%endif%}

exit

{% for interface in isis.interfaces -%}

interface {{ interface.name }}

ip router isis {{ interface.isis }}

{% if interface.isisnw is defined %}

isis network {{ interface.isisnw }}

{%endif%}

exit

{% endfor -%}

Parameter File for ISIS

sw2.yml

Key	authentication key management configuratioin
chain: isis	Configure key chain isis command globally
keyid: 1	Configure key identifier number under authentication key management
passwd: 0x46ff28ed3cbff32e	Configure key-string encrypted 0x46ff28ed3cbff32e command under key id
Isis:	Router isis configs
proc1:	ISIS router configuration details
processid: 1	Configure router isis process id 1
istype: level-1	Configure IS Level 1 for this isis routing process
level: level-1	Configure authentication mode md5 level as 1 under router isis 1
spfvalue: 0	Configure spf-interval-exp 0 0 command under router isis 1
spfinmili: 0	Configure SPF calculation in milliseconds in spf-interval-exp 0 0 command under router isis 1
dynamic: dynamic-hostname	Configure dynamic hostname
net: 49.3600.3600.9608.00	Configure net: 49.0002.0000.0000.0099.00 under router isis 0
bfd: all-interfaces	Enable BFD on all interfaces
interfaces:	Interfaces details
- name: xe4	Configure interface xe4 command
isis: 1	Configure ip router isis 1 command under interface xe4
network: point-to-point	Configure isis network point-to-point command
- name: xe2	Configure interface xe2 command
isis: 1	Configure ip router isis 1 command under interface xe2
network: point-to-point	Configure interfacevlan1.1001 command
- name: lo	Configure interface lo command
isis: 1	Configure ip router isis 1 command under interface loopback

