OcNOS-SP : Segment Routing Guide : Segment Routing Configuration Guide : Topology-Independent Loop-Free Alternate
Topology-Independent Loop-Free Alternate
The term topology independent (TI) refers to the ability to provide a loop free backup path irrespective of the topologies used in the network. Topology-Independent Loop-Free Alternate (TI-LFA) uses segment routing to provide link, node and Shared Risk Link Groups (SRLG) protection in topologies where other fast reroute techniques, such as RLFA (Remote Loop Free Alternative) cannot provide protection. Currently, OSPF SR-TI-LFA supports only link protection.
The goal of TI-LFA is to reduce the packet loss that results while routers converge after a topology change due to a link failure. Rapid failure repair (up to 50msec) is achieved using pre-calculated backup paths that are loop-free.
Terminology
PLR : Point of Local Repair : The node that is just upstream of the protected resource. This node notices that the protected resource(link/node/set-of-links) is broken first and uses an FRR mechanism to protect that resource
Repair Node : The node to which the PLR wants to get the traffic to during the convergence period, once the protected resource fails, because the repair node is guanteed to have a path to the destination 'D'
Pre-Convergence State : A source 'S' is said to be in a pre-convergence state regarding a particular destination 'D' from the time the primary-path to 'D' fails until 'S' installs a new route to 'D'
Post-Convergence State : A source 'S' is said to be in a post-convergence state regarding a particular destination 'D' after it installs a new route to 'D'
P-space: The P-space of a router with respect to a protected link is the set of routers reachable from that specific router using the pre-convergence shortest paths without any of those paths (including equal-cost path splits) transiting that protected link.For example, the P-space of S with respect to link S-E is the set of routers that S can reach without using the protected link S-E
Extended P-space: Consider the set of neighbors of a router protecting a link. Exclude from that set of routers the router reachable over the protected link. The extended P-space of the protecting router with respect to the protected link is the union of the P-spaces of the neighbors in that set of neighbors with respect to the protected link
Q-space: The Q-space of a router with respect to a protected link is the set of routers from which that specific router can be reached without any path (including equal-cost path splits) transiting that protected link
PQ node: A PQ node of a node S with respect to a protected link S-E is a node that is a member of both the P-space (or the extended P-space) of S with respect to that protected link S-E and the Q-space of E with respect to that protected link S-E.
Difference betweem LFA/RLFA/TI-LFA
LFA :
The repair node is restricted to be the neighbor of the PLR
RLFA :
The repair node is not restricted to be the direct neighbor of the PLR. It can be a node from the PQ-space.
A repair tunnel would be created from the PLR to the repair node and this repair tunnel traverses the IGP shortest-path from the PLR to the repair node
The repair tunnel can be LDP-signalled(Targeted LDP session required from the PLR to the repair node )
TI-LFA:
SR-paths can be used as repair tunnels.Because the repair tunnel is an SR-path, it is not required to traverse the IGP shortest-path from the PLR to the repair node.It can be any viable path that can be specified by the PLR as an ordered list of segments.
Thus, the repair node can be outside of the PLR's P-space.
However, the repair node must be within the destination node's Q-space. Sometimes, the repair node is also the destination node.
No TLDP session required in case of TI-LFA as TI-LFA uses segment-routing thus eliminating the overhead of maintaining any state
Topology
 
TI-LFA FRR path using a PQ Node
Note: It should be ensured that prefix SIDs are unique globally.
Note: By default, the CSPF retry limit is 10 times and the CSPF retry interval is 10 seconds. If a policy does not come up within 100 seconds, it will require operator intervention.
TI-LFA FRR Path using a PQ node with OSPF-SR
PE1
 
PE1#configure terminal
Enter configure mode.
PE1(config)#interface lo
Enter interface mode.
PE1(config-if)#ip address 1.1.1.1/32 secondary
Configure the IP address of the interface.
PE1(config-if)#prefix-sid index 1
Configure prefix SID index value.
PE1(config-if)#exit
Exit interface mode.
PE1(config)#interface eth1
Enter interface mode.
PE1(config-if)#ip address 10.1.2.1/32
secondary
Configure the IP address of the interface.
PE1(config-if)#label-switching
Enable label switching.
PE1(config-if)#exit
Exit interface mode
PE1(config)#router ospf 100
Set the routing process ID .
PE1(config-router)#ospf router-id 1.1.1.1
Configuring OSPF router-id
PE1(config-router)#network 1.1.1.1/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
PE1(config-router)#network 10.1.2.0/24 area 0.0.0.0
secondary
Configure OSPF network in area 0
PE1(config-router)#segment-routing mpls
Enable segment routing under router OSPF process.
PE1(config-router)#exit
Exit router mode.
PE1(config)#exit
Exit configure mode
PE1(config)#commit
Commit the candidate configuration to the running configuration.
P1
 
P1#configure terminal
Enter configure mode.
P1(config)#interface lo
Enter interface mode.
P1(config-if)#ip address 1.1.1.2/32 secondary
Configure the IP address of the interface.
P1(config-if)#prefix-sid index 2
Configure prefix SID index value.
P1(config-if)#exit
Exit interface mode.
P1(config)#interface eth1
Enter interface mode.
P1(config-if)#ip address 10.1.2.2/32
secondary
Configure the IP address of the interface.
P1(config-if)#label-switching
Enable label switching.
P1(config-if)#exit
Exit interface mode.
P1(config)#interface eth2
Enter interface mode.
P1(config-if)#ip address 10.2.3.1/32
secondary
Configure the IP address of the interface.
P1(config-if)#label-switching
Enable label switching.
P1(config-if)#exit
Exit interface mode.
P1(config)#interface eth3
Enter interface mode.
P1(config-if)#ip address 10.2.6.1/32
secondary
Configure the IP address of the interface.
P1(config-if)#label-switching
Enable label switching.
P1(config-if)#exit
Exit interface mode.
P1(config)#router ospf 100
Set the routing process ID .
P1(config-router)#ospf router-id 1.1.1.2/32
secondary
Configure OSPF router-id
P1(config-router)#network 1.1.1.2/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P1(config-router)#network 10.1.2.0/24 area 0.0.0.0
secondary
Configure OSPF network in area 0
P1(config-router)#network 10.2.3.0/24 area 0.0.0.0
secondary
Configure OSPF network in area 0
P1(config-router)#network 10.2.6.0/24 area 0.0.0.0
secondary
Configure OSPF network in area 0
P1(config-router)#segment-routing mpls
Enable segment routing under router process.
P1(config-router)# fast-reroute per-prefix ti-lfa area 0.0.0.0
Enable per-prefix TI-LFA FRR computation for OSPF area 0
P1(config-router)#exit
Exit router mode.
P1(config)#exit
Exit configure mode
P1(config)#commit
Commit the candidate configuration to the running configuration.
P2
 
P2#configure terminal
Enter configure mode.
P2(config)#interface lo
Enter interface mode.
P2(config-if)#ip address 1.1.1.3/32 secondary
Configure the IP address of the interface.
P2(config-if)#prefix-sid index 3
Configure prefix SID index value.
P2(config-if)#exit
Exit interface mode.
P2(config)#interface eth1
Enter interface mode.
P2(config-if)#ip address 10.3.4.1/32
secondary
Configure the IP address of the interface.
P2(config-if)#label-switching
Enable label switching.
P2(config-if)#exit
Exit interface mode.
P2(config)#interface eth2
Enter interface mode.
P2(config-if)#ip address 10.2.3.2/32
secondary
Configure the IP address of the interface.
P2(config-if)#label-switching
Enable label switching.
P2(config-if)#exit
Exit interface mode.
P2(config)#interface eth3
Enter interface mode.
P2(config-if)#ip address 10.3.7.1/32
secondary
Configure the IP address of the interface.
P2(config-if)#label-switching
Enable label switching.
P2(config-if)#exit
Exit interface mode.
P2(config)#router ospf 100
Set the routing process ID .
P2(config-router)#ospf router-id 1.1.1.3/32
secondary
Configure OSPF router-id
P2(config-router)#network 1.1.1.3/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P2(config-router)#network 10.3.4.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P2(config-router)#network 10.2.3.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P2(config-router)#network 10.3.7.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P2(config-router)#segment-routing mpls
Enable segment routing under router process.
P2(config-router)#exit
Exit router mode.
P2(config)#exit
Exit configure mode
P2(config)#commit
Commit the candidate configuration to the running configuration.
P3
 
