OcNOS-RON : Virtual Extensible LAN Guide : Virtual eXtensible Local Area Network Configuration Guide : VXLAN Tunnel Over SVI
VXLAN Tunnel Over SVI
This chapter contains the configurations for VXLAN Tunnel Over SVI.
Overview
VxLAN EVPN solution is envisioned to simplify the topology and configurations in Data Centers (DC). In Data Centers, CLOS topology was used, which makes network side pure L3 and uses EBGP as IGP.
VxLAN solution is required for Service Providers (SP) as well to run few of the services or all services in their network over VxLAN. When they choose to run few services over VxLAN, then on the network side there will be a need to run VxLAN over SVI.
Topology
The Topology shown below contains the 3 VTEPS i.e VTEP1 ,VTEP2 and VTEP3 and 3 core nodes P1 ,P2 and P3. Vxlan tunnel will be established between VTEPS over SVI interfaces. OSPF as IGP will be running between VTEPS and the core node to provide the end to end connectivity. Switch is connected between host and VTEP-1, VTEP-2 via dynamic LAG.
VXLAN over SVI
RTR1/VTEP1
 
VTEP1#configure terminal
Enter configuration terminal
VTEP1(config)#hostname VTEP1
Configure hostname
VTEP1(config)#mac vrf vrf1
Configure MAC vrf vrf1
VTEP1(config-vrf)#rd 1.1.1.1:11
Configure RD for vrf1
VTEP1(config-vrf)#route-target both 10.10.10.10:100
Configure RT for vrf1
VTEP1(config-vrf)#mac vrf vrf2
Configure MAC vrf vrf2
VTEP1(config-vrf)#rd 1.1.1.1:12
Configure RD for vrf2
VTEP1(config-vrf)#route-target both 10.10.10.10:102
Configure RT for vrf2
VTEP1(config-vrf)#bfd interval 3 minrx 3 multiplier 3
Configure BFD interval globally
VTEP1(config)#evpn vxlan multihoming enable
Enable EVPN VXLAN multihoming
VTEP1(config)#nvo vxlan enable
Enable VXLAN
VTEP1(config)#qos enable
Enable qos
VTEP1(config)#qos statistics
Enable qos statistics
VTEP1(config)#bridge 1 protocol ieee vlan-bridge
Configure IEEE VLAN bridge
VTEP1(config)#no bridge 1 spanning-tree enable
Disable spanning tree in bridge 1 globally
VTEP1(config)#no igmp snooping
Disable igmp snooping messages globally
VTEP1(config)#vlan database
Enter into the VLAN database
VTEP1(config-vlan)#vlan 10-200 bridge 1 state enable
Configure VLAN 10-200 and associate with bridge 1
VTEP1(config-vlan)#vlan 4000 bridge 1 state enable
Configure VLAN 4000 and associate with bridge 1
VTEP1(config-vlan)#interface po1
Enter interface mode
VTEP1(config-if)#switchport
Set the interface as Layer2 port
VTEP1(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP1(config-if)#evpn multi-homed system-mac aa22.3344.5566
Configure EVPN system-MAC
VTEP1(config-if)#interface lo
Enter lo interface mode
VTEP1(config-if)#ip address 1.1.1.1/32 secondary
Assign loopback IP
VTEP1(config-if)#interface vlan1.10
Specify interface VLAN1.10 to be configured.
VTEP1(config-if)#ip address 12.1.1.1/24
Assign IP address
VTEP1(config-if)#ip ospf cost 1
Change OSPF cost of the link
VTEP1(config-if)#interface vlan1.20
Specify interface VLAN1.20 to be configured.
VTEP1(config-if)#ip address 13.1.1.1/24
Assign IP address
VTEP1(config-if)#ip ospf cost 1
Change OSPF cost of the link
VTEP1(config-if)#interface vlan1.30
Specify interface VLAN1.30 to be configured.
VTEP1(config-if)#ip address 14.1.1.1/24
Assign IP address
VTEP1(config-if)#ip ospf cost 1
Change OSPF cost of the link
VTEP1(config-if)#interface xe1
Enter interface mode
VTEP1(config-if)#switchport
Set the interface as Layer2 port
VTEP1(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
VTEP1(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
VTEP1(config-if)#switchport trunk allowed vlan add 20,29
Enable VLAN's allowed on this interface.
VTEP1(config-if)#switchport trunk native vlan 29
Configure native VLAN
VTEP1(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP1(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
VTEP1(config-if)#interface xe5
Enter interface mode
VTEP1(config-if)#switchport
Set the interface as Layer2 port
VTEP1(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
VTEP1(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
VTEP1(config-if)#switchport trunk allowed vlan add 10,19
Enable VLAN's allowed on this interface.
VTEP1(config-if)#switchport trunk native vlan 19
Configure native VLAN
VTEP1(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP1(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
VTEP1(config-if)#interface xe7
Enter interface mode
VTEP1(config-if)#switchport
Set the interface as Layer2 port
VTEP1(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
VTEP1(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
VTEP1(config-if)#switchport trunk allowed vlan add 30,39
Enable VLAN's allowed on this interface.
VTEP1(config-if)#switchport trunk native vlan 39
Configure native VLAN
VTEP1(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP1(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
VTEP1(config-if)#interface xe41
Enter interface mode
VTEP1(config-if)#channel-group 1 mode active
Map this interface to po1
VTEP1(config-if)#interface xe42
Enter interface mode
VTEP1(config-if)#channel-group 1 mode active
Map this interface to po1
VTEP1(config-if)#interface xe46
Enter interface mode
VTEP1(config-if)#switchport
Map this interface to po1
VTEP1(config-if)#router ospf 1
Enter OSPF configuration mode
VTEP1(config-router)#ospf router-id 1.1.1.1
Configure OSPF router id
VTEP1(config-router)#bfd all-interfaces
Enable BFD in all OSPF interfaces
VTEP1(config-router)#network 1.1.1.1/32 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP1(config-router)#network 12.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP1(config-router)#network 13.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP1(config-router)#network 14.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP1(config-router)#router bgp 100
Enter Router BGP mode and define the AS number 100.
VTEP1(config-router)#address-family ipv4 unicast
Enter address-family IPv4 unicast mode
VTEP1(config-router)#network 1.1.1.1/32
Add the lo network to BGP route
VTEP1(config-router-af)#neighbor 2.2.2.2 activate
Activate neigbors
VTEP1(config-router-af)#neighbor 6.6.6.6 activate
Activate neigbors
VTEP1(config-router-af)#exit-address-family
Exit address-family mode.
VTEP1(config-router)#neighbor 2.2.2.2 remote-as 100
Configure BGP remote-as 100 with neighbor IP
VTEP1(config-router)#neighbor 2.2.2.2 update-source lo
Define BGP neighbors, to update the source routes with lo
VTEP1(config-router)#neighbor 2.2.2.2 advertisement-interval 0
Configure advertisement-interval as 0 for fast convergence for VTEP2
VTEP1(config-router)#neighbor 6.6.6.6 remote-as 100
Configure BGP remote-as 100 with neighbor IP
VTEP1(config-router)#neighbor 6.6.6.6 update-source lo
Define BGP neighbors, to update the source routes with lo
VTEP1(config-router)#neighbor 6.6.6.6 advertisement-interval 0
Configure advertisement-interval as 0 for fast convergence for VTEP3
VTEP1(config-router)#address-family l2vpn evpn
Enter in to BGP L2VPN EVPN address-family
VTEP1(config-router-af)#neighbor 2.2.2.2 activate
Activate neigbors
VTEP1(config-router-af)#neighbor 6.6.6.6 activate
Activate neigbors
VTEP1(config-router-af)#exit-address-family
Exit from BGP L2VPN EVPN address-family
VTEP1(config-router)#nvo vxlan vtep-ip-global 1.1.1.1
Configure VXLAN global IP
VTEP1(config)#nvo vxlan id 1 ingress-replication inner-vid-disabled
Create VNID 1
VTEP1(config-nvo)#vxlan host-reachability-protocol evpn-bgp vrf1
Associate VNID with EVPN and vrf1
VTEP1(config-nvo)#nvo vxlan id 1000 ingress-replication inner-vid-disabled
Create VNID 1000
VTEP1(config-nvo)#vxlan host-reachability-protocol evpn-bgp vrf2
Associate VNID with EVPN and vrf2
VTEP1(config-nvo-acc-if)#nvo vxlan access-if port-vlan po1 2000
Create VXLAN access port port-vlan
VTEP1(config-nvo-acc-if)#no shutdown
Unshut the access interface
VTEP1(config-nvo-acc-if)#map vnid 1000
Map the VNID to access-if
VTEP1(config-nvo)#nvo vxlan access-if port xe46
Create VXLAN access port
VTEP1(config-nvo-acc-if)#no shutdown
Unshut the access interface
VTEP1(config-nvo-acc-if)#map vnid 1
Map the VNID to access-if
VTEP1(config-nvo-acc-if)#nvo vxlan access-if port-vlan po1 1000
Create VXLAN access port port-vlan
VTEP1(config-nvo-acc-if)#no shutdown
Unshut the access interface
VTEP1(config-nvo-acc-if)#map vnid 1
Map the VNID to access-if
VTEP1(config-nvo-acc-if)#mac 0000.1111.1111 ip 100.1.1.100
Configure static MAC IP
VTEP1(config-nvo-acc-if)#mac 0000.1111.1112
Configure static MAC
VTEP1(config-nvo-acc-if)#mac 0000.1111.1113
Configure static MAC
VTEP1(config-nvo-acc-if)#mac 0000.1111.1114
Configure static MAC
VTEP1(config-nvo-acc-if)#mac 0000.1111.1115
Configure static MAC
VTEP1(config-nvo-acc-if)#commit
Commit the candidate configuration to the running configuration
VTEP2
 
