OcNOS DC : OpenConfig Command Reference
OpenConfig Command Reference
 
Introduction
Overview
Prerequisites
Troubleshooting
Limitations
OpenConfig Configurations
Network-instance Object Values for “type” Attribute
Enable OpenConfig Translation
OpenConfig Optical-Channel and Terminal Device
Overview
Enable OpenConfig Translation
Enable Coherent modules
Host Interface, Network Interface, and Logical Channels
Loopback-type on Host Interface
Loopback-type on Network Interface
Disable Coherent-Modules
Operational-Mode
Soft-tx-disable
tx-laser-freq
tx-output-power
ISIS OpenConfig Translation
General Restrictions
Create IS-IS instance
Configure global parameters
Configure level traffic-engineering
Configure AF IPv6 support
Configure metric parameter on AF IPv6
Configure Global Timers parameters
Configure Global Transport parameter
Configure LSP-BIT parameter
Configure Inter-level Propagation Policies parameter
Configure Graceful Restart parameter
Configure Metric Style parameter
Configure Authentication parameter
Configure Interface IS-IS Parameter
Configure Interface Authentication Parameter
Configure Interface IGP-LDP-SYNC Parameter
Configure Interface Circuit-type Parameter
Configure Primary IP Address
Configure Interface Passive Parameter
Configure Interface IPv6 AF Parameter
Configure Interface BFD Parameter
Configure Interface Priority Parameter
Configure Interface Timers Parameter
BGP OpenConfig Translation
Create BGP Instance
Create BGP Global with default VRF
Create BGP Global with User-defined VRFs
Create BGP Neighbors
Configure eBGP Neighbor with TTL
Create BGP Peer-groups with Default VRF
Create BGP Peer-groups with User-defined VRFs
Configure Update-source on Neighbor
Double Link in Load Balance
Delete BGP Instance
BGP RIB Counters IPv4
BGP RIB Counters IPv6
OSPFv2 Openconfig Translation
Create OSPF Process
Create OSPF Process
Interface Configuration OpenConfig Translation
Configure Interfaces
Configure Description
Configure MTU
Configure Primary IP Address
Configure Secondary IP Address
Configure IPv6 Addresses
Configure Duplex-mode
Configure Port-Speed
Configure Ethernet Type
Configure Sub-interface with Primary and Secondary Addresses
LACP OpenConfig Translation
Create Static LAG Interface
Create Dynamic LAG Interface
Tunnel Interfaces OpenConfig Translation
Create Tunnel Interface
Static Route OpenConfig Translation
Create a static route
Create a Static Route with Load Balancing
Create a Static Route with Active/Standby
Platform OpenConfig Translation
Description
RAM
Hard-disk
PSU
Temperature
Transceiver
EEPROM
CPU
System OpenConfig Translation
Host
TimeZone Clock
Rsyslog
Logging Remote Server
Release
Logging Remote Facility
Alarms
VLAN OpenConfig Translation
Match Single Tagged VLAN
Match single tagged VLAN range
Match double tagged VLAN
Match double tagged with outer and inner VLAN
Ingress-mapping actions
Trunk VLANs in interface
Trunk interface with native VLAN
Access VLAN in interface
Trunk VLANs in link aggregation interface
Trunk LAG with native VLAN
Creation of a cross connect
Deletion of a cross connect
Configure Bridge Domain and associate L2 Subinterfaces
Deletion of a Bridge Domain instance
Creation of a VLAN bridge
LLDP OpenConfig Translation
Enable Management Attributes
Configure chassis-id
Configure suppress advertisement
Configure system name
Enable LLDP on an interface
LLDP get Attributes
Interface counters
Neighbors
Neighbors name and description
Neighbors chassis-id, type and ttl
Neighbors port-id, type and description
Neighbors custom TLVs type/subtype
Neighbors custom TLVs
Neighbors capabilities
ACL OpenConfig Translation
Enable Management Attributes
Create IPv4 Entries
Create IPv6 Entries
Create Interfaces Egress for IPv4/IPv6
Create Interfaces Ingress for IPv4/IPv6
Create Interfaces Egress for L2
Create Interfaces Ingress for L2
QoS OpenConfig Translation
Enable QoS on OcNOS
Enable QoS Profile on OcNOS
Create Classifiers Profiles
Create Forwarding-groups Profiles
Create Queues and Queue-Management-profiles Entries
Create Scheduler-policies Entries
Create Scheduler-policies entries without leaf max-queue-depth-bytes
Create Scheduler-policies Entries with leaf max-queue-depth-bytes
Create Interfaces Classifier Association
Create Interfaces Scheduler-policies Association
OpenZR+ OpenConfig Translation
General Restrictions
Disable/enable OpenZR+ transceiver
Configure OpenZR+ optical channel operational mode
Configure OpenZR+ optical channel target output power
Configure OpenZR+ optical channel frequency
Configure OpenZR+ loopback mode
Validate OpenZR+ module state
Validate OpenZR+ transceiver state
Validate OpenZR+ transceiver thresholds
Validate OpenZR+ transceiver physical channels
Validate OpenZR+ transceiver optical channel state
Validate OpenZR+ logical channels
Configure OpenZR+ port-breakout
Validate OpenZR+ port-breakout