P3#configure terminal
Enter configure mode.
P3(config)#interface lo
Enter interface mode.
P3(config-if)#ip address 1.1.1.4/32 secondary
Configure the IP address of the interface.
P3(config-if)#prefix-sid index 4
Configure prefix SID index value.
P3(config-if)#exit
Exit interface mode.
P3(config)#interface eth1
Enter interface mode.
P3(config-if)#ip address 10.3.4.2/32
secondary
Configure the IP address of the interface.
P3(config-if)#label-switching
Enable label switching.
P3(config-if)#exit
Exit interface mode.
P3(config)#interface eth2
Enter interface mode.
P3(config-if)#ip address 10.4.5.1/32
secondary
Configure the IP address of the interface.
P3(config-if)#label-switching
Enable label switching.
P3(config-if)#exit
Exit interface mode.
P3(config)#router ospf 100
Set the routing process ID .
P3(config-router)#ospf router-id 1.1.1.4/32
secondary
Configure OSPF router-id
P3(config-router)#network 1.1.1.4/32 area 0.0.0.0
Configure OSPF network in area 0
P3(config-router)#network 10.3.4.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P3(config-router)#network 10.4.5.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P3(config-router)#segment-routing mpls
Enable segment routing under router process.
P3(config-router)#exit
Exit router mode.
P3(config)#exit
Exit configure mode
P3(config)#commit
Commit the candidate configuration to the running configuration.
P4
 
P4#configure terminal
Enter configure mode.
P4(config)#interface lo
Enter interface mode.
P4(config-if)#ip address 1.1.1.5/32 secondary
Configure the IP address of the interface.
P4(config-if)#prefix-sid index 5
Configure prefix SID index value.
P4(config-if)#exit
Exit interface mode.
P4(config)#interface eth1
Enter interface mode.
P4(config-if)#ip address 10.5.6.1/32
secondary
Configure the IP address of the interface.
P4(config-if)#label-switching
Enable label switching.
P4(config-if)#exit
Exit interface mode.
P4(config)#interface eth2
Enter interface mode.
P4(config-if)#ip address 10.4.5.2/32
secondary
Configure the IP address of the interface.
P4(config-if)#label-switching
Enable label switching.
P4(config-if)#exit
Exit interface mode.
P4(config)#router ospf 100
Set the routing process ID .
P4(config-router)#ospf router-id 1.1.1.5/32
secondary
Configure OSPF router-id
P4(config-router)#network 1.1.1.5/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P4(config-router)#network 10.4.5.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P4(config-router)#network 10.5.6.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P4(config-router)#segment-routing mpls
Enable segment routing under router process.
P4(config-router)#exit
Exit router mode.
P4(config)#exit
Exit configure mode
P4(config)#commit
Commit the candidate configuration to the running configuration.
P5
 
P5#configure terminal
Enter configure mode.
P5(config)#interface lo
Enter interface mode.
P5(config-if)#ip address 1.1.1.6/32 secondary
Configure the IP address of the interface.
P5(config-if)#prefix-sid index 6
Configure prefix SID index value.
P5(config-if)#exit
Exit interface mode.
P5(config)#interface eth1
Enter interface mode.
P5(config-if)#ip address 10.5.6.2/32
secondary
Configure the IP address of the interface.
P5(config-if)#label-switching
Enable label switching.
P5(config-if)#exit
Exit interface mode.
P5(config)#interface eth3
Enter interface mode.
P5(config-if)#ip address 10.2.6.2/32
secondary
Configure the IP address of the interface.
P5(config-if)#label-switching
Enable label switching.
P5(config-if)#exit
Exit interface mode.
P5(config)#router ospf 100
Set the routing process ID .
P5(config-router)#ospf router-id 1.1.1.6/32
secondary
Configure OSPF router-id
P5(config-router)#network 1.1.1.6/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P5(config-router)#network 10.2.6.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P5(config-router)#network 10.5.6.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
P5(config-router)#segment-routing mpls
Enable segment routing under router process.
P5(config-router)#exit
Exit router mode.
P5(config)#exit
Exit configure mode
P5(config)#commit
Commit the candidate configuration to the running configuration.
PE2
 
PE2#configure terminal
Enter configure mode.
PE2(config)#interface lo
Enter interface mode.
PE2(config-if)#ip address 1.1.1.7/32 secondary
Configure the IP address of the interface.
PE2(config-if)#prefix-sid index 7
Configure prefix SID index value.
PE2(config-if)#exit
Exit interface mode.
PE2(config)#interface eth3
Enter interface mode.
PE2(config-if)#ip address 10.3.7.2/32
secondary
Configure the IP address of the interface.
PE2(config-if)#label-switching
Enable label switching.
PE2(config-if)#exit
Exit interface mode.
PE2(config)#router ospf 100
Set the routing process ID .
PE2(config-router)#ospf router-id 1.1.1.7/32
secondary
Configuring OSPF router-id
PE2(config-router)#network 1.1.1.7/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
PE2(config-router)#network 10.3.7.0/32 area 0.0.0.0
secondary
Configure OSPF network in area 0
PE2(config-router)#segment-routing mpls
Enable segment routing under router OSPF process.
PE2(config-router)#exit
Exit router mode.
PE2(config)#exit
Exit configure mode
PE2(config)#commit
Commit the candidate configuration to the running configuration.
Validation 1
Verify OSPF adjacencies on P1
P1#show ip ospf neighbor
 
Total number of full neighbors: 3
OSPF process 100 VRF(default):
Neighbor ID Pri State Dead Time Address Interface Instance ID
1.1.1.1 1 Full/DR 00:00:37 10.1.2.1 eth1 0
1.1.1.3 1 Full/Backup 00:00:37 10.2.3.2 eth2 0
1.1.1.6 1 Full/Backup 00:00:32 10.2.6.2 eth3 0
Validation 2
Verify that the 2 PQ nodes in the topology are P4 (1.1.1.5) and P3 (1.1.1.4).
P4 is the PQ node for PE2 (1.1.1.7/32)
P1
P1#show ip ospf tilfa-backup-path
 
OSPF process 100:
Route [1.1.1.1]
NO PQ node
Route [1.1.1.2]
Route [1.1.1.3]
PQ-node: 1.1.1.5
Route [1.1.1.4]
PQ-node: 1.1.1.5
Route [1.1.1.5]
PQ-node: 1.1.1.4
Route [1.1.1.6]
PQ-node: 1.1.1.4
Route [1.1.1.7]
PQ-node: 1.1.1.5
Route [10.1.2.0]
Route [10.2.3.0]
Route [10.2.6.0]
Route [10.3.4.0]
Route [10.3.7.0]
Route [10.4.5.0]
Route [10.5.6.0]
Neighbor [1.1.1.1]
Neighbor [1.1.1.3]
PQ-node: 1.1.1.5
Neighbor [1.1.1.6]
PQ-node: 1.1.1.4
 
Displaying vertex-info in tilfa_network table
Vertex [1.1.1.1]
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 2
P node: 1.1.1.7 dist: 2
P node: 1.1.1.3 dist: 1
P node: 1.1.1.6 dist: 1
 
Vertex [1.1.1.2]
No P Nodes
No Q Nodes
 
Vertex [1.1.1.3]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 2
P node: 1.1.1.6 dist: 1
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 2
Q node: 1.1.1.7 dist: 2
PQ-node: 1.1.1.5
Backup out-interface: eth3
 