VTEP2#configure terminal
Enter configuration terminal
VTEP2(config)#hostname VTEP2
Configure hostname
VTEP2(config)#mac vrf vrf1
Configure MAC VRF vrf1
VTEP2(config-vrf)#rd 2.2.2.2:11
Configure RD for vrf1
VTEP2(config-vrf)#route-target both 10.10.10.10:100
Configure RT for vrf1
VTEP2(config-vrf)#mac vrf vrf2
Configure MAC VRF vrf2
VTEP2(config-vrf)#rd 2.2.2.2:12
Configure RD for vrf2
VTEP2(config-vrf)#route-target both 10.10.10.10:102
Configure RT for vrf2
VTEP2(config)#nvo vxlan enable
Enable VXLAN
VTEP2(config)#evpn vxlan multihoming enable
Enable EVPN VXLAN multihoming
VTEP2(config)#qos enable
Enable QOS
VTEP2(config)#qos statistics
Enable QOS statistics
VTEP2(config)#bridge 1 protocol ieee vlan-bridge
Configure IEEE VLAN bridge
VTEP2(config)#no bridge 1 spanning-tree enable
Disable spanning tree in bridge 1 globally
VTEP2(config)#vlan database
Enter into the VLAN database
VTEP2(config-vlan)#vlan 10-200 bridge 1 state enable
Configure VLAN 10-200 and associate with bridge 1
VTEP2(config-vlan)#interface po1
Enter interface mode
VTEP2(config-if)#switchport
Set the interface as Layer2 port
VTEP2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP2(config-if)#evpn multi-homed system-mac aa22.3344.5566
Configure EVPN system-MAC
VTEP2(config-if)#interface lo
Enter interface mode
VTEP2(config-if)#ip address 2.2.2.2/32 secondary
Configure loopback IP
VTEP2(config-if)#interface vlan1.10
Specify interface VLAN1.10 to be configured.
VTEP2(config-if)#ip address 12.1.1.2/24
Assign IP address
VTEP2(config-if)#interface vlan1.40
Specify interface VLAN1.40 to be configured.
VTEP2(config-if)#ip address 23.1.1.1/24
Assign IP address
VTEP2(config-if)#ip ospf cost 1
Change OSPF cost of the link
VTEP2(config-if)#interface vlan1.50
Specify interface VLAN1.50 to be configured.
VTEP2(config-if)#ip address 24.1.1.1/24
Assign IP address
VTEP2(config-if)#interface ce53
Enter interface mode
VTEP2(config-if)#switchport
Set the interface as Layer2 port
VTEP2(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
VTEP2(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
VTEP2(config-if)#switchport trunk allowed vlan add 40,49
Enable VLAN's allowed on this interface.
VTEP2(config-if)#switchport trunk native vlan 49
Configure native VLAN
VTEP2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP2(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
VTEP2(config-if)#interface xe5
Enter interface mode
VTEP2(config-if)#switchport
Set the interface as Layer2 port
VTEP2(config-if)#bridge-group 1 spanningtree disable
Associate the interface with bridge group 1 and disable spanning tree
VTEP2(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode
VTEP2(config-if)#switchport trunk allowed vlan add 10,19
Enable VLAN's allowed on this interface
VTEP2(config-if)#switchport trunk native vlan 19
Configure native VLAN
VTEP2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP2(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
VTEP2(config-if)#interface xe9
Enter interface mode
VTEP2(config-if)#switchport
Set the interface as Layer2 port
VTEP2(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
VTEP2(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
VTEP2(config-if)#switchport trunk allowed vlan add 50,59
Enable VLAN's allowed on this interface.
VTEP2(config-if)#switchport trunk native vlan 59
Configure native VLAN
VTEP2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP2(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
VTEP2(config-if)#interface xe41
Enter interface mode
VTEP2(config-if)#channel-group 1 mode active
Map the interface to po1
VTEP2(config-if)#interface xe42
Enter interface mode
VTEP2(config-if)#channel-group 1 mode active
Map the interface to po1
VTEP2(config-if)#interface xe47
Enter interface mode
VTEP2(config-if)#switchport
Set the interface as Layer2 port
VTEP2(config-if)#router ospf 1
Enter OSPF configuration mode
VTEP2(config-router)#ospf router-id 2.2.2.2
Configure OSPF router id
VTEP2(config-router)#network 2.2.2.2/32 area 0.0.0.0
Enable BFD in all ospf interfaces
VTEP2(config-router)#network 12.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP2(config-router)#network 23.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP2(config-router)#network 24.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP2(config-router)#network 25.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP2(config-router)#router bgp 100
Enter Router BGP mode and define the AS number 100.
VTEP2(config-router)#address-family ipv4 unicast
Enter address-family IPv4 unicast mode
VTEP2(config-router)#network 2.2.2.2/32
Add the lo network to BGP route
VTEP2(config-router-af)#neighbor 1.1.1.1 activate
Activate neigbors
VTEP2(config-router-af)#neighbor 6.6.6.6 activate
Activate neigbors
VTEP2(config-router-af)#exit-address-family
Exit address-family mode.
VTEP2(config-router)#neighbor 1.1.1.1 remote-as 100
Configure BGP remote-as 100 with neighbor IP
(config-router)#neighbor 1.1.1.1 advertisement-interval 0
Configure advertisement-interval as 0 for fast convergence for VTEP1
VTEP2(config-router)#neighbor 1.1.1.1 update-source lo
Define BGP neighbors, to update the source routes with lo
VTEP2(config-router)#neighbor 6.6.6.6 remote-as 100
Configure BGP remote-as 100 with neighbor IP
(config-router)#neighbor 6.6.6.6 advertisement-interval 0
Configure advertisement-interval as 0 for fast convergence for VTEP3
VTEP2(config-router)#neighbor 6.6.6.6 update-source lo
Define BGP neighbors, to update the source routes with lo
VTEP2(config-router)#address-family l2vpn evpn
Enter in to BGP L2VPN EVPN address-family
VTEP2(config-router-af)#neighbor 1.1.1.1 activate
Activate neigbors
VTEP2(config-router-af)#neighbor 6.6.6.6 activate
Activate neigbors
VTEP2(config-router-af)#exit-address-family
Exit from BGP L2VPN EVPN address-family
VTEP2(config-router)#nvo vxlan vtep-ip-global 2.2.2.2
Configure VXLAN global IP
VTEP2(config)#nvo vxlan id 1 ingress-replication inner-vid-disabled
Create VNID 1
VTEP2(config-nvo)#vxlan host-reachability-protocol evpn-bgp vrf1
Associate VNID with EVPN and vrf1
VTEP2(config-nvo)#nvo vxlan id 1000 ingress-replication inner-vid-disabled
Create VNID 1000
VTEP2(config-nvo)#vxlan host-reachability-protocol evpn-bgp vrf2
Associate VNID with EVPN and vrf2
VTEP2(config-nvo)#nvo vxlan access-if port xe47
Create VXLAN access port
VTEP2(config-nvo-acc-if)#map vnid 1
Map the VNID to access-if
VTEP2(config-nvo-acc-if)#nvo vxlan access-if port-vlan po1 2001
Create VXLAN access port
VTEP2(config-nvo-acc-if)#map vnid 1000
Map the VNID to access-if
VTEP2(config-nvo-acc-if)#nvo vxlan access-if port-vlan po1 2000
Create VXLAN access port
VTEP2(config-nvo-acc-if)#map vnid 1000
Map the VNID to access-if
VTEP2(config-nvo-acc-if)#commit
Commit the candidate configuration to the running configuration
P1
 
