LDP-VPLS Service Mapping Configuration
Overview
This chapter includes step-by-step configurations for LDP VPLS. It also contains an overview of the concepts of LDP VPLS. Virtual Private LAN Service (VPLS) is a way to provide Ethernet-based multipoint-to-multipoint communication over IP- MPLS networks. It allows geographically-dispersed sites to share an Ethernet broadcast domain by connecting sites through pseudowires.
Topology
The diagram depicts the topology for the configuration examples that follow.
LDP-VPLS service mappring
Configuration
PE1: Loopback Interface
#configure terminal | Enter configuration mode. |
(config)#interface lo | Enter the Interface mode for the loopback interface. |
(config-if)#ip address 21.21.21.21/32 secondary | Configure IP address on loopback interface. |
(config-if)#exit | Exit interface mode |
PE1: Global LDP
(config)#router ldp | Enter the Router LDP mode. |
(config-router)#router-id 21.21.21.21 | Set the router ID to IP address 21.21.21.21 |
(config-router)#transport-address ipv4 21.21.21.21 | Configure transport address |
(config-router)#targeted-peer ipv4 23.23.23.23 | Configure targeted peer |
(config-router)#targeted-peer #commit | Commit candidate configuration to the running configuration |
(config-router-targeted-peer)#end | Exit from router target peer and LDP mode |
PE1: Interface Configuration
#configure terminal | Enter configuration mode |
(config)#interface xe2 | Enter the Interface mode for xe2. |
(config-if)# ip address 10.10.23.21/24 | Configure IP address on the interface. |
(config-if)#enable-ldp ipv4 | Enable LDP on the physical interface |
(config-if)# label-switching | Enable label switching on the interface. |
(config-if)#exit | Exit interface mode |
PE1: OSPF Configuration
(config)#router ospf 100 | Enter the Router OSPF mode. |
(config-router)#ospf router-id 21.21.21.21 | Router-id configurations |
(config-router)#network 21.21.21.21/32 area 0 | Advertise loopback address in OSPF. |
(config-router)#network 10.10.23.0/24 area 0 | Advertise network address in OSPF. |
(config-router)#exit | Exit Router OSPF mode and return to Configure mode. |
PE1: LDP VPLS Configuration
(config)#mpls vpls v1 25 | Enter VPLS config mode |
(config-vpls)#service-tpid dot1.ad | Service tp-id configuration. |
(config-vpls)#signaling ldp | Define Signaling as LDP |
(config-vpls-sig)#vpls-type vlan | Type VLAN configuration for VPLS |
(config-vpls-sig)#vpls-peer 23.23.23.23 | Configure VPLS Peer |
(config-vpls-sig)#exit-signaling | Exit Signaling LDP mode |
(config-vpls)#exit | Exit VPLS mode |
(config)#mpls vpls v2 26 | Enter VPLS config mode |
(config-vpls)#service-tpid dot1.ad | Service tp-id configuration. |
(config-vpls)#signaling ldp | Define Signaling as LDP |
(config-vpls-sig)#vpls-type vlan | Type VLAN configuration for VPLS |
(config-vpls-sig)#vpls-peer 23.23.23.23 | Configure VPLS Peer |
(config-vpls-sig)#exit-signaling | Exit Signaling LDP mode |
(config-vpls)#exit | Exit VPLS mode |
(config)#mpls vpls v3 27 | Enter VPLS config mode |
(config-vpls)#signaling ldp | Define Signaling as LDP |
(config-vpls-sig)#vpls-type vlan | Type VLAN configuration for VPLS |
(config-vpls-sig)#vpls-peer 23.23.23.23 | Configure VPLS Peer |
(config-vpls-sig)# exit-signaling | Exit Signaling LDP mode |
(config-vpls)#exit | Exit VPLS mode |
(config)#mpls vpls v4 28 | Enter VPLS config mode |
(config-vpls)#signaling ldp | Define Signaling as LDP |
(config-vpls-sig)#vpls-type vlan | Type VLAN configuration for VPLS |
(config-vpls-sig)#vpls-peer 23.23.23.23 | Configure VPLS Peer |
(config-vpls-sig)# exit-signaling | Exit Signaling LDP mode |
(config-vpls)#exit | Exit VPLS mode |
(config)#commit | Commit candidate configuration to the running configuration |
P: Loopback Interface
#configure terminal | Enter configuration mode. |
(config)#interface lo | Enter the Interface mode for the loopback interface. |
(config-if)#ip address 22.22.22.22/32 secondary | Configure IP address on loopback interface. |
(config-if)#exit | Exit interface mode |
P: Global LDP
(config)#router ldp | Enter the Router LDP mode. |
(config-router)#router-id 22.22.22.22 | Set the router ID to IP address 22.22.22.22 |
(config-router)#transport-address ipv4 22.22.22.22 | Configure transport address |