Vertex [1.1.1.4]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 2
P node: 1.1.1.6 dist: 1
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 2
Q node: 1.1.1.7 dist: 2
PQ-node: 1.1.1.5
Backup out-interface: eth3
 
Vertex [1.1.1.5]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 2
P node: 1.1.1.7 dist: 2
P node: 1.1.1.3 dist: 1
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 2
PQ-node: 1.1.1.4
Backup out-interface: eth2
 
Vertex [1.1.1.6]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 2
P node: 1.1.1.7 dist: 2
P node: 1.1.1.3 dist: 1
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 2
PQ-node: 1.1.1.4
Backup out-interface: eth2
 
Vertex [1.1.1.7]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 2
P node: 1.1.1.6 dist: 1
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 2
Q node: 1.1.1.7 dist: 2
PQ-node: 1.1.1.5
Backup out-interface: eth3
 
P1#
P1#show ip ospf tilfa-repair-list
 
1.1.1.1/32
Primary Path Metric :2
Primary Path Nexthop : 10.1.2.1, eth1
Route ftnix:1 ilmix:1
SR Incoming Label : 16001
SR outgoing Label : 3
NO PQ node
 
1.1.1.2/32
1.1.1.3/32
Primary Path Metric :2
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:2 ilmix:4
SR Incoming Label : 16003
SR outgoing Label : 3
PQ-node: 1.1.1.5
 
Backup ftnix:8 ilmix:9
Backup outgoing Label : 16003
Bypass_trunk id :101
Backup out interface: eth3
 
1.1.1.4/32
Primary Path Metric :3
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:3 ilmix:5
SR Incoming Label : 16004
SR outgoing Label : 16004
PQ-node: 1.1.1.5
 
Backup ftnix:9 ilmix:10
Backup outgoing Label : 16004
Bypass_trunk id :101
Backup out interface: eth3
 
Bypass-Trunk: 102 Name: 1.1.1.4_nexthop__10006 ftn_ix:7
ftn_info->trunk_ftn_ix : 7
Number Of outgoing label 1:
16004
Nexthop address: 10.2.3.2
 
1.1.1.5/32
Primary Path Metric :3
Primary Path Nexthop : 10.2.6.2, eth3
Route ftnix:4 ilmix:6
SR Incoming Label : 16005
SR outgoing Label : 16005
PQ-node: 1.1.1.4
 
Backup ftnix:10 ilmix:11
Backup outgoing Label : 16005
Bypass_trunk id :102
Backup out interface: eth2
 
Bypass-Trunk: 101 Name: 1.1.1.5_nexthop__10007 ftn_ix:6
ftn_info->trunk_ftn_ix : 6
Number Of outgoing label 1:
16005
Nexthop address: 10.2.6.2
 
1.1.1.6/32
Primary Path Metric :2
Primary Path Nexthop : 10.2.6.2, eth3
Route ftnix:5 ilmix:8
SR Incoming Label : 16006
SR outgoing Label : 3
PQ-node: 1.1.1.4
 
Backup ftnix:11 ilmix:12
Backup outgoing Label : 16006
Bypass_trunk id :102
Backup out interface: eth2
 
1.1.1.7/32
Primary Path Metric :3
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:12 ilmix:15
SR Incoming Label : 16007
SR outgoing Label : 16007
PQ-node: 1.1.1.5
 
Backup ftnix:14 ilmix:16
Backup outgoing Label : 16007
Bypass_trunk id :101
Backup out interface: eth3
 
10.1.2.0/24
10.2.3.0/24
10.2.6.0/24
10.3.4.0/24
10.3.7.0/24
10.4.5.0/24
10.5.6.0/24
P1#
 
P1#show mpls ilm-table
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
 
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
O> 1.1.1.4/32 5 16004 16004 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.4/32 18 16004 16004 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.3/32 3 16003 3 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.3/32 17 16003 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.1/32 1 16001 3 N/A eth1 10.1.2.1 LSP_DEFAULT
O> 10.1.2.1/32 2 24320 3 N/A eth1 10.1.2.1 LSP_DEFAULT
O> 1.1.1.6/32 7 16006 3 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.6/32 20 16006 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.5/32 6 16005 16005 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.5/32 19 16005 16005 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.7/32 15 16007 16007 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.7/32 21 16007 16007 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.3.2/32 4 24321 3 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 10.2.3.2/32 22 24321 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.6.2/32 8 24322 3 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.6.2/32 23 24322 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
 
P1#show mpls forwarding-table
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN
 
Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
O> 1.1.1.1/32 1 2 0 Yes LSP_DEFAULT 3 eth1 No 10.1.2.1
O> 1.1.1.3/32 2 4 0 Yes LSP_DEFAULT 3 eth2 No 10.2.3.2
O> 1.1.1.3/32 8 14 0 No LSP_DEFAULT 16003 - No 10.2.6.2
O> 1.1.1.4/32 3 6 0 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
O> 1.1.1.4/32 9 16 0 No LSP_DEFAULT 16004 - No 10.2.6.2
O> 1.1.1.4/32 7 12 102 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
O> 1.1.1.5/32 4 8 0 Yes LSP_DEFAULT 16005 eth3 No 10.2.6.2
O> 1.1.1.5/32 10 18 0 No LSP_DEFAULT 16005 - No 10.2.3.2
O> 1.1.1.5/32 6 7 101 Yes LSP_DEFAULT 16005 eth3 No 10.2.6.2
O> 1.1.1.6/32 5 10 0 Yes LSP_DEFAULT 3 eth3 No 10.2.6.2
O> 1.1.1.6/32 11 20 0 No LSP_DEFAULT 16006 - No 10.2.3.2
O> 1.1.1.7/32 12 22 0 Yes LSP_DEFAULT 16007 eth2 No 10.2.3.2
O> 1.1.1.7/32 14 24 0 No LSP_DEFAULT 16007 - No 10.2.6.2
K> 202.1.1.0/24 13 - - - LSP_DEFAULT - eth2 No 1.1.1.7
P1#
TI-LFA FRR Path using a PQ node with ISIS-SR
PE1
 
PE1#configure terminal
Enter configure mode.
PE1(config)#interface lo
Enter interface mode.
PE1(config-if)#ip address 1.1.1.1/32 secondary
Configure the IP address of the interface.
PE1(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
PE1(config-if)#prefix-sid index 1
Configure prefix SID index value.
PE1(config-if)#exit
Exit interface mode.
PE1(config)#interface eth1
Enter interface mode.
PE1(config-if)#ip address 10.1.2.1/32
secondary
Configure the IP address of the interface.
PE1(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
PE1(config-if)#label-switching
Enable label switching.
PE1(config)#router isis 1
Set the routing process ID.
PE1(config-router)#metric-style wide
Configure metric style as wide.
PE1(config-router)#net 49.0000.0000.0000.0001.00
Configure network entity title (NET).
PE1(config-router)#mpls traffic-eng router-id 1.1.1.1
Enable MPLS Traffic Engineering under router process.
PE1(config-router)#mpls traffic-eng level-1
Enable MPLS Traffic Engineering as level-1
PE1(config-router)#mpls traffic-eng level-2
Enable MPLS Traffic Engineering as level-2
PE1(config-router)#segment-routing mpls
Enable segment routing under router ISIS process.
PE1(config-router)#exit
Exit router mode.
PE1(config)#exit
Exit configure mode
P1
 