P1#configure terminal
Enter configuration terminal
P1(config)#hostname P1
Configure hostname
P1(config)#bfd interval 3 minrx 3 multiplier 3
Configure BFD interval globally
P1(config)#qos enable
Enable qos
P1(config)#bridge 1 protocol ieee vlan-bridge
Configure IEEE VLAN bridge
P1(config)#no bridge 1 spanning-tree enable
Disable spanning tree in bridge 1 globally
P1(config)#no igmp snooping
Disable igmp snooping messages globally
P1(config)#vlan database
Enter into the VLAN database
P1(config-vlan)#vlan 10-200 bridge 1 state enable
Configure VLAN 10-200 and associate with bridge 1
P1(config-if)#interface lo
Enter loopback interface mode
P1(config-if)#ip address 3.3.3.3/32 secondary
Assign loopback IP
P1(config-if)#interface vlan1.20
Specify interface VLAN1.20 to be configured.
P1(config-if)#ip address 13.1.1.2/24
Assign IP address
P1(config-if)#ip ospf cost 1
Change OSPF cost of the link
P1(config-if)#interface vlan1.40
Specify interface VLAN1.40 to be configured.
P1(config-if)#ip address 23.1.1.2/24
Assign IP address
P1(config-if)#interface vlan1.60
Specify interface VLAN1.60 to be configured.
P1(config-if)#ip address 35.1.1.1/24
Assign IP address
P1(config-if)#ip ospf cost 1
Change OSPF cost of the link
P1(config-if)#interface vlan1.100
Specify interface VLAN1.100 to be configured.
P1(config-if)#ip address 34.1.1.1/24
Assign IP address
P1(config-if)#ip ospf cost 1
Change OSPF cost of the link
P1(config-vlan)#interface ce49
Enter interface mode
P1(config-if)#switchport
Set the interface as Layer2 port
P1(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P1(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P1(config-if)#switchport trunk allowed vlan add 40,49
Enable VLAN's allowed on this interface.
P1(config-if)#switchport trunk native vlan 49
Configure native VLAN
P1(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P1(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P1(config-if)#interface xe1
Enter interface mode
P1(config-if)#switchport
Set the interface as Layer2 port
P1(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P1(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P1(config-if)#switchport trunk allowed vlan add 20,29
Enable VLAN's allowed on this interface.
P1(config-if)#switchport trunk native vlan 29
Configure native VLAN
P1(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P1(config-if)#mtu 1600
Change the interface mtu value
P1(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P1(config-if)#interface xe10
Enter interface mode
P1(config-if)#switchport
Set the interface as Layer2 port
P1(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P1(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P1(config-if)#switchport trunk allowed vlan add 60,69
Enable VLAN's allowed on this interface.
P1(config-if)#switchport trunk native vlan 69
Configure native VLAN
P1(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P1(config-if)#mtu 1600
Change the interface mtu value
P1(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P1(config-if)#interface xe25
Enter interface mode
P1(config-if)#switchport
Set the interface as Layer2 port
P1(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P1(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P1(config-if)#switchport trunk allowed vlan add 100,109
Enable VLAN's allowed on this interface.
P1(config-if)#switchport trunk native vlan 109
Configure native VLAN
P1(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P1(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P1(config-if)#router ospf 1
Enter OSPF configuration mode
P1(config-router)#ospf router-id 3.3.3.3
Configure OSPF router id
P1(config-router)#bfd all-interfaces
Enable BFD in all OSPF interfaces
P1(config-router)#network 3.3.3.3/32 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P1(config-router)#network 10.10.10.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P1(config-router)#network 13.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P1(config-router)#network 23.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P1(config-router)#network 34.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P1(config-router)#network 35.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P1(config-router)#commit
Commit the candidate configuration to the running configuration
P2
 