Interface Configuration

Template File for Interface Configuration

ocnos_interface.j2

{% for interface in interfaces.ifnames -%}

interface {{ interface.ifname }}

{%if interface.loadinterval is defined %}

load-interval {{ interface.loadinterval }}

{%endif%}

{% if "lo" in interface.ifname %}

ipv6 address {{ interface.address1 }}

bfd session {{ interface.bfdsession }} multihop

{%else%}

{%endif%}

{%if interface.switch is defined %}

{%endif%}

{%if interface.speed is defined %}

speed {{ interface.speed }}

{%endif%}

{% if interface.bridge is defined %}

bridge-group {{ interface.bridge }}

{%endif%}

{% if interface.mode is defined %}

switchport mode {{ interface.mode }}

{%endif%}

{% if interface.vlan is defined %}

switchport trunk allowed vlan {{ interface.vlan }}

{%endif%}

{% if interface.address is defined %}

ip address {{ interface.address }}

{%endif%}

{% if interface.mtu is defined %}

mtu {{ interface.mtu }}

{%endif%}

{% if interface.groupid is defined %}

channel-group {{ interface.groupid }} mode {{ interface.state }}

exit

{% endif %}

{% endfor %}

Parameter File for Interface configuration

sw2.yml

interfaces:	Interface configuration
ifnames:	Interface configuration details
- ifname: xe4	Configure interface xe4
address:10.110.140.20/31	Configure ip address 10.110.140.20/31 command under xe4
mtu: 9216	Configure mtu 9216 under xe4
- ifname: xe2	Configure interface xe2
loadinterval: 30	Configure load interval 30 under interface xe4
address: 10.110.140.61/31	Configure ip address 10.110.140.61/31 command under xe2
mtu: 9216	Configure mtu 9216 under xe2
- ifname: vlan1.1001	Configure interface vlan1.1001 command
address: 192.168.21.212/24	Configure ip address 192.168.21.212/24 command under interface vlan1.1001
- ifname: vlan1.101	Configure interface vlan1.101 command
address: 101.101.101.5/30	Configure ip address 101.101.101.5/30 command under interface vlan1.101
- ifname: lo	Configure interface loopback
address: 36.0.0.8/32	Configure ip address 36.0.0.8/32 command under lopback interfaces
address1: ::1/128	Configure ipv6 address ::1/128 command under loopback interface
bfdsession: 36.0.0.8 36.0.0.1	Configure bfdsession: 36.0.0.8 36.0.0.1 command under loopback interface
- ifname: xe0	Configure interface xe0
switch: switchport	Configure switchport under xe0 interface
bridge: 1	Configure bridge-group 1 under xe0 interface
mode: trunk	Configure switch mode as trunk under xe0 interfaces
vlan: all	Configure switchport trunk allowed vlan all command under int xe0
loadinterval: 30	Configure load-interval 30 under xe0 interfaces
- ifname: xe22	Configure interface xe22 command
switch: switchport	Configure switchport command under xe22 command
bridge: 1	Configure bridge-group 1 under xe22 interface
mode: trunk	Configure switch mode as trunk under xe22 interfaces
vlan: add 101,1001	Configure switchport trunk allowed vlan add 101,1001 command under int xe22
loadinterval: 30	Configure load-interval 30 under xe22 interfaces
mtu: 9216	Configute mtu 9216 under xe22 interface
- ifname: xe6	Configure interface xe6 command
switch: switchport	Configure switchport command under xe6 command
bridge: 1	Configure bridge-group 1 under xe6 interface
mode: access	Configure switch mode as access under xe6 interfaces
- ifname: xe10	Configure interface xe10 command
speed: 1g	Configure speed 1g under interface xe10
- ifname: xe11	Configure interface xe11 command
speed: 1g	Configure speed 1g under interface xe11
- ifname: ce0	Configure interface ce0 command
speed: 40g	Configure speed 40g under interface ce0

BFD Configuration

Template File for BFD

ocnos_bfd.j2

bfd interval {{ bfd.interval }} minrx {{ bfd.minrx }} multiplier {{ bfd.multiplier }}

{% for bfd in bfd.multihoppeer -%}

{% if bfd.address is defined %}

bfd multihop-peer {{ bfd.address }} interval {{ bfd.interval }} minrx {{ bfd.minrx }} multiplier {{ bfd.multiplier }}

{% endif %}

{% endfor -%}

Parameter File for BFD

sw2.yml

bfd	Bfd configuration
interval: 3	Configure globally BFD transmit Interval BFD configuration as 3
minrx: 3	Configure bfd interval 3 minrx 3 multiplier 3 command globally
multiplier: 3	Configure bfd interval 3 minrx 3 multiplier 3 command globally
multihoppeer:	Configure multihoppeer configuration
- address: 36.0.0.1	Configure bfd multihop-peer 36.0.0.1 interval 300 minrx 300 multiplier 5 command globally
interval: 300	Configure bfd multihop-peer 36.0.0.1 interval 300 minrx 300 multiplier 5 command globally
minrx: 300	Configure bfd multihop-peer 36.0.0.1 interval 300 minrx 300 multiplier 5 command globally
multiplier: 5	Configure bfd multihop-peer 36.0.0.1 interval 300 minrx 300 multiplier 5 command globally

Hardware Profile Configuration

Template File for Hardware Profile

Ocnos_hardwareprofile.j2

hardware-profile filter {{ hardware.filter }} enable

{% for statistics in hardware.statistics -%}

hardware-profile statistics {{ statistics.value }} enable

{% endfor -%}

Parameter File for Hardware Profile

sw2.ym

hardware	Hardware configuration
filter: qos-ext	Configure hardware-profile filter qos-txt command under config mode
statistics:	Hardware statistics configuration
- value: ingress-acl	Configure hardware-profile statistics ingress ACL command under config mode
- value: mpls-pwe	Configure hardware-profile statistics mpls-pwe command under config mode