P1#configure terminal
Enter configure mode.
P1(config)#interface lo
Enter interface mode.
P1(config-if)#ip address 1.1.1.2/32 secondary
Configure the IP address of the interface.
P1(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P1(config-if)#prefix-sid index 2
Configure prefix SID index value.
P1(config-if)#exit
Exit interface mode.
P1(config)#interface eth1
Enter interface mode.
P1(config-if)#ip address 10.1.2.2/32
secondary
Configure the IP address of the interface.
P1(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P1(config-if)#label-switching
Enable label switching.
P1(config-if)#exit
Exit interface mode.
P1(config)#interface eth2
Enter interface mode.
P1(config-if)#ip address 10.2.3.1/32
secondary
Configure the IP address of the interface.
P1(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P1(config-if)#label-switching
Enable label switching.
P1(config-if)#exit
Exit interface mode.
P1(config)#interface eth3
Enter interface mode.
P1(config-if)#ip address 10.2.6.1/32
secondary
Configure the IP address of the interface.
P1(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P1(config-if)#label-switching
Enable label switching.
P1(config-if)#exit
Exit interface mode.
P1(config)#router isis 1
Set the routing process ID .
P1(config-router)#metric-style wide
Configure metric style as wide.
P1(config-router)#net 49.0000.0000.0000.0002.00
Configure Network entity title (NET).
P1(config-router)#mpls traffic-eng router-id 1.1.1.2
Enable MPLS Traffic Engineering under router process.
P1(config-router)#mpls traffic-eng level-1
Enable MPLS Traffic Engineering as level-1.
P1(config-router)#mpls traffic-eng level-2
Enable MPLS Traffic Engineering as level-2.
P1(config-router)#capability cspf
Enable cspf capability under ISIS 1 process.
P1(config-router)#segment-routing mpls
Enable segment routing under router process.
P1(config-router)# fast-reroute ti-lfa level-1 proto ipv4
Enable per-prefix TI-LFA FRR computation for ISIS level-1
P1(config-router)#exit
Exit router mode.
P1(config)#exit
Exit configure mode
P2
 
P2#configure terminal
Enter configure mode.
P2(config)#interface lo
Enter interface mode.
P2(config-if)#ip address 1.1.1.3/32
secondary
Configure the IP address of the interface.
P2(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P2(config-if)#prefix-sid index 3
Configure prefix SID index value.
P2(config-if)#exit
Exit interface mode.
P2(config)#interface eth1
Enter interface mode.
P2(config-if)#ip address 10.3.4.1/32
secondary
Configure the IP address of the interface.
P2(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P2(config-if)#label-switching
Enable label switching.
P2(config-if)#exit
Exit interface mode.
P2(config)#interface eth2
Enter interface mode.
P2(config-if)#ip address 10.2.3.2/32
secondary
Configure the IP address of the interface.
P2(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P2(config-if)#label-switching
Enable label switching.
P2(config-if)#exit
Exit interface mode.
P2(config)#interface eth3
Enter interface mode.
P2(config-if)#ip address 10.3.7.1/32
secondary
Configure the IP address of the interface.
P2(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P2(config-if)#label-switching
Enable label switching.
P2(config-if)#exit
Exit interface mode.
P2(config)#router isis 1
Set the routing process ID .
P2(config-router)#metric-style wide
Configure metric style as wide.
P2(config-router)#net 49.0000.0000.0000.0003.00
Configure Network entity title (NET).
P2(config-router)#mpls traffic-eng router-id 1.1.1.3
Enable MPLS Traffic Engineering under router process.
P2(config-router)#mpls traffic-eng level-1
Enable MPLS Traffic Engineering as level-1.
P2(config-router)#mpls traffic-eng level-2
Enable MPLS Traffic Engineering as level-2
P2(config)#router isis 1
Set the routing process ID .
P2(config-router)#metric-style wide
Configure metric style as wide.
P2(config-router)#net 49.0001.0000.0000.0003.00
Configure Network entity title (NET).
P2(config-router)#segment-routing mpls
Enable segment routing under router process.
P2(config-router)#exit
Exit router mode.
P3
 
P3#configure terminal
Enter configure mode.
P3(config)#interface lo
Enter interface mode.
P3(config-if)#ip address 1.1.1.4/32
secondary
Configure the IP address of the interface.
P3(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P3(config-if)#prefix-sid index 4
Configure prefix SID index value.
P3(config-if)#exit
Exit interface mode.
P3(config)#interface eth1
Enter interface mode.
P3(config-if)#ip address 10.3.4.2/32
secondary
Configure the IP address of the interface.
P3(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P3(config-if)#label-switching
Enable label switching.
P3(config-if)#exit
Exit interface mode.
P3(config)#interface eth2
Enter interface mode.
P3(config-if)ip address 10.4.5.1/32
secondary
Configure the IP address of the interface.
P3(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P3(config-if)#label-switching
Enable label switching.
P3(config-if)#exit
Exit interface mode.
P3(config)#router isis 1
Set the routing process ID .
P3(config-router)#metric-style wide
Configure metric style as wide.
P3(config-router)#net 49.0000.0000.0000.0004.00
Configure Network entity title (NET).
P3(config-router)#mpls traffic-eng router-id 1.1.1.4
Enable MPLS Traffic Engineering under router process.
P3(config-router)#mpls traffic-eng level-1
Enable MPLS Traffic Engineering as level-1.
P3(config-router)#mpls traffic-eng level-2
Enable MPLS Traffic Engineering as level-2.
P3(config-router)#exit
Exit router isis mode
P3(config)#router isis 1
Set the routing process ID .
P3(config-router)#metric-style wide
Configure metric style as wide.
P3(config-router)#net 49.0000.0000.0000.0004.00
Configure Network entity title (NET).
P3(config-router)#segment-routing mpls
Enable segment routing under router process.
P3(config-router)#exit
Exit router mode.
P4
 
P4#configure terminal
Enter configure mode.
P4(config)#interface lo
Enter interface mode.
P4(config-if)#ip address 1.1.1.5/32
Configure the IP address of the interface.
P4(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P4(config-if)#prefix-sid index 5
Configure prefix SID index value.
P4(config-if)#exit
Exit interface mode.
P4(config)#interface eth1
Enter interface mode.
P4(config-if)#ip address 10.5.6.1/32
secondary
Configure the IP address of the interface.
P4(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P4(config-if)#label-switching
Enable label switching.
P4(config-if)#exit
Exit interface mode.
P4(config)#interface eth2
Enter interface mode.
P4(config-if)#ip address 10.4.5.2/32
secondary
Configure the IP address of the interface.
P4(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P4(config-if)#label-switching
Enable label switching.
P4(config-if)#exit
Exit interface mode.
P4(config)#router isis 1
Set the routing process ID .
P4(config-router)#metric-style wide
Configure metric style as wide.
P4(config-router)#net 49.0000.0000.0000.0005.00
Configure Network entity title (NET).
P4(config-router)#mpls traffic-eng router-id 1.1.1.5
Enable MPLS Traffic Engineering under router process.
P4(config-router)#mpls traffic-eng level-1
Enable MPLS Traffic Engineering as level-1.
P4(config-router)#mpls traffic-eng level-2
Enable MPLS Traffic Engineering as level-2.
P4(config-router)#segment-routing mpls
Enable segment routing under router process.
P4(config-router)#exit
Exit router mode.
P5
 
P5#configure terminal
Enter configure mode.
P5(config)#interface lo
Enter interface mode.
P5(config-if)#ip address 1.1.1.6/32
secondary
Configure the IP address of the interface.
P5(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P5(config-if)#prefix-sid index 6
Configure prefix SID index value.
P5(config-if)#exit
Exit interface mode.
P5(config)#interface eth1
Enter interface mode.
P5(config-if)#ip address 10.5.6.2/32
secondary
Configure the IP address of the interface.
P5(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P5(config-if)#label-switching
Enable label switching.
P5(config-if)#exit
Exit interface mode.
P5(config)#interface eth3
Enter interface mode.
P5(config-if)#ip address 10.2.6.2/32
secondary
Configure the IP address of the interface.
P5(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
P5(config-if)#label-switching
Enable label switching.
P5(config-if)#exit
Exit interface mode.
P5(config)#router isis 1
Set the routing process ID .
P5(config-router)#metric-style wide
Configure metric style as wide.
P5(config-router)#net 49.0000.0000.0000.0006.00
Configure Network entity title (NET).
P5(config-router)#mpls traffic-eng router-id 1.1.1.6
Enable MPLS Traffic Engineering under router process.
P5(config-router)#mpls traffic-eng level-1
Enable MPLS Traffic Engineering as level-1.
P5(config-router)#mpls traffic-eng level-2
Enable MPLS Traffic Engineering as level-2.
P5(config-router)#segment-routing mpls
Enable segment routing under router process.
P5(config-router)#exit
Exit router mode.
P5(config)#commit
Commit the candidate configuration to the running configuration.
PE2
 