(config-router)#commit | Commit candidate configuration to the running configuration |
(config-router-targeted-peer)#end | Exit from router target peer and LDP mode |
P: Interface Configuration
#configure terminal | Enter configuration mode |
(config)#interface xe1 | Enter the Interface mode for xe1. |
(config-if)# ip address 10.10.23.22/24 | Configure IP address on the interface. |
(config-if)#enable-ldp ipv4 | Enable LDP on the physical interface |
(config-if)# label-switching | Enable label switching on the interface. |
(config-if)#exit | Exit interface mode |
(config)#interface xe2 | Enter the Interface mode for xe2. |
(config-if)# ip address 10.10.21.22/24 | Configure IP address on the interface. |
(config-if)#enable-ldp ipv4 | Enable LDP on the physical interface |
(config-if)# label-switching | Enable label switching on the interface. |
(config-if)#exit | Exit interface mode |
P: OSPF Configuration
(config)#router ospf 100 | Enter the Router OSPF mode. |
(config-router)#network 22.22.22.22/32 area 0 | Advertise loopback address in OSPF. |
(config-router)#network 10.10.23.0/24 area 0 | Advertise network address in OSPF. |
(config-router)#network 10.10.21.0/24 area 0 | Advertise network address in OSPF. |
(config-router)#exit | Exit Router OSPF mode and return to Configure mode. |
(config)#commit | Commit candidate configuration to the running configuration |
PE2: Loopback Interface
#configure terminal | Enter configuration mode. |
(config)#interface lo | Enter the Interface mode for the loopback interface. |
(config-if)#ip address 23.23.23.23/32 secondary | Configure IP address on loopback interface. |
(config-if)#exit | Exit interface mode |
PE2: Global LDP
(config)#router ldp | Enter the Router LDP mode. |
(config-router)#router-id 23.23.23.23 | Set the router ID to IP address 23.23.23.23 |
(config-router)#transport-address ipv4 23.23.23.23 | Configure transport address |
(config-router)#targeted-peer ipv4 21.21.21.21 | Configure targeted peer |
(config-router-targeted-peer)#commit | Commit candidate configuration to the running configuration |
(config-router-targeted-peer)#end | Exit from router target peer and LDP mode |
PE2: Interface Configuration
#configure terminal | Enter configuration mode. |
(config)#interface xe1 | Enter the Interface mode for xe1. |
(config-if)# ip address 10.10.21.23/24 | Configure IP address on the interface. |
(config-if)#enable-ldp ipv4 | Enable LDP on the physical interface |
(config-if)# label-switching | Enable label switching on the interface. |
(config-if)#exit | Exit interface mode |
PE2: OSPF Configuration
(config)#router ospf 100 | Enter the Router OSPF mode. |
(config-router)#network 23.23.23.23/32 area 0 | Advertise loopback address in OSPF. |
(config-router)#network 10.10.21.0/24 area 0 | Advertise network address in OSPF. |
(config-router)#exit | Exit Router OSPF mode and return to Configure mode. |
PE2: LDP VPLS Configuration
(config)#mpls vpls v1 25 | Enter VPLS config mode |
(config-vpls)#service-tpid dot1.ad | Service tp-id configuration. |
(config-vpls)#signaling ldp | Define Signaling as LDP |
(config-vpls-sig)#vpls-type vlan | Type VLAN configuration for VPLS |
(config-vpls-sig)#vpls-peer 21.21.21.21 | Configure VPLS Peer |
(config-vpls-sig)# exit-signaling | Exit Signaling LDP mode |
(config-vpls)#exit | Exit VPLS mode |
(config)#mpls vpls v2 26 | Enter VPLS config mode |
(config-vpls)#service-tpid dot1.ad | Service tp-id configuration. |
(config-vpls)#signaling ldp | Define Signaling as LDP |
(config-vpls-sig)#vpls-type vlan | Type VLAN configuration for VPLS |
(config-vpls-sig)#vpls-peer 21.21.21.21 | Configure VPLS Peer |
(config-vpls-sig)# exit-signaling | Exit Signaling LDP mode |
(config-vpls)#exit | Exit VPLS mode |
(config)#mpls vpls v3 27 | Enter VPLS config mode |
(config-vpls)#signaling ldp | Define Signaling as LDP |
(config-vpls-sig)#vpls-type vlan | Type VLAN configuration for VPLS |
(config-vpls-sig)#vpls-peer 21.21.21.21 | Configure VPLS Peer |
(config-vpls-sig)# exit-signaling | Exit Signaling LDP mode |
(config-vpls)#exit | Exit VPLS mode |
(config)#mpls vpls v4 28 | Enter VPLS config mode |
(config-vpls)#signaling ldp | Define Signaling as LDP |
(config-vpls-sig)#vpls-type vlan | Type VLAN configuration for VPLS |