NTP Configuration

Template File for NTP

Ocnos_ntp.j2

feature ntp vrf management

{% for ntp in ntp.states -%}

ntp {{ ntp.state }} vrf management

{% endfor -%}

{% for server in ntp.server -%}

ntp server {{ server.address }} vrf management

{% endfor -%}

logging server {{ ntp.logserver }} 5 vrf management

router-id {{ ntp.routerid }}

service unsupported-transceiver

Parameter File for NTP

sw2.yml

Ntp	NTP configuration
states:	Configure ntp states details
-state: enable	Enable ntp
- state: logging	Configure ntp logging vrf management command
server:	Configure ntp server address
- address: 216.239.35.4	Configure ntp server 216.239.35.4 vrf management command under config mode
logserver: 10.12.47.72	Configure logging server 10.12.47.72 5 vrf management
routerid: 36.0.0.8	Configure router-id 36.0.0.8 command globally

VLAN Configuration

Template File for VLAN

Ocnos_vlan.j2

{% if vlan.protocol is defined %}

bridge 1 protocol {{ vlan.protocol }} vlan-bridge

{%endif %}

vlan {{ vlan.level }}

{% for range in vlan.range -%}

vlan {{ range.value }} bridge {{ vlan.bridge }} state {{ vlan.state }}

{% endfor -%}

Parameter File for VLAN

Sw2.yml

Vlan	Vlan configuration
level: database	Configure VLAN database
range:	Vlan range configuration
- value: 101	Configure vlan 101 bridge 1 state enable command under vlan database
- value: 1001	Configure vlan 1001 bridge 1 state enable command under vlan database
bridge: 1	Configure bridge 1 under vlan database
state: enable	Configure vlan bridge 1 state as enable under vlan database
protocol: rstp	Configure bridge 1 protocol rstp vlan-bridge command globally

