PTP G.8275.1 Profile Configuration
This chapter shows how to configure a PTP G.8275.1 profile over Ethernet, IPv4, and IPv6. You configure T-GM and boundary clock with more than one port.
Note: Enable G.8275.1 profile only on L3 interfaces and sub interfaces. When LAG is available configure the PTP on a LAG interface. However, in certain cases, L2-LAG-member interface is supported. For example, MLAG use cases.
Topology
Configuration Topology
In this example, SW1, SW2 and SW3 are running PTP. SW1 acting as T-GM and SW2, SW3 acting as boundary clock.
PTP G.8275.1 Profile Configuration
This section shows how to set up G.8275.1 profile.
SW2 (boundary clock)
#configure terminal | Enter Configure mode |
(config)#bridge 1 protocol mstp | Create bridge 1 as an MSTP bridge (this step is not mandatory, but is a good practice to avoid layer 2 loops) |
(config)#synce | Enter configure Synchronous Ethernet mode. |
(config-synce)#synchronization option 1 | Set the synchronization network type. |
(config-synce)#exit | Exit Synce mode |
(config)#interface eth1 | Configure interface eth1 |
(config-if)#switchport | Configure eth1 as Layer 2 port |
(config-if)#bridge-group 1 | Configure eth1 in bridge group 1 |
(config-if)#synce | Enter interface Synchronous Ethernet mode. |
(config-if-synce)#mode synchronous | Configure synchronous mode. |
(config-if-synce)#input-source 2 | Configure the interface as an input source with priority 2. |
(config-if-synce)#exit | Exit Port Configure mode |
(conig-if)#exit | Exit Interface mode |
(config)#interface eth2 | Configure interface eth2 |
(config-if)#switchport | Configure eth2 as Layer 2 port |
(config-if)#bridge-group 1 | Configure eth2 in bridge group 1 |
(config-if)#synce | Enter interface Synchronous Ethernet mode. |
(config-if-synce)#mode synchronous | Configure synchronous mode. |
(config-if-synce)#output-source | Configure the interface as an output source. |
(config-if-synce)#exit | Exit Port Configure mode |
(config-if)#exit | Exit interface mode |
(config)#ptp clock 0 profile g8275.1 | Enables G8275.1 for PTP time/phase telecom profile |
(config-ptp-clk)#number-ports 2 | Configure the number of PTP ports on the instance |
(config-ptp-clk)#clock-port 2 | Configure ptp port |
(config-clk-port)#network-interface eth2 | Configure underlying interface that is used by this PTP Port |
(config-clk-port)#exit | Exit ptp clock port mode |
(config-ptp-clk)#clock-port 1 | Configure ptp port |
(config-clk-port)#network-interface eth1 | Configure underlying interface that is used by this PTP Port |
(config-clk-port)#exit | Exit ptp clock port mode |
SW3 (Boundary clock)
#configure terminal | Enter Configure mode |
(config)#bridge 1 protocol mstp | Create bridge 1 as an MSTP bridge (this step is not mandatory, but is a good practice to avoid layer 2 loops) |
(config)#synce | Enter configure Synchronous Ethernet mode. |
(config-synce)#synchronization option 1 | Set the synchronization network type. |
(config-synce)#exit | Exit Synce mode |
(config)#interface eth2 | Configure interface eth2 |
(config-if)#switchport | Configure eth2 as Layer 2 port |
(config-if)#bridge-group 1 | Configure eth2 in bridge group 1 |
(config-if)#synce | Enter interface Synchronous Ethernet mode. |
(config-if-synce)#mode synchronous | Configure synchronous mode. |
(config-if-synce)#input-source 4 | Configure the interface as an input source with priority 4. |
(config-if-synce)#exit | Exit Port Configure mode |
(config-if)#exit | Exit interface mode |
(config)#ptp clock 0 profile g8275.1 | Enables G8275.1 for PTP time/phase telecom profile |
(config-ptp-clk)#number-ports 1 | Configure the number of PTP ports on the instance |
(config-clk-clk)#clock-port 1 | Configure ptp port |
(config-clk-port)#network-interface eth2 | Configure underlying interface that is used by this PTP Port |
(config-clk-port)#exit | Exit ptp clock port mode |
SW1 (T-GM)
#configure terminal | Enter Configure mode |
(config)#bridge 1 protocol mstp | Create bridge 1 as an MSTP bridge (this step is not mandatory, but is a good practice to avoid layer 2 loops) |
(config)#synce | Enter configure Synchronous Ethernet mode. |
(config-synce)#synchronization option 1 | Set the synchronization network type. |
(config-synce)#exit | Exit Synce mode |
(config)#synce-interface gps | Configure synce interface gps |