(config-vpls-sig)#vpls-peer 21.21.21.21 | Configure VPLS Peer |
(config-vpls-sig)# exit-signaling | Exit Signaling LDP mode |
(config-vpls)#exit | Exit VPLS mode |
(config)#commit | Commit candidate configuration to the running configuration |
LDP VPLS Service Mapping Configuration
PE1: POP
#configure terminal | Configure mode |
(config)#service-template template1 | Template configuration |
(config-svc)# match double-tag outer-vlan 2024 inner-vlan 2023 | Match criteria under template configuration |
(config-svc)# rewrite ingress pop outgoing-tpid dot1.q | Action to be performed for the match. |
(config-svc)#exit | Exit template configuration mode |
PE1: XLATE
(config)#service-template template2 | Template configuration |
(config-svc)# match double-tag outer-vlan 2030 inner-vlan 2024 | Match criteria under template configuration |
(config-svc)# rewrite ingress translate 2026 outgoing-tpid dot1.q | Action to be performed for the match |
(config-svc)#exit | Exit template configuration mode |
PE1: PUSH
(config)#service-template template3 | Template configuration |
(config-svc)# match outer-vlan 500 | Match criteria under template configuration |
(config-svc)# rewrite ingress push 300 | Action to be performed for the default match. |
(config-svc)#exit | Exit template configuration mode |
PE1: PUSH-service-template with multiple match support
This is to validate the multiple match criteria support in a service template. When multiple match statements are configured only rewrite push is supported, rewrite translate and pop are not supported.
(config)#service-template template4 | Template configuration |
(config-svc)# match outer-vlan 700 | Allow VLAN 700 traffic on this VC |
(config-svc)# match double-tag outer-vlan 1200 inner-vlan 3200 | Allow double tag match with s+c tags |
(config-svc)# match untagged | Allow untagged traffic |
(config-svc)# rewrite ingress push 300 | Push Action performed for service template |
(config-svc)#exit | Exit configure SVC mode |
PE1: Access port Configuration
(config)#interface xe1 | Enter the Interface mode for xe1. |
(config-if)#switchport | Configure interface as a layer 2 port. |
(config-if)#mpls-vpls v1 service-template template1 | Bind the VPLS to the Access Interface. |
(config-if-vpls)#exit | Exit VPLS attachment-circuit mode |
(config-if)#mpls-vpls v2 service-template template2 | Bind the VPLS to the Access Interface. |
(config-if-vpls)#exit | Exit VPLS attachment-circuit mode |
(config-if)#mpls-vpls v3 service-template template3 | Bind the VPLS to the Access Interface. |
(config-if-vpls)#exit | Exit VPLS attachment-circuit mode |
(config-if)#mpls-vpls v4 service-template template4 | Bind the VPLS to the Access Interface. |
(config-if-vpls)#split-horizon group access1 | Configure split-horizon group on VPLS |
(config-if-vpls)#exit | Exit VPLS attachment-circuit mode |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)#commit | Commit candidate configuration to the running configuration |
PE2: POP
#configure terminal | Configure mode |
(config)#service-template template1 | Template configuration |
(config-svc)# match double-tag outer-vlan 2024 inner-vlan 2023 | Match criteria under template configuration |
(config-svc)# rewrite ingress pop outgoing-tpid dot1.q | Action to be performed for the match. |
(config-svc)#exit | Exit template configuration mode |
PE2: XLATE
(config)#service-template template2 | Template configuration |
(config-svc)# match double-tag outer-vlan 2030 inner-vlan 2024 | Match criteria under template configuration |
(config-svc)# rewrite ingress translate 2026 outgoing-tpid dot1.q | Action to be performed for the match |
(config-svc)#exit | Exit template configuration mode |
PE2: PUSH
(config)#service-template template3 | Template configuration |
(config-svc)# match outer-vlan 500 | Match criteria under template configuration |
(config-svc)# rewrite ingress push 300 | Action to be performed for the default match. |
(config-svc)#exit | Exit template configuration mode |
PE2: PUSH-service-template with multiple match
This is to validate the multiple match criteria support in a service template. When multiple match statements are configured only rewrite push is supported, rewrite translate and pop are not supported.