LLDP Configuration

Template File for LLDP

Ocnos_lldp.j2

lldp run

{% for lldp in lldp.lldp1 -%}

interface {{ lldp.name }}

set lldp {{ lldp.state }} {{ lldp.mode }}

lldp tlv {{ lldp.MED }} {{ lldp.powerviamdi }} select

set lldp {{ lldp.port }} {{ lldp.ifname}}

set lldp management-address-tlv ip-address

{% for tlvselect in lldp.tlvselect -%}

lldp tlv basic-mgmt {{ tlvselect.mgmt }} select

{% endfor -%}

exit

{% endfor -%}

Parameter File for LLDP

sw2.yml

Lldp	lldp configuration
lldp1:	lldp configuration details
- name: xe2	Configure interface xe2 command
lagent: lldp-agent	Enable lldp agent under xe2 interface
state: enable	Configure set lldp enable txrx command under interface xe2
mode: txrx	Configure lldp mode as txrx under interface xe2
MED: med	Configure lldp tlv-select med media-capabilities command under lldp-agent
powerviamdi: media-capabilities	Configure extended-power-via-mdi media-capailities in lldp tlv-select med media-capabilities command under lldp-agent
port: port-id-tlv	Configure port-id-tlv in set lldp port-id-tlv if-name command under interface xe2
ifname: if-name	Configure if-name as port-id-TLV in set lldp port-id-tlv if-name command under interface xe2
tlvselect :	tlv select configuration
- mgmt: port-description	Configure lldp tlv-select basic-mgmt port-description command under interface xe2
- mgmt: system-name	Configure lldp tlv-select basic-mgmt system-name command under interface xe2
- mgmt: system-capabilities	Configure lldp tlv-select basic-mgmt system-capabilities under interface xe2
- mgmt: system-description	Configure lldp tlv-select basic-mgmt system-description under interface xe2
- mgmt: management-address	Configure lldp tlv-select basic-mgmt management-address under interface xe2
- name: xe10	Configure interface xe10 command
lagent: lldp-agent	Enable lldp agent under xe10 interface
state: enable	Configure set lldp enable txrx command under interface xe10
mode: txrx	Configure lldp mode as txrx under interface xe10
MED: med	Configure lldp tlv-select med media-capabilities command under lldp-agent
powerviamdi: media-capabilities	Configure extended-power-via-mdi media-capailities in lldp tlv-select med media-capabilities command under lldp-agent
port: port-id-tlv	Configure port-id-tlv in set lldp port-id-tlv if-name command under interface xe10
ifname: if-name	Configure if-name as port-id-TLV in set lldp port-id-tlv if-name command under interface xe10
tlvselect :	tlv select configuration
- mgmt: port-description	Configure lldp tlv-select basic-mgmt port-description command under interface xe10
- mgmt: system-name	Configure lldp tlv-select basic-mgmt system-name command under interface xe10
- mgmt: system-capabilities	Configure lldp tlv-select basic-mgmt system-capabilities under interface xe10
- mgmt: system-description	Configure lldp tlv-select basic-mgmt system-description under interface xe10
- mgmt: management-address	Configure lldp tlv-select basic-mgmt management-address under interface xe10
- name: xe11	Configure interface xe11 command
lagent: lldp-agent	Enable lldp agent under xe11 interface
state: enable	Configure set lldp enable txrx command under interface xe11
mode: txrx	Configure lldp mode as txrx under interface xe11
MED: med	Configure lldp tlv-select med media-capabilities command under lldp-agent
powerviamdi: media-capabilities	Configure extended-power-via-mdi media-capailities in lldp tlv-select med media-capabilities command under lldp-agent
port: port-id-tlv	Configure port-id-tlv in set lldp port-id-tlv if-name command under interface xe11
ifname: if-name	Configure if-name as port-id-TLV in set lldp port-id-tlv if-name command under interface xe11
tlvselect :	tlv select configuration
- mgmt: port-description	Configure lldp tlv-select basic-mgmt port-description command under interface xe11
- mgmt: system-name	Configure lldp tlv-select basic-mgmt system-name command under interface xe11
- mgmt: system-capabilities	Configure lldp tlv-select basic-mgmt system-capabilities under interface xe11
- mgmt: system-description	Configure lldp tlv-select basic-mgmt system-description under interface xe11
- mgmt: management-address	Configure lldp tlv-select basic-mgmt management-address under interface xe11
- name: xe4	Configure interface xe4 command
state: enable	Enable lldp agent under xe4 interface
lagent: lldp-agent	Configure set lldp enable txrx command under interface xe4
mode: txrx	Configure lldp mode as txrx under interface xe4
MED: med	Configure lldp tlv-select med media-capabilities command under lldp-agent
powerviamdi: media-capabilities	Configure extended-power-via-mdi media-capailities in lldp tlv-select med media-capabilities command under lldp-agent
port: port-id-tlv	Configure port-id-tlv in set lldp port-id-tlv if-name command under interface xe4
ifname: if-name	Configure if-name as port-id-TLV in set lldp port-id-tlv if-name command under interface xe4
tlvselect :	tlv select configuration
- mgmt: port-description	Configure lldp tlv-select basic-mgmt port-description command under interface xe4
- mgmt: system-name	Configure lldp tlv-select basic-mgmt system-name command under interface xe4
- mgmt: system-capabilities	Configure lldp tlv-select basic-mgmt system-capabilities under interface xe4
- mgmt: system-description	Configure lldp tlv-select basic-mgmt system-description under interface xe4
- mgmt: management-address	Configure lldp tlv-select basic-mgmt management-address under interface xe4

Limitations

The following are the current limitations while configuring OcNOS through Ansible.

1. The following commands in OcNOS require the device to be rebooted to be effective.

• hardware-profile

• forwarding profile

• maximum-paths

• copy empty-config startup-config

Ansible returns success while configuring these commands. However, the device needs to be rebooted to make these effective.

2. By default, ANSIBLE_PERSISTENT_COMMAND_TIMEOUT is set to 30 (seconds). While pushing large configs through Ansible which might be taking more time than this default timeout, it is suggested that to increase the ansible_command_timeout to appropriate value. In group_vars/ocnos.yml, it is suggested to add the below line with appropriate timeout value:

ansible_command_timeout: 1800

3. While configuring the below commands, there are certain warning messages shown to the customer. Currently Ansible treats them as failure and returns failure even though it is successful. It is suggested that the user takes appropriate action while configuring these commands.

• no ip vrf <vrf-id>

• While re-configuring shaping as part of QoS:

policy-map type queuing shaper

class type queuing defaultq

shape 10 gbps

exit