P2#configure terminal
Enter configuration terminal
P2(config)#bfd interval 3 minrx 3 multiplier 3
Configure BFD interval globally
P2(config)#qos enable
Enable qos
P2(config)#hostname P2
Configure hostname
P2(config)#bridge 1 protocol ieee vlan-bridge
Configure IEEE VLAN bridge
P2(config)#no bridge 1 spanning-tree enable
Disable spanning tree in bridge 1 globally
P2(config)#no igmp snooping
Disable igmp snooping messages globally
P2(config)#vlan database
Enter into the VLAN database
P2(config-vlan)#vlan 10-200 bridge 1 state enable
Configure VLAN 10-200 and associate with bridge 1
P2(config-vlan)#interface lo
Enter lo interface mode
P2(config-if)#ip address 4.4.4.4/32 secondary
Assign loopback IP
P2(config-if)#interface vlan1.30
Specify interface VLAN1.30 to be configured.
P2(config-if)#ip address 14.1.1.2/24
Assign IP address
P2(config-if)#ip ospf cost 1
Change OSPF cost of the link
P2(config-if)#interface vlan1.50
Specify interface VLAN1.50 to be configured.
P2(config-if)#ip address 24.1.1.2/24
Assign IP address
P2(config-if)#interface vlan1.70
Specify interface VLAN1.70 to be configured.
P2(config-if)#ip address 45.1.1.1/24
Assign IP address
P2(config-if)#ip ospf cost 1
Change OSPF cost of the link
P2(config-if)#interface vlan1.90
Specify interface VLAN1.90 to be configured.
P2(config-if)#ip address 46.1.1.1/24
Assign IP address
P2(config-if)#ip ospf cost 1
Change OSPF cost of the link
P2(config-if)#interface vlan1.100
Specify interface VLAN1.100 to be configured.
P2(config-if)#ip address 34.1.1.2/24
Assign IP address
P2(config-if)#ip ospf cost 1
Change OSPF cost of the link
P2(config-if)#interface xe2
Enter interface mode
P2(config-if)#switchport
Set the interface as Layer2 port
P2(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P2(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P2(config-if)#switchport trunk allowed vlan add 70,79
Enable VLAN's allowed on this interface.
P2(config-if)#switchport trunk native vlan 79
Configure native VLAN
P2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P2(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P2(config-if)#interface xe3
Enter interface mode
P2(config-if)#switchport
Set the interface as Layer2 port
P2(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P2(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P2(config-if)#switchport trunk allowed vlan add 90,99
Enable VLAN's allowed on this interface.
P2(config-if)#switchport trunk native vlan 99
Configure native VLAN
P2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P2(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P2(config-if)#interface xe7
Enter interface mode
P2(config-if)#switchport
Set the interface as Layer2 port
P2(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P2(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P2(config-if)#switchport trunk allowed vlan add 30,39
Enable VLAN's allowed on this interface.
P2(config-if)#switchport trunk native vlan 39
Configure native VLAN
P2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P2(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P2(config-if)#interface xe9
Enter interface mode
P2(config-if)#switchport
Set the interface as Layer2 port
P2(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P2(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P2(config-if)#switchport trunk allowed vlan add 50,59
Enable VLAN's allowed on this interface.
P2(config-if)#switchport trunk native vlan 59
Configure native VLAN
P2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P2(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P2(config-if)#interface xe25
Enter interface mode
P2(config-if)#switchport
Set the interface as Layer2 port
P2(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P2(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P2(config-if)#switchport trunk allowed vlan add 100,109
Enable VLAN's allowed on this interface.
P2(config-if)#switchport trunk native vlan 109
Configure native VLAN
P2(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P2(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P2(config-if)#router ospf 1
Enter OSPF configuration mode
P2(config-router)#ospf router-id 4.4.4.4
Configure OSPF router id
P2(config-router)#bfd all-interfaces
Enable BFD in all OSPF interfaces
P2(config-router)#network 4.4.4.4/32 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P2(config-router)#network 14.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P2(config-router)#network 24.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P2(config-router)#network 34.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P2(config-router)#network 45.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P2(config-router)#network 46.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P2(config-router)#commit
Commit the candidate configuration to the running configuration
P3
 