PE2#configure terminal
Enter configure mode.
PE2(config)#interface lo
Enter interface mode.
PE2(config-if)#ip address 1.1.1.7/32
secondary
Configure the IP address of the interface.
PE2(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
PE2(config-if)#prefix-sid index 7
Configure prefix SID index value.
PE2(config-if)#exit
Exit interface mode.
PE2(config)#interface eth3
Enter interface mode.
PE2(config-if)#ip address 10.3.7.2/32
secondary
Configure the IP address of the interface.
PE2(config-if)#ip router isis 1
Make the interface part of the router ISIS 1 instance.
PE2(config-if)#label-switching
Enable label switching.
PE2(config-if)#exit
Exit interface mode.
PE2(config)#router isis 1
Set the routing process ID .
PE2(config-router)#metric-style wide
Configure metric style as wide.
PE2(config-router)#net 49.0000.0000.0000.0007.00
Configure Network entity title (NET).
PE2(config-router)#mpls traffic-eng router-id 1.1.1.7
Enable MPLS Traffic Engineering under router process.
PE2(config-router)#mpls traffic-eng level-1
Enable MPLS Traffic Engineering as level-1.
PE2(config-router)#mpls traffic-eng level-2
Enable MPLS Traffic Engineering as level-2.
PE2(config-router)#segment-routing mpls
Enable segment routing under router process.
PE2(config-router)#exit
Exit router mode.
PE2(config)#commit
Commit the candidate configuration to the running configuration.
Validation 1
P1
P1#show clns neighbors
 
Total number of L1 adjacencies: 3
Total number of L2 adjacencies: 3
Total number of adjacencies: 6
Tag 1: VRF : default
System Id Interface SNPA State Holdtime Type Protocol
0000.0000.0003 eth2 3c2c.99c9.097f Up 7 L1 IS-IS
Up 7 L2 IS-IS
0000.0000.0006 eth3 3c2c.992c.ec83 Up 6 L1 IS-IS
Up 6 L2 IS-IS
0000.0000.0001 eth1 04f8.f824.d009 Up 19 L1 IS-IS
Up 19 L2 IS-IS
Validation 2
P1
P1#show isis tilfa pq
 
IS-IS Level-1 Link State Database:
 
Node: 0000.0000.0001.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0003.00-00 primary dist:10
P node: 0000.0000.0006.00-00 primary dist:10
No PQ Node found on backup path
 
Node: 0000.0000.0003.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:20
Q node: 0000.0000.0007.00-00 primary dist:20
PQ Node: 0000.0000.0005.00-00 backup dist:20
 
Node: 0000.0000.0004.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:20
Q node: 0000.0000.0007.00-00 primary dist:20
PQ Node: 0000.0000.0005.00-00 backup dist:20
 
Node: 0000.0000.0005.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0003.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:20
PQ Node: 0000.0000.0004.00-00 backup dist:20
 
Node: 0000.0000.0006.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0003.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:20
PQ Node: 0000.0000.0004.00-00 backup dist:20
 
Node: 0000.0000.0007.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:20
Q node: 0000.0000.0007.00-00 primary dist:20
PQ Node: 0000.0000.0005.00-00 backup dist:20
 
P1#show ip isis route tilfa
 
Tag : 1 VRF : default
Codes : L1 - IS-IS level-1, L2 - IS-IS level-2,
C - Connected Routes, ia - IS-IS inter area
 
1.1.1.1/32
L1: Primary Path Nexthop : 10.1.2.1, eth1
Route ftnix :1 ilmix :5
SR Incoming Label : 16001
SR outgoing Label : 3
NO PQ node
NO Backup
 
 
1.1.1.2/32
C: Primary Path Nexthop : 0.0.0.0, lo
Route ftnix :0 ilmix :1
SR Incoming Label : 16002
No SR outgoing Label
NO PQ node
NO Backup
 
 
1.1.1.3/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :2 ilmix :6
SR Incoming Label : 16003
SR outgoing Label : 3
PQ node : 1.1.1.5
Backup ftnix :10 ilmix :47
Backup outgoing Label : 16003
Bypass_trunk id :2201
Backup out interface : eth3
 
 
1.1.1.4/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :3 ilmix :7
SR Incoming Label : 16004
SR outgoing Label : 16004
PQ node : 1.1.1.5
Backup ftnix :11 ilmix :48
Backup outgoing Label : 16004
Bypass_trunk id :2201
Backup out interface : eth3
 
Trunk : 2202 :1.1.1.4_nh_10006 ftn_ix : 9 ref_cnt:3
Number Of outgoing label : 1
16004
Nexthop address : 10.2.3.2
 
 
1.1.1.5/32
L1: Primary Path Nexthop : 10.2.6.2, eth3
Route ftnix :4 ilmix :8
SR Incoming Label : 16005
SR outgoing Label : 16005
PQ node : 1.1.1.4
Backup ftnix :12 ilmix :49
Backup outgoing Label : 16005
Bypass_trunk id :2202
Backup out interface : eth2
 
Trunk : 2201 :1.1.1.5_nh_10007 ftn_ix : 8 ref_cnt:4
Number Of outgoing label : 1
16005
Nexthop address : 10.2.6.2
 
 
1.1.1.6/32
L1: Primary Path Nexthop : 10.2.6.2, eth3
Route ftnix :5 ilmix :15
SR Incoming Label : 16006
SR outgoing Label : 3
PQ node : 1.1.1.4
Backup ftnix :13 ilmix :50
Backup outgoing Label : 16006
Bypass_trunk id :2202
Backup out interface : eth2
 
 
1.1.1.7/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :6 ilmix :40
SR Incoming Label : 16007
SR outgoing Label : 16007
PQ node : 1.1.1.5
Backup ftnix :14 ilmix :53
Backup outgoing Label : 16007
Bypass_trunk id :2201
Backup out interface : eth3
 
P1#
 
P1#show mpls ilm-table
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
 
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
i> 10.1.2.1/32 2 24960 3 N/A eth1 10.1.2.1 LSP_DEFAULT
i> 1.1.1.4/32 7 16004 16004 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.4/32 48 16004 16004 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.2/32 1 16002 Nolabel N/A N/A 127.0.0.1 LSP_DEFAULT
i> 1.1.1.1/32 5 16001 3 N/A eth1 10.1.2.1 LSP_DEFAULT
i> 1.1.1.3/32 6 16003 3 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.3/32 47 16003 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.6/32 15 16006 3 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.6/32 50 16006 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.5/32 8 16005 16005 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.5/32 49 16005 16005 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.7/32 40 16007 16007 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.7/32 53 16007 16007 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.3.2/32 3 24961 3 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 10.2.3.2/32 51 24961 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.6.2/32 4 24962 3 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.6.2/32 52 24962 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
P1#
 
P1#show mpls forwarding-table
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN
 
Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
i> 1.1.1.1/32 1 5 0 Yes LSP_DEFAULT 3 eth1 No 10.1.2.1
i> 1.1.1.3/32 2 3 0 Yes LSP_DEFAULT 3 eth2 No 10.2.3.2
i> 1.1.1.3/32 10 15 0 No LSP_DEFAULT 16003 - No 10.2.6.2
i> 1.1.1.4/32 3 7 0 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
i> 1.1.1.4/32 11 20 0 No LSP_DEFAULT 16004 - No 10.2.6.2
i> 1.1.1.4/32 9 13 2202 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
i> 1.1.1.5/32 4 8 0 Yes LSP_DEFAULT 16005 eth3 No 10.2.6.2
i> 1.1.1.5/32 12 21 0 No LSP_DEFAULT 16005 - No 10.2.3.2
i> 1.1.1.5/32 8 12 2201 Yes LSP_DEFAULT 16005 eth3 No 10.2.6.2
i> 1.1.1.6/32 5 10 0 Yes LSP_DEFAULT 3 eth3 No 10.2.6.2
i> 1.1.1.6/32 13 22 0 No LSP_DEFAULT 16006 - No 10.2.3.2
i> 1.1.1.7/32 6 11 0 Yes LSP_DEFAULT 16007 eth2 No 10.2.3.2
i> 1.1.1.7/32 14 24 0 No LSP_DEFAULT 16007 - No 10.2.6.2
K> 202.1.1.0/24 7 - - - LSP_DEFAULT - eth2 No 1.1.1.7
P1#
 
P1#show mpls ftn-table 1.1.1.4/32
Primary FTN entry with FEC: 1.1.1.4/32, id: 3, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 3, in intf: - in label: 0 out-segment ix: 6
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 6, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16004
Nexthop addr: 10.2.3.2 cross connect ix: 3, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.4/32, id: 11, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 10, in intf: - in label: 0 out-segment ix: 18
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 18, owner: ISIS-SR, Stale: NO, ISIS-SR out intf: eth3, transport out intf: N/A, out label: 16004
Nexthop addr: 10.2.6.2 cross connect ix: 10, op code: Push and Lookup
 
bypass_ftn_ix 8
 
Primary FTN entry with FEC: 1.1.1.4/32, id: 9, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 2202, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 3, in intf: - in label: 0 out-segment ix: 6
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 6, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16004
Nexthop addr: 10.2.3.2 cross connect ix: 3, op code: Push
P1#
 
P1#show mpls ftn-table 1.1.1.5/32
Primary FTN entry with FEC: 1.1.1.5/32, id: 4, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 7, in intf: - in label: 0 out-segment ix: 16
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 16, owner: OSPF-SR, Stale: NO, out intf: eth3, out label: 16005
Nexthop addr: 10.2.6.2 cross connect ix: 7, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.5/32, id: 12, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 8, in intf: - in label: 0 out-segment ix: 17
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 17, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth2, transport out intf: N/A, out label: 16005
Nexthop addr: 10.2.3.2 cross connect ix: 8, op code: Push and Lookup
 
bypass_ftn_ix 9
 
Primary FTN entry with FEC: 1.1.1.5/32, id: 8, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 2201, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 7, in intf: - in label: 0 out-segment ix: 16
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 16, owner: OSPF-SR, Stale: NO, out intf: eth3, out label: 16005
Nexthop addr: 10.2.6.2 cross connect ix: 7, op code: Push
 
 
P1#
 
P1#show mpls ftn-table 1.1.1.7/32
Primary FTN entry with FEC: 1.1.1.7/32, id: 6, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 4, in intf: - in label: 0 out-segment ix: 4
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 4, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16007
Nexthop addr: 10.2.3.2 cross connect ix: 4, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.7/32, id: 14, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 11, in intf: - in label: 0 out-segment ix: 23
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 23, owner: ISIS-SR, Stale: NO, ISIS-SR out intf: eth3, transport out intf: N/A, out label: 16007
Nexthop addr: 10.2.6.2 cross connect ix: 11, op code: Push and Lookup
 
bypass_ftn_ix 8
 
P1#
 
 
Topology
 
TI-LFA FRR path using a PQ Node that is a Direct Neighbor
TI-LFA FRR Path using a Direct Neighbor with OSPF-SR
P1
 
P1#configure terminal
Enter configure mode.
P1(config)#interface eth3
Enter interface mode.
P1(config-if)#ip ospf cost 1000
Configure the OSPF cost for the interface
P1(config-if)#exit
Exit interface mode.
P1(config)#exit
Exit configure mode
P5
 
P5#configure terminal
Enter configure mode.
P5(config)#interface eth3
Enter interface mode.
P5(config-if)#ip ospf cost 1000
Configure the OSPF cost for the interface
P5(config-if)#exit
Exit interface mode.
P5(config)#exit
Exit configure mode
Validation
P1
P1#show ip ospf tilfa-backup-path
OSPF process 100:
Route [1.1.1.1]
NO PQ node
Route [1.1.1.2]
NO PQ node
Route [1.1.1.3]
PQ-node: 1.1.1.6
Route [1.1.1.4]
PQ-node: 1.1.1.6
Route [1.1.1.5]
PQ-node: 1.1.1.6
Route [1.1.1.6]
PQ-node: 1.1.1.6
Route [1.1.1.7]
PQ-node: 1.1.1.6
Route [10.1.2.0]
Route [10.2.3.0]
Route [10.2.6.0]
Route [10.3.4.0]
Route [10.3.7.0]
Route [10.4.5.0]
Route [10.5.6.0]
Neighbor [1.1.1.1]
Neighbor [1.1.1.3]
PQ-node: 1.1.1.6
Neighbor [1.1.1.6]
PQ-node: 1.1.1.3
 
Displaying vertex-info in tilfa_network table
Vertex [1.1.1.1]
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 3
P node: 1.1.1.6 dist: 4
P node: 1.1.1.7 dist: 2
P node: 1.1.1.3 dist: 1
P node: 1.1.1.6 dist: 4
 
Vertex [1.1.1.2]
No P Nodes
No Q Nodes
 
Vertex [1.1.1.3]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.3 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 3
P node: 1.1.1.7 dist: 2
P node: 1.1.1.6 dist: 4
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 3
Q node: 1.1.1.6 dist: 4
Q node: 1.1.1.7 dist: 2
PQ-node: 1.1.1.6
Backup out-interface: eth3
 
Vertex [1.1.1.4]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.3 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 3
P node: 1.1.1.7 dist: 2
P node: 1.1.1.6 dist: 4
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 3
Q node: 1.1.1.6 dist: 4
Q node: 1.1.1.7 dist: 2
PQ-node: 1.1.1.6
Backup out-interface: eth3
 
Vertex [1.1.1.5]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.3 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 3
P node: 1.1.1.7 dist: 2
P node: 1.1.1.6 dist: 4
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 3
Q node: 1.1.1.6 dist: 4
Q node: 1.1.1.7 dist: 2
PQ-node: 1.1.1.6
Backup out-interface: eth3
 
Vertex [1.1.1.6]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.3 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 3
P node: 1.1.1.7 dist: 2
P node: 1.1.1.6 dist: 4
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 3
Q node: 1.1.1.6 dist: 4
Q node: 1.1.1.7 dist: 2
PQ-node: 1.1.1.6
Backup out-interface: eth3
 
Vertex [1.1.1.7]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.3 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.5 dist: 3
P node: 1.1.1.7 dist: 2
P node: 1.1.1.6 dist: 4
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.5 dist: 3
Q node: 1.1.1.6 dist: 4
Q node: 1.1.1.7 dist: 2
PQ-node: 1.1.1.6
Backup out-interface: eth3
 
P1#show ip ospf tilfa-repair-list
 
1.1.1.1/32
Primary Path Metric :2
Primary Path Nexthop : 10.1.2.1, eth1
Route ftnix:1 ilmix:1
SR Incoming Label : 16001
SR outgoing Label : 3
NO PQ node
 
1.1.1.2/32
Primary Path Metric :1
Primary Path Nexthop : 1.1.1.2, lo
Route ftnix:0 ilmix:0
NO PQ node
 
1.1.1.3/32
Primary Path Metric :2
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:2 ilmix:3
SR Incoming Label : 16003
SR outgoing Label : 3
PQ-node: 1.1.1.6
 
Backup ftnix:9 ilmix:24
Backup outgoing Label : 16003
Bypass_trunk id :103
Backup out interface: eth3
 