(config)#service-template template4 | Template configuration |
(config-svc)# match outer-vlan 700 | Allow VLAN 700 traffic on this VC |
(config-svc)# match double-tag outer-vlan 1200 inner-vlan 3200 | Allow double tag match with s+c tags |
(config-svc)# match untagged | Allow untagged traffic |
(config-svc)# rewrite ingress push 300 | Push Action performed for service template |
(config-svc)#exit | Exit configure SVC mode |
PE2: Access port Configuration
(config)#interface xe2 | Enter the Interface mode for xe2. |
(config-if)#switchport | Configure interface as a layer 2 port. |
(config-if)#mpls-vpls v1 service-template template1 | Bind the VPLS to the Access Interface. |
(config-if-vpls)#exit | Exit VPLS attachment-circuit mode |
(config-if)#mpls-vpls v2 service-template template2 | Bind the VPLS to the Access Interface. |
(config-if-vpls)#exit | Exit VPLS attachment-circuit mode |
(config-if)#mpls-vpls v3 service-template template3 | Bind the VPLS to the Access Interface. |
(config-if-vpls)#exit | Exit VPLS attachment-circuit mode |
(config-if)#mpls-vpls v4 service-template template4 | Bind the VPLS to the Access Interface. |
(config-if-vpls)#split-horizon group access1 | Configure split-horizon group on VPLS |
(config-if-vpls)#exit | Exit VPLS attachment-circuit mode |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)#commit | Commit candidate configuration to the running configuration |
Validation
show mpls vpls mesh
VPLS-ID Peer Addr Tunnel-Label In-Label Network-Intf Out-Label Lkps/St PW-INDEX SIG-Protocol Status Ecmp-Group
25 23.23.23.23 24320 24322 xe2 24320 2/Up 1 LDP Active N/A
26 23.23.23.23 24320 24320 xe2 24321 2/Up 2 LDP Active N/A
27 23.23.23.23 24320 24321 xe2 24322 2/Up 3 LDP Active N/A
28 23.23.23.23 24320 24323 xe2 24324 2/Up 3 LDP Active N/A
#show ldp vpls
VPLS-ID Peer Address State Type Label-Sent Label-Rcvd
25 23.23.23.23 Up vlan 24322 24320
26 23.23.23.23 Up vlan 24320 24321
27 23.23.23.23 Up vlan 24321 24322
28 23.23.23.23 Up vlan 24323 24324
#show ldp vpls detail
VPLS Identifier : 25
Peer IP : 23.23.23.23
VC State : UP
VC Type : vlan
VC Label Sent : 24322
VC Label Received : 24320
VPLS Identifier : 26
Peer IP : 23.23.23.23
VC State : UP
VC Type : vlan
VC Label Sent : 24320
VC Label Received : 24321
VPLS Identifier : 27
Peer IP : 23.23.23.23
VC State : UP
VC Type : vlan
VC Label Sent : 24321
VC Label Received : 24322
VPLS Identifier : 28
Peer IP : 23.23.23.23
VC State : UP
VC Type : vlan
VC Label Sent : 24323
VC Label Received : 24324
#show mpls vpls detail
Virtual Private LAN Service Instance: v1, ID: 25
SIG-Protocol: LDP
Attachment-Circuit :UP
Learning: Enabled
Group ID: 0, VPLS Type: Ethernet VLAN, Configured MTU: 1500
Description: none
service-tpid: dot1.ad
Operating mode: Tagged
Svlan Id: 0
Svlan Tpid: 88a8
Configured interfaces:
Interface: xe1
Service-template : template1
Match criteria : 2024/2023
Mesh Peers:
23.23.23.23 (Up)
Virtual Private LAN Service Instance: v2, ID: 26
SIG-Protocol: LDP
Attachment-Circuit :UP
Learning: Enabled
Group ID: 0, VPLS Type: Ethernet VLAN, Configured MTU: 1500
Description: none
service-tpid: dot1.ad
Operating mode: Tagged
Svlan Id: 0
Svlan Tpid: 88a8
Configured interfaces:
Interface: xe1
Service-template : template2
Match criteria : 2030/2024
Action type : Translate
Action value : 2026
Outgoing tpid : dot1.q
Mesh Peers:
23.23.23.23 (Up)
Virtual Private LAN Service Instance: v3, ID: 27
SIG-Protocol: LDP
Attachment-Circuit :UP
Learning: Enabled
Group ID: 0, VPLS Type: Ethernet VLAN, Configured MTU: 1500
Description: none
service-tpid: dot1.q
Operating mode: Tagged
Svlan Id: 0
Svlan Tpid: 8100
Configured interfaces:
Interface: xe1
Service-template : template3
Match criteria : Accept all
Action type : Push
Action value : 300
Mesh Peers:
23.23.23.23 (Up)
Virtual Private LAN Service Instance: v4, ID: 28
SIG-Protocol: LDP
Attachment-Circuit :UP
Learning: Enabled
Group ID: 0, VPLS Type: Ethernet VLAN, Configured MTU: 1500
Description: none
service-tpid: dot1.q
Operating mode: Tagged
Svlan Id: 0
Svlan Tpid: 8100
Configured interfaces:
Interface: xe1
Service-template : template4
Match criteria : 700
1200/3200
Untagged
Action type : Push
Action value : 300
Mesh Peers:
23.23.23.23 (Up)