P3(config)#hostname P3
Configure hostname
P3(config)#bfd interval 3 minrx 3 multiplier 3
Configure BFD interval globally
P3(config)#qos enable
Enable qos
P3(config)#bridge 1 protocol ieee vlan-bridge
Configure IEEE VLAN bridge
P3(config)#no bridge 1 spanning-tree enable
Disable spanning tree in bridge 1 globally
P3(config)#no igmp snooping
Disable igmp snooping messages globally
P3(config)#vlan database
Enter into the VLAN database
P3(config-vlan)#vlan 10-200 bridge 1 state enable
Configure VLAN 10-200 and associate with bridge 1
P3(config-vlan)#interface lo
Enter lo interface mode
P3(config-if)#ip address 5.5.5.5/32 secondary
Assign loopback IP
P3(config-if)#interface vlan1.60
Specify interface VLAN1.60 to be configured.
P3(config-if)#ip address 35.1.1.2/24
Assign IP address
P3(config-if)#ip ospf cost 1
Change OSPF cost of the link
P3(config-if)#interface vlan1.70
Specify interface VLAN1.70 to be configured.
P3(config-if)#ip address 45.1.1.2/24
Assign IP address
P3(config-if)#ip ospf cost 1
Change OSPF cost of the link
P3(config-if)#interface vlan1.80
Specify interface VLAN1.80 to be configured.
P3(config-if)#ip address 56.1.1.1/24
Assign IP address
P3(config-if)#ip ospf cost 1
Change OSPF cost of the link
P3(config-if)#interface vlan1.110
Specify interface VLAN1.1100 to be configured.
P3(config-if)#ip address 15.1.1.2/24
Assign IP address
P3(config-if)#ip ospf cost 1
Change OSPF cost of the link
P3(config-if)#interface vlan1.160
Specify interface VLAN1.160 to be configured.
P3(config-if)#ip address 25.1.1.2/24
Assign IP address
P3(config-if)#ip ospf cost 1
Change OSPF cost of the link
P3(config-if)#interface xe2
Enter interface mode
P3(config-if)#switchport
Set the interface as Layer2 port
P3(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P3(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P3(config-if)#switchport trunk allowed vlan add 70,79
Enable VLAN's allowed on this interface.
P3(config-if)#switchport trunk native vlan 79
Configure native VLAN
P3(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P3(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P3(config-if)#interface xe10
Enter interface mode
P3(config-if)#switchport
Set the interface as Layer2 port
P3(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P3(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P3(config-if)#switchport trunk allowed vlan add 60,69
Enable VLAN's allowed on this interface.
P3(config-if)#switchport trunk native vlan 69
Configure native VLAN
P3(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P3(config-if)#mtu 1600
Change interface mtu value
P3(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P3(config-if)#interface xe15
Enter interface mode
P3(config-if)#switchport
Set the interface as Layer2 port
P3(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
P3(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
P3(config-if)#switchport trunk allowed vlan add 80,89
Enable VLAN's allowed on this interface.
P3(config-if)#switchport trunk native vlan 89
Configure native VLAN
P3(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
P3(config-if)#mtu 1600
Change interface mtu value
P3(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
P3(config-if)#router ospf 1
Enter OSPF configuration mode
P3(config-router)#ospf router-id 5.5.5.5
Configure OSPF router id
P3(config-router)#bfd all-interfaces
Enable BFD in all ospf interfaces
P3(config-router)#network 5.5.5.5/32 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P3(config-router)#network 15.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P3(config-router)#network 25.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P3(config-router)#network 35.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P3(config-router)#network 45.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P3(config-router)#network 56.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
P3(config-router)#commit
Commit the candidate configuration to the running configuration
VTEP3
 