1.1.1.4/32
Primary Path Metric :3
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:5 ilmix:8
SR Incoming Label : 16004
SR outgoing Label : 16004
PQ-node: 1.1.1.6
 
Backup ftnix:10 ilmix:38
Backup outgoing Label : 16004
Bypass_trunk id :103
Backup out interface: eth3
 
1.1.1.5/32
Primary Path Metric :4
Primary Path Nexthop : 10.2.3.2, eth3
Route ftnix:6 ilmix:15
SR Incoming Label : 16005
SR outgoing Label : 16005
PQ-node: 1.1.1.6
 
Backup ftnix:11 ilmix:39
Backup outgoing Label : 16005
Bypass_trunk id :103
Backup out interface: eth2
 
1.1.1.6/32
Primary Path Metric :5
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:3 ilmix:4
SR Incoming Label : 16006
SR outgoing Label : 16006
PQ-node: 1.1.1.6
 
Backup ftnix:12 ilmix:40
Backup outgoing Label : 3
Bypass_trunk id :103
Backup out interface: eth3
 
Bypass-Trunk: 103 Name: 1.1.1.6_nexthop__10007 ftn_ix:14
ftn_info->trunk_ftn_ix : 14
Number Of outgoing label 1:
3
Nexthop address: 10.2.6.2
 
1.1.1.7/32
Primary Path Metric :3
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:4 ilmix:7
SR Incoming Label : 16007
SR outgoing Label : 16007
PQ-node: 1.1.1.6
 
Backup ftnix:13 ilmix:41
Backup outgoing Label : 16007
Bypass_trunk id :103
Backup out interface: eth3
 
10.1.2.0/24
10.2.3.0/24
10.2.6.0/24
10.3.4.0/24
10.3.7.0/24
10.4.5.0/24
10.5.6.0/24
P1#
 
P1#show mpls ilm-table
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
 
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
O> 1.1.1.6/32 8 16006 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.6/32 23 16006 3 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.4/32 5 16004 16004 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.4/32 21 16004 16004 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.3/32 4 16003 3 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.3/32 20 16003 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.1/32 1 16001 3 N/A eth1 10.1.2.1 LSP_DEFAULT
O> 1.1.1.5/32 6 16005 16005 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.5/32 22 16005 16005 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.1.2.1/32 2 24320 3 N/A eth1 10.1.2.1 LSP_DEFAULT
O> 1.1.1.7/32 15 16007 16007 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.7/32 24 16007 16007 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.3.2/32 3 24321 3 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 10.2.3.2/32 17 24321 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.6.2/32 7 24322 3 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.6.2/32 25 24322 3 N/A eth2 10.2.3.2 LSP_DEFAULT
P1#
P1#show mpls forwarding-table
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN
 
Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
O> 1.1.1.1/32 1 2 0 Yes LSP_DEFAULT 3 eth1 No 10.1.2.1
O> 1.1.1.3/32 2 4 0 Yes LSP_DEFAULT 3 eth2 No 10.2.3.2
O> 1.1.1.3/32 8 11 0 No LSP_DEFAULT 16003 - No 10.2.6.2
O> 1.1.1.3/32 6 7 101 Yes LSP_DEFAULT 3 eth2 No 10.2.3.2
O> 1.1.1.4/32 3 6 0 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
O> 1.1.1.4/32 9 15 0 No LSP_DEFAULT 16004 - No 10.2.6.2
O> 1.1.1.5/32 4 8 0 Yes LSP_DEFAULT 16005 eth2 No 10.2.3.2
O> 1.1.1.5/32 10 18 0 No LSP_DEFAULT 16005 - No 10.2.6.2
O> 1.1.1.6/32 5 10 0 Yes LSP_DEFAULT 16006 eth2 No 10.2.3.2
O> 1.1.1.6/32 11 20 0 No LSP_DEFAULT 3 eth3 No 10.2.6.2
O> 1.1.1.6/32 15 25 103 Yes LSP_DEFAULT 3 eth3 No 10.2.6.2
O> 1.1.1.7/32 12 22 0 Yes LSP_DEFAULT 16007 eth2 No 10.2.3.2
O> 1.1.1.7/32 14 24 0 No LSP_DEFAULT 16007 - No 10.2.6.2
K> 202.1.1.0/24 13 - - - LSP_DEFAULT - eth2 No 1.1.1.7
P1#
 
P1#show mpls ftn-table 1.1.1.6/32
Primary FTN entry with FEC: 1.1.1.6/32, id: 5, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 9, in intf: - in label: 0 out-segment ix: 19
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 19, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth2, transport out intf: N/A, out label: 16006
Nexthop addr: 10.2.3.2 cross connect ix: 9, op code: Push and Lookup
 
 
Non-primary FTN entry with FEC: 1.1.1.6/32, id: 11, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 5, in intf: - in label: 0 out-segment ix: 9
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 9, owner: N/A, Stale: NO, out intf: eth3, out label: 3
Nexthop addr: 10.2.6.2 cross connect ix: 5, op code: Push
 
bypass_ftn_ix 15
 
Primary FTN entry with FEC: 1.1.1.6/32, id: 15, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 103, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 5, in intf: - in label: 0 out-segment ix: 9
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 9, owner: N/A, Stale: NO, out intf: eth3, out label: 3
Nexthop addr: 10.2.6.2 cross connect ix: 5, op code: Push
 
 
P1#
 
 
P1#show mpls ftn-table 1.1.1.7/32
Primary FTN entry with FEC: 1.1.1.7/32, id: 12, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 10, in intf: - in label: 0 out-segment ix: 21
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 21, owner: OSPF-SR, Stale: NO, out intf: eth2, out label: 16007
Nexthop addr: 10.2.3.2 cross connect ix: 10, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.7/32, id: 14, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 11, in intf: - in label: 0 out-segment ix: 23
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 23, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth3, transport out intf: N/A, out label: 16007
Nexthop addr: 10.2.6.2 cross connect ix: 11, op code: Push and Lookup
 
bypass_ftn_ix 15
 
P1#
TI-LFA FRR Path using a Direct Neighbor with ISIS-SR
P1
 
P1#configure terminal
Enter configure mode.
P1(config)#interface eth3
Enter interface mode.
P1(config-if)#isis wide-metric 1000
Configure the ISIS wide-metric for interface
P1(config-if)#exit
Exit interface mode.
P1(config)#exit
Exit configure mode
P1(config)#commit
Commit the candidate configuration to the running configuration.
P5
 
P5#configure terminal
Enter configure mode.
P5(config)#interface eth3
Enter interface mode.
P5(config-if)#isis wide-metric 1000
Configure the ISIS wide-metric for interface
P5(config-if)#exit
Exit interface mode.
P5(config)#exit
Exit configure mode
P5(config)#commit
Commit the candidate configuration to the running configuration.
Validation
P1
P1#show isis tilfa pq
IS-IS Level-1 Link State Database:
Node: 0000.0000.0001.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:30
P node: 0000.0000.0006.00-00 primary dist:40
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0003.00-00 primary dist:10
P node: 0000.0000.0006.00-00 primary dist:40
No PQ Node found on backup path
 
Node: 0000.0000.0003.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:30
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:40
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:30
Q node: 0000.0000.0006.00-00 primary dist:40
Q node: 0000.0000.0007.00-00 primary dist:20
PQ Node: 0000.0000.0006.00-00 backup dist:1000
 
Node: 0000.0000.0004.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:30
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:40
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:30
Q node: 0000.0000.0006.00-00 primary dist:40
Q node: 0000.0000.0007.00-00 primary dist:20
PQ Node: 0000.0000.0006.00-00 backup dist:1000
 
Node: 0000.0000.0005.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:30
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:40
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:30
Q node: 0000.0000.0006.00-00 primary dist:40
Q node: 0000.0000.0007.00-00 primary dist:20
PQ Node: 0000.0000.0006.00-00 backup dist:1000
 