(config-synce-if)#mode synchronous | Configure synchronous mode |
(config-synce-if)#input-source 1 | Configure the interface as an input source with priority 1 |
(config-synce-if)#quality-level QL_PRC | Configure QL-value. |
(config-synce-if)#mode synchronous | Configure synchronous mode. |
(config-synce-if)#wait-to-restore 1 | Configure Wait-to-Restore timer. |
(config-synce-if)#exit | Exit Port Configure mode |
(config)#interface eth1 | Configure interface eth2 |
(config-if)#switchport | Configure eth2 as Layer 2 port |
(config-if)#bridge-group 1 | Configure eth2 in bridge group 1 |
(config-if)#synce | Enter interface Synchronous Ethernet mode. |
(config-if-synce)#mode synchronous | Configure synchronous mode. |
(config-if-synce)#output-source | Configure the interface as an output source. |
(config-if-synce)#exit | Exit Port Configure mode |
(config-if)#exit | Exit interface mode |
(config)#ptp clock 0 profile g8275.1 | Enables G8275.1 for PTP time/phase telecom profile |
(config-ptp-clk)#clock-type tgm | Enables clock type as T-GM |
(config-ptp-clk)#number-ports 2 | Configure the number of PTP ports on the instance |
(config-ptp-clk)#clock-port 2 | Configure ptp port |
(config-clk-port)#master-only | Configure the port as an master-only port |
(config-clk-port)#network-interface eth1 | Configure underlying interface that is used by this PTP Port |
(config-clk-port)#exit | Exit ptp clock port mode |
(config-ptp-clk)#clock-port 1 | Configure ptp port |
(config-clk-port)#network-interface gps | Configure underlying interface that is used by this PTP Port |
(config-clk-port)#exit | Exit ptp clock port mode |
Validation
SW2
1. Verify the default data set on SW2.
#sh ptp clock 0 dataset
Default Dataset:
Two Step Flag : No
Clock Identity : E8:C5:7A:FF:FE:23:6E:1C
Number Of Ports : 2
Priority1 : 128
Priority2 : 128
Slave Only : No
Local Priority : 128
Max Steps Removed : 255
Domain Number : 24
Clock Quality :
Clock Class : 248
Clock Accuracy : 254
Offset ScaledLogVariance : 65535
2. Verify the port state on SW2.
#show ptp clock 0 port
Port 1:
Port State : Slave
Port Identity : E8:C5:7A:FF:FE:23:6E:1C:00:01
Peer Mean Path Delay : 0
Log Announce Interval : -3
Log Min Delay Req Interval : -4
Log Sync Interval : -4
Announce Receipt Timeout : 3
Delay Mechanism : End to end
Version Number : 2
Local Priority : 128
Master only : False
Signal Fail : False
Network Interface : eth1
Vlan Configured :
Description :
Configured delay asymmetry : 0 nsec
Number of Foreign Masters : 1
Current Foreign Master : 0
Foreign Master #0
L2 Address : a0:00:00:00:00:01
Grandmaster clockIdentity : 00:00:00:00:00:00:00:01
Port ID : 00:00:00:00:00:00:00:01:00:01
clockClass : 6
Clock accuracy : 33
Offset scaled log variance : 65535
priority1 : 128
priority2 : 128
Steps removed : 0
PDV Scaled Allan Variance : 5
Received Packets : 46955
Discarded Packets : 4
Transmitted Packets : 19485
Drop Counters
Pkt rcvd on bad port state : 4
Peer #0
L2 Address : a0:00:00:00:00:01
Clock Identity : 00:00:00:00:00:00:00:01
Received Announce : 9392
Received Sync : 18784
Received Delay Response : 18781
Transmitted Delay Request : 18781
Port 2:
Port State : Master
Port Identity : E8:C5:7A:FF:FE:23:6E:1C:00:02
Peer Mean Path Delay : 0
Log Announce Interval : -3
Log Min Delay Req Interval : -4
Log Sync Interval : -4
Announce Receipt Timeout : 3
Delay Mechanism : End to end
Version Number : 2
Local Priority : 128
Master only : False
Signal Fail : False
Network Interface : eth2
Vlan Configured :
Description :
Configured delay asymmetry : 0 nsec
Received Packets : 18783
Discarded Packets : 0
Transmitted Packets : 47655
Peer #0
L2 Address : d0:00:00:00:00:01
Clock Identity : 00:00:00:00:00:00:00:02
Received Delay Request : 18786
Transmitted Announce : 9626
Transmitted Sync : 19251
Transmitted Delay Response : 18786
3. Verify the ptp servo on SW2.
#sh ptp servo
PTP servo status for clock 0
Servo Config : Phase Correction
Servo State : Normal Loop
Servo State Duration : 00:20:46
Servo APTS Mode : N/A
Frequency Correction : 0.000 ppb
Phase Correction : -3537.000 nsec
Offset From Master : -479.000 nsec
Mean Path Delay : 3536 nsec
APTS GPS to PTP Offset : 0 nsec
Sync Packet Rate : 16
Delay Packet Rate : 16
Note: Use show ptp stats to collect the PTP statistics and use clear ptp stats to clear the same.