VTEP3#configure terminal
Enter configuration terminal
VTEP3(config)#hostname VTEP3
Configure hostname
VTEP3(config)#mac vrf vrf1
Configure MAC vrf vrf1
VTEP3(config-vrf)#rd 6.6.6.6:11
Configure RD for vrf1
VTEP3(config-vrf)#route-target both 10.10.10.10:100
Configure RT for vrf1
VTEP3(config-vrf)#mac vrf vrf2
Configure MAC vrf vrf2
VTEP3(config-vrf)#rd 6.6.6.6:12
Configure RD for vrf2
VTEP3(config-vrf)#route-target both 10.10.10.10:101
Configure RT for vrf2
VTEP3(config-vrf)#route-target both 10.10.10.10:102
Configure RT for vrf2
VTEP3(config-vrf)#bfd interval 3 minrx 3 multiplier 3
Enable EVPN VXLAN multihoming
VTEP3(config)#evpn vxlan multihoming enable
Enable statistics on VXLAN tunnel interface
VTEP3(config)#nvo vxlan enable
Enable VXLAN
VTEP3(config)#qos enable
Enable qos
VTEP3(config)#qos statistics
Enable qos statistics
VTEP3(config)#bridge 1 protocol ieee vlan-bridge
Configure IEEE VLAN bridge
VTEP3(config)#no bridge 1 spanning-tree enable
Disable spanning tree in bridge 1 globally
VTEP3(config)#no igmp snooping
Disable igmp snooping messages globally
VTEP3(config)#vlan database
Enter into the VLAN database
VTEP3(config-vlan)#vlan 10-200 bridge 1 state enable
Configure VLAN 10-200 and associate with bridge 1
VTEP3(config-vlan)#interface lo
Enter lo interface mode
VTEP3(config-if)#ip address 6.6.6.6/32 secondary
Assign loopback IP
VTEP3(config-if)#interface vlan1.80
Specify interface VLAN1.80 to be configured.
VTEP3(config-if)#ip address 56.1.1.2/24
Assign IP address
VTEP3(config-if)#ip ospf cost 1
Change OSPF cost of the link
VTEP3(config-if)#interface vlan1.90
Specify interface VLAN1.90 to be configured.
VTEP3(config-if)#ip address 46.1.1.2/24
Assign IP address
VTEP3(config-if)#ip ospf cost 1
Change OSPF cost of the link
VTEP3(config-if)#interface xe3
Enter interface mode
VTEP3(config-if)#switchport
Set the interface as Layer2 port
VTEP3(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
VTEP3(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
VTEP3(config-if)#switchport trunk allowed vlan add 90,99
Enable VLAN's allowed on this interface.
VTEP3(config-if)#switchport trunk native vlan 99
Configure native VLAN
VTEP3(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP3(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
VTEP3(config-if)#interface xe15
Enter interface mode
VTEP3(config-if)#switchport
Set the interface as Layer2 port
VTEP3(config-if)#bridge-group 1 spanning-tree disable
Associate the interface with bridge group 1 and disable spanning tree
VTEP3(config-if)#switchport mode trunk
Set the switching characteristics of this interface to trunk mode.
VTEP3(config-if)#switchport trunk allowed vlan add 80,89
Enable VLAN's allowed on this interface.
VTEP3(config-if)#switchport trunk native vlan 89
Configure native VLAN
VTEP3(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP3(config-if)#mtu 1600
Change interface mtu value
VTEP3(config-if)#spanning-tree edgeport
Set the port as an edge-port to enable rapid transitions
VTEP3(config-if)#interface xe45
Enter interface mode
VTEP3(config-if)#switchport
Set the interface as Layer2 port
VTEP3(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP3(config-if)#interface xe46
Enter interface mode
VTEP3(config-if)#switchport
Set the interface as Layer2 port
VTEP3(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
VTEP3(config-if)#router ospf 1
Enter OSPF configuration mode
VTEP3(config-router)#ospf router-id 6.6.6.6
Configure OSPF router id
VTEP3(config-router)#bfd all-interfaces
Enable BFD in all OSPF interfaces
VTEP3(config-router)#network 6.6.6.6/32 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP3(config-router)#network 46.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP3(config-router)#network 56.1.1.0/24 area 0.0.0.0
Define the Network on which OSPF runs and associate the area ID (area 0) with the interface.
VTEP3(config-router)#router bgp 100
Enter address-family IPv4 unicast mode
VTEP3(config-router)#address-family ipv4 unicast
Add the lo network to BGP route
VTEP3(config-router)#network 6.6.6.6/32
Activate neighbors
VTEP3(config-router-af)#neighbor 1.1.1.1 activate
Activate neigbors
VTEP3(config-router-af)#neighbor 2.2.2.2 activate
Exit address-family mode.
VTEP3(config-router-af)#exit-address-family
Enter Router BGP mode and define the AS number 100.
VTEP3(config-router)#neighbor 1.1.1.1 remote-as 100
Configure BGP remote-as 100 with neighbor IP
VTEP3(config-router)#neighbor 1.1.1.1 update-source lo
Define BGP neighbors, to update the source routes with lo
VTEP3(config-router)#neighbor 2.2.2.2 remote-as 100
Configure BGP remote-as 100 with neighbor IP
VTEP3(config-router)#neighbor 2.2.2.2 update-source lo
Configure advertisement-interval as 0 for fast convergence for VTEP2
(config-router)#neighbor 2.2.2.2 advertisement-interval 0
Configure advertisement-interval as 0 for fast convergence for VTEP1
(config-router)#neighbor 1.1.1.1 advertisement-interval 0
Define BGP neighbors, to update the source routes with lo
VTEP3(config-router)#address-family l2vpn evpn
Enter in to BGP L2VPN EVPN address-family
VTEP3(config-router-af)#neighbor 1.1.1.1 activate
Activate neigbors
VTEP3(config-router-af)#neighbor 2.2.2.2 activate
Activate neigbors
VTEP3(config-router-af)#exit-address-family
Exit from BGP L2VPN EVPN address-family
VTEP3(config-router)#nvo vxlan vtep-ip-global 6.6.6.6
Configure VXLAN global IP
VTEP3(config)#nvo vxlan id 1 ingress-replication inner-vid-disabled
Create VNID 1
VTEP3(config-nvo)#vxlan host-reachability-protocol evpn-bgp vrf1
Associate VNID with EVPN and vrf1
VTEP3(config-nvo)#nvo vxlan id 1000 ingress-replication inner-vid-disabled
Create VNID 1000
VTEP3(config-nvo)#vxlan host-reachability-protocol evpn-bgp vrf2
Associate VNID with EVPN and vrf2
VTEP3(config-nvo)#nvo vxlan access-if port-vlan xe45 3001
Create VXLAN access port port-VLAN
VTEP3(config-nvo-acc-if)#map vnid 1
Map the VNID to access-if
VTEP3(config-nvo-acc-if)#nvo vxlan access-if port xe46
Create VXLAN access port
VTEP3(config-nvo-acc-if)#map vnid 1000
Map the VNID to access-if
VTEP3(config-nvo-acc-if)#commit
Commit the candidate configuration to the running configuration
SWITCH
 
SWITCH#configure terminal
Enter configuration terminal
SWITCH#(config)# bridge 1 protocol rstp vlan-bridge
Configure rstp vlan bridge
SWITCH#(config-vlan)#interface po1
Enter interface mode
SWITCH#(config-if)#switchport
Set the interface as Layer2 port
SWITCH#(config-if)#load-interval 30
Configure load period in multiple of 30 seconds
SWITCH#(config-if)#interface ce9/1
Enter interface mode
SWITCH#(config-if)#channel-group 1 mode active
Map this interface to po1
SWITCH#(config-if)#interface ce9/2
Enter interface mode
SWITCH#(config-if)#channel-group 1 mode active
Map this interface to po1
SWITCH#(config-if)#interface ce10/1
Enter interface mode
SWITCH#(config-if)#channel-group 1 mode active
Map this interface to po1
SWITCH#(config-if)#interface ce10/2
Enter interface mode
SWITCH#(config-if)#channel-group 1 mode active
Map this interface to po1
SWITCH#(config-if)#interface ce31/1
Set the port as an edge-port to enable rapid transitions
SWITCH#(config-if)#switchport
Enter interface mode
SWITCH#(config-if)#bridge-group 1 spanning-tree disable
Set the interface as Layer2 port
SWITCH#(config-if)#switchport mode trunk
Associate the interface with bridge group 1 and disable spanning tree
SWITCH#(config-if)#switchport trunk allowed vlan all
Set the switching characteristics of this interface to trunk mode.
SWITCH#(config-if)#load-interval 30
Configure native VLAN
SWITCH#(config-if)#commit
Commit the candidate configuration to the running configuration
Validation
VTEP1#sh ip ospf neighbor
 
Total number of full neighbors: 3
OSPF process 1 VRF(default):
Neighbor ID Pri State Dead Time Address Interface Instance ID
2.2.2.2 1 Full/DR 00:00:30 12.1.1.2 vlan1.10 0
3.3.3.3 1 Full/DR 00:00:31 13.1.1.2 vlan1.20 0
4.4.4.4 1 Full/DR 00:00:33 14.1.1.2 vlan1.30 0
 
 
VTEP2#sh ip ospf neighbor
 
Total number of full neighbors: 3
OSPF process 1 VRF(default):
Neighbor ID Pri State Dead Time Address Interface Instance ID
1.1.1.1 1 Full/Backup 00:00:38 12.1.1.1 vlan1.10 0
3.3.3.3 1 Full/DR 00:00:39 23.1.1.2 vlan1.40 0
4.4.4.4 1 Full/DR 00:00:39 24.1.1.2 vlan1.50 0
P1#sh ip ospf neighbor
 
Total number of full neighbors: 4
OSPF process 1 VRF(default):
Neighbor ID Pri State Dead Time Address Interface Instance ID
1.1.1.1 1 Full/Backup 00:00:39 13.1.1.1 vlan1.20 0
2.2.2.2 1 Full/Backup 00:00:38 23.1.1.1 vlan1.40 0
4.4.4.4 1 Full/DR 00:00:40 34.1.1.2 vlan1.100 0
5.5.5.5 1 Full/DR 00:00:36 35.1.1.2 vlan1.60 0
 
P2#sh ip ospf neighbor
 
Total number of full neighbors: 5
OSPF process 1 VRF(default):
Neighbor ID Pri State Dead Time Address Interface Instance ID
1.1.1.1 1 Full/Backup 00:00:30 14.1.1.1 vlan1.30 0
2.2.2.2 1 Full/Backup 00:00:38 24.1.1.1 vlan1.50 0
3.3.3.3 1 Full/Backup 00:00:33 34.1.1.1 vlan1.100 0
5.5.5.5 1 Full/DR 00:00:30 45.1.1.2 vlan1.70 0
6.6.6.6 1 Full/DR 00:00:34 46.1.1.2 vlan1.90 0
P2#
P3#sh ip ospf neighbor
 
Total number of full neighbors: 3
OSPF process 1 VRF(default):
Neighbor ID Pri State Dead Time Address Interface Instance ID
3.3.3.3 1 Full/Backup 00:00:34 35.1.1.1 vlan1.60 0
4.4.4.4 1 Full/Backup 00:00:34 45.1.1.1 vlan1.70 0
6.6.6.6 1 Full/DR 00:00:33 56.1.1.2 vlan1.80 0
P3#
 
VTEP1#sh bgp l2vpn evpn summary
BGP router identifier 1.1.1.1, local AS number 100
BGP table version is 4
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd AD MACIP MCAST ESI PREFIX-ROUTE
2.2.2.2 4 100 23 22 4 0 0 00:07:34 2 0 0 2 0 0
6.6.6.6 4 100 21 22 4 0 0 00:07:34 2 0 0 2 0 0
 
Total number of neighbors 2
 
Total number of Established sessions 2
VTEP1#
VTEP2#sh bgp l2vpn evpn summary
BGP router identifier 2.2.2.2, local AS number 100
BGP table version is 5
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd AD MACIP MCAST ESI PREFIX-ROUTE
1.1.1.1 4 100 22 24 5 0 0 00:07:41 2 0 0 2 0 0
6.6.6.6 4 100 24 27 5 0 0 00:08:51 2 0 0 2 0 0
 
Total number of neighbors 2
 
Total number of Established sessions 2
VTEP2#
VTEP3#sh bgp l2vpn evpn summary
BGP router identifier 6.6.6.6, local AS number 100
BGP table version is 5
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd AD MACIP MCAST ESI PREFIX-ROUTE
1.1.1.1 4 100 23 21 5 0 0 00:07:44 2 0 0 2 0 0
2.2.2.2 4 100 26 24 5 0 0 00:08:54 2 0 0 2 0 0
 
Total number of neighbors 2
 
Total number of Established sessions 2
VTEP3#
 
VTEP1#show nvo vxlan mac-table
=====================================================================================================================================================
VXLAN MAC Entries
=====================================================================================================================================================
VNID Interface VlanId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status AccessPortDesc
_____________________________________________________________________________________________________________________________________________________
 
1 po1 1000 ---- 0000.1111.1111 00:aa:22:33:44:55:66:00:00:00 Static Local ------- -------
1 po1 1000 ---- 0000.1111.1112 00:aa:22:33:44:55:66:00:00:00 Static Local ------- -------
1 po1 1000 ---- 0000.1111.1113 00:aa:22:33:44:55:66:00:00:00 Static Local ------- -------
1 po1 1000 ---- 0000.1111.1114 00:aa:22:33:44:55:66:00:00:00 Static Local ------- -------
1 po1 1000 ---- 0000.1111.1115 00:aa:22:33:44:55:66:00:00:00 Static Local ------- -------
1 po1 1000 ---- a82b.b57c.4470 00:aa:22:33:44:55:66:00:00:00 Dynamic Local ------- -------
1000 ---- ---- ---- a82b.b57c.4476 00:aa:22:33:44:55:66:00:00:00 Dynamic Remote ------- -------
 
Total number of entries are : 7
 
VTEP1#
VTEP2#sh nvo vxlan mac-table
=====================================================================================================================================================
VXLAN MAC Entries
=====================================================================================================================================================
VNID Interface VlanId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status AccessPortDesc
_____________________________________________________________________________________________________________________________________________________
 
1 ---- ---- ---- 0000.1111.1111 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- 0000.1111.1112 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- 0000.1111.1113 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- 0000.1111.1114 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- 0000.1111.1115 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- a82b.b57c.4470 00:aa:22:33:44:55:66:00:00:00 Dynamic Remote ------- -------
1000 po1 2000 ---- a82b.b57c.4476 00:aa:22:33:44:55:66:00:00:00 Dynamic Local ------- -------
 
Total number of entries are : 7
 
VTEP2#
VTEP3#sh nvo vxlan mac-table
=====================================================================================================================================================
VXLAN MAC Entries
=====================================================================================================================================================
VNID Interface VlanId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status AccessPortDesc
_____________________________________________________________________________________________________________________________________________________
 
1 ---- ---- ---- 0000.1111.1111 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- 0000.1111.1112 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- 0000.1111.1113 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- 0000.1111.1114 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- 0000.1111.1115 00:aa:22:33:44:55:66:00:00:00 Static Remote ------- -------
1 ---- ---- ---- a82b.b57c.4470 00:aa:22:33:44:55:66:00:00:00 Dynamic Remote ------- -------
1000 ---- ---- ---- a82b.b57c.4476 00:aa:22:33:44:55:66:00:00:00 Dynamic Remote ------- -------
 
Total number of entries are : 7
 
VTEP3#
VTEP1#show nvo vxlan access-if brief
 
Inner Admin Link
Interface Vlan vlan Ifindex Vnid status status
-----------------------------------------------------------
xe46 --- --- 500000 1 up up
po1 2000 --- 500001 1000 up up
po1 2001 --- 500002 1000 up up
 
 
Total number of entries are 2
VTEP1#
VTEP2#show nvo vxlan access-if brief
 
Inner Admin Link
Interface Vlan vlan Ifindex Vnid status status
-----------------------------------------------------------
xe47 --- --- 500000 1 up up
po1 2001 --- 500001 1000 up up
po1 2000 --- 500002 1000 up up
 
Total number of entries are 3
VTEP2#
VTEP3#show nvo vxlan access-if brief
 
Inner Admin Link
Interface Vlan vlan Ifindex Vnid status status
-----------------------------------------------------------
xe45 3001 --- 500000 1 up up
xe46 --- --- 500001 1000 up up
 
Total number of entries are 2
VTEP3#
VTEP1#sh nvo vxlan tunnel
VXLAN Network tunnel Entries
Source Destination Status Up/Down Update
====================================================================================
1.1.1.1 6.6.6.6 Installed 00:03:59 00:03:59
1.1.1.1 2.2.2.2 Installed 00:03:59 00:03:59
 
Total number of entries are 2
VTEP1#sh nvo vxlan
VXLAN Information
=================
Codes: NW - Network Port
AC - Access Port
(u) - Untagged
 
VNID VNI-Name VNI-Type Type Interface ESI VLAN DF-Status Src-Addr Dst-Addr
_______________________________________________________________________________________________________________________________
1 ---- L2 NW ---- ---- ---- ---- 1.1.1.1 6.6.6.6
1 ---- L2 NW ---- ---- ---- ---- 1.1.1.1 2.2.2.2
1000 ---- -- AC po1 --- 00:aa:22:33:44:55:66:00:00:00 2000 DF ---- ----
1000 ---- -- AC po1 --- 00:aa:22:33:44:55:66:00:00:00 2001 DF ---- ----
1000 ---- L2 NW ---- ---- ---- ---- 1.1.1.1 6.6.6.6
1000 ---- L2 NW ---- ---- ---- ---- 1.1.1.1 2.2.2.2
1000 ---- -- AC xe46 --- Single Homed Port --- ---- ---- ---- ----
 
Total number of entries are 10
VTEP1#
 
VTEP2#sh nvo vxlan tunnel
VXLAN Network tunnel Entries
Source Destination Status Up/Down Update
====================================================================================
2.2.2.2 1.1.1.1 Installed 00:03:59 00:03:59
2.2.2.2 6.6.6.6 Installed 00:05:09 00:05:09
 
Total number of entries are 2
VTEP2#sh nvo vxlan
VXLAN Information
=================
Codes: NW - Network Port
AC - Access Port
(u) - Untagged
 
VNID VNI-Name VNI-Type Type Interface ESI VLAN DF-Status Src-Addr Dst-Addr
_______________________________________________________________________________________________________________________________
1 ---- L2 NW ---- ---- ---- ---- 2.2.2.2 1.1.1.1
1 ---- L2 NW ---- ---- ---- ---- 2.2.2.2 6.6.6.6
1 ---- -- AC xe47 --- Single Homed Port --- ---- ---- ---- ----
1000 ---- L2 NW ---- ---- ---- ---- 2.2.2.2 1.1.1.1
1000 ---- L2 NW ---- ---- ---- ---- 2.2.2.2 6.6.6.6
1000 ---- -- AC po1 --- 00:aa:22:33:44:55:66:00:00:00 2001 NON-DF ---- ----
1000 ---- -- AC po1 --- 00:aa:22:33:44:55:66:00:00:00 2000 NON-DF ---- ----
 
Total number of entries are 11
VTEP2#
 
VTEP3#sh nvo vxlan tunnel
VXLAN Network tunnel Entries
Source Destination Status Up/Down Update
====================================================================================
6.6.6.6 1.1.1.1 Installed 00:03:58 00:03:58
6.6.6.6 2.2.2.2 Installed 00:05:08 00:04:03
 
Total number of entries are 2
VTEP3#sh nvo vxlan
VXLAN Information
=================
Codes: NW - Network Port
AC - Access Port
(u) - Untagged
 
VNID VNI-Name VNI-Type Type Interface ESI VLAN DF-Status Src-Addr Dst-Addr
_______________________________________________________________________________________________________________________________
1 ---- L2 NW ---- ---- ---- ---- 6.6.6.6 1.1.1.1
1 ---- L2 NW ---- ---- ---- ---- 6.6.6.6 2.2.2.2
1 ---- -- AC xe45 --- Single Hommed port --- 3001 ---- ---- ----
1000 ---- L2 NW ---- ---- ---- ---- 6.6.6.6 1.1.1.1
1000 ---- L2 NW ---- ---- ---- ---- 6.6.6.6 2.2.2.2
1000 ---- -- AC xe46 --- Single Homed Port --- ---- ---- ---- ----
 
Total number of entries are 10
VTEP3#