Node: 0000.0000.0006.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:30
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:40
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:30
Q node: 0000.0000.0006.00-00 primary dist:40
Q node: 0000.0000.0007.00-00 primary dist:20
PQ Node: 0000.0000.0006.00-00 backup dist:1000
 
Node: 0000.0000.0007.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0005.00-00 primary dist:30
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:40
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0005.00-00 primary dist:30
Q node: 0000.0000.0006.00-00 primary dist:40
Q node: 0000.0000.0007.00-00 primary dist:20
PQ Node: 0000.0000.0006.00-00 backup dist:1000
 
P1# P1#show ip isis route tilfa
 
Tag : 1 VRF : default
Codes : L1 - IS-IS level-1, L2 - IS-IS level-2,
C - Connected Routes, ia - IS-IS inter area
 
1.1.1.1/32
L1: Primary Path Nexthop : 10.1.2.1, eth1
Route ftnix :1 ilmix :5
SR Incoming Label : 16001
SR outgoing Label : 3
NO PQ node
NO Backup
 
 
1.1.1.2/32
C: Primary Path Nexthop : 0.0.0.0, lo
Route ftnix :0 ilmix :1
SR Incoming Label : 16002
No SR outgoing Label
NO PQ node
NO Backup
 
 
1.1.1.3/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :2 ilmix :6
SR Incoming Label : 16003
SR outgoing Label : 3
PQ node : 1.1.1.6
Backup ftnix :10 ilmix :47
Backup outgoing Label : 16003
Bypass_trunk id :2203
Backup out interface : eth3
 
 
1.1.1.4/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :3 ilmix :7
SR Incoming Label : 16004
SR outgoing Label : 16004
PQ node : 1.1.1.6
Backup ftnix :11 ilmix :48
Backup outgoing Label : 16004
Bypass_trunk id :2203
Backup out interface : eth3
 
 
1.1.1.5/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :4 ilmix :8
SR Incoming Label : 16005
SR outgoing Label : 16005
PQ node : 1.1.1.6
Backup ftnix :12 ilmix :49
Backup outgoing Label : 16005
Bypass_trunk id :2203
Backup out interface : eth3
 
 
1.1.1.6/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :5 ilmix :15
SR Incoming Label : 16006
SR outgoing Label : 16006
PQ node : 1.1.1.6
Backup ftnix :13 ilmix :50
Backup outgoing Label : 16006
Bypass_trunk id :2203
Backup out interface : eth3
 
Trunk : 2203 :1.1.1.6_nh_10007 ftn_ix : 15 ref_cnt:7
Number Of outgoing label : 1
16006
Nexthop address : 10.2.6.2
 
 
1.1.1.7/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :6 ilmix :40
SR Incoming Label : 16007
SR outgoing Label : 16007
PQ node : 1.1.1.6
Backup ftnix :14 ilmix :53
Backup outgoing Label : 16007
Bypass_trunk id :2203
Backup out interface : eth3
 
P1#
P1#show mpls ilm-table
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
 
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
i> 10.1.2.1/32 2 24960 3 N/A eth1 10.1.2.1 LSP_DEFAULT
i> 1.1.1.4/32 7 16004 16004 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.4/32 48 16004 16004 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.2/32 1 16002 Nolabel N/A N/A 127.0.0.1 LSP_DEFAULT
i> 1.1.1.1/32 5 16001 3 N/A eth1 10.1.2.1 LSP_DEFAULT
i> 1.1.1.3/32 6 16003 3 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.3/32 47 16003 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.6/32 15 16006 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.6/32 50 16006 16006 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.5/32 8 16005 16005 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.5/32 49 16005 16005 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.7/32 40 16007 16007 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.7/32 53 16007 16007 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.3.2/32 3 24961 3 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 10.2.3.2/32 54 24961 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.6.2/32 4 24962 3 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.6.2/32 55 24962 16006 N/A eth2 10.2.6.2 LSP_DEFAULT
P1#
P1#show mpls forwarding-table
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN
 
Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
i> 1.1.1.1/32 1 5 0 Yes LSP_DEFAULT 3 eth1 No 10.1.2.1
i> 1.1.1.3/32 2 3 0 Yes LSP_DEFAULT 3 eth2 No 10.2.3.2
i> 1.1.1.3/32 10 15 0 No LSP_DEFAULT 16003 - No 10.2.6.2
i> 1.1.1.4/32 3 7 0 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
i> 1.1.1.4/32 11 20 0 No LSP_DEFAULT 16004 - No 10.2.6.2
i> 1.1.1.5/32 4 8 0 Yes LSP_DEFAULT 16005 eth2 No 10.2.3.2
i> 1.1.1.5/32 12 21 0 No LSP_DEFAULT 16005 eth3 No 10.2.6.2
i> 1.1.1.6/32 5 10 0 Yes LSP_DEFAULT 16006 eth2 No 10.2.3.2
i> 1.1.1.6/32 13 22 0 No LSP_DEFAULT 16006 eth3 No 10.2.6.2
i> 1.1.1.6/32 15 26 2203 Yes LSP_DEFAULT 16006 eth3 No 10.2.6.2
i> 1.1.1.7/32 6 11 0 Yes LSP_DEFAULT 16007 eth2 No 10.2.3.2
i> 1.1.1.7/32 14 24 0 No LSP_DEFAULT 16007 - No 10.2.6.2
K> 202.1.1.0/24 7 - - - LSP_DEFAULT - eth2 No 1.1.1.7
P1#show mpls ftn-table 1.1.1.6/32
Primary FTN entry with FEC: 1.1.1.6/32, id: 5, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 9, in intf: - in label: 0 out-segment ix: 19
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 19, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth2, transport out intf: N/A, out label: 16006
Nexthop addr: 10.2.3.2 cross connect ix: 9, op code: Push and Lookup
 
 
Non-primary FTN entry with FEC: 1.1.1.6/32, id: 13, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 12, in intf: - in label: 0 out-segment ix: 25
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 25, owner: ISIS-SR, Stale: NO, out intf: eth3, out label: 16006
Nexthop addr: 10.2.6.2 cross connect ix: 12, op code: Push
 
bypass_ftn_ix 15
 
Primary FTN entry with FEC: 1.1.1.6/32, id: 15, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 2203, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 12, in intf: - in label: 0 out-segment ix: 25
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 25, owner: ISIS-SR, Stale: NO, out intf: eth3, out label: 16006
Nexthop addr: 10.2.6.2 cross connect ix: 12, op code: Push
 
P1#
 
P1#show mpls ftn-table 1.1.1.7/32
Primary FTN entry with FEC: 1.1.1.7/32, id: 6, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 4, in intf: - in label: 0 out-segment ix: 4
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 4, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16007
Nexthop addr: 10.2.3.2 cross connect ix: 4, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.7/32, id: 14, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 11, in intf: - in label: 0 out-segment ix: 23
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 23, owner: ISIS-SR, Stale: NO, ISIS-SR out intf: eth3, transport out intf: N/A, out label: 16007
Nexthop addr: 10.2.6.2 cross connect ix: 11, op code: Push and Lookup
 
bypass_ftn_ix 15
 
P1#
Topology
 
TI-LFA FRR path using Adjacent P and Q Nodes
TI-LFA FRR Path using Adjacent P and Q nodes with OSPF-SR
P4
 
P4#configure terminal
Enter configure mode.
P4(config)#interface eth2
Enter interface mode.
P4(config-if)# ip ospf cost 1000
Configure the OSPF cost of the interface
P4(config-if)#exit
Exit interface mode.
P4(config)#exit
Exit configure mode
P4(config)#commit
Commit the candidate configuration to the running configuration.
P3
 
P3#configure terminal
Enter configure mode.
P3(config)#interface eth2
Enter interface mode.
P3(config-if)# ip ospf cost 1000
Configure the OSPF cost of the interface
P3(config-if)#exit
Exit interface mode.
P3(config)#exit
Exit configure mode
P3(config)#commit
Commit the candidate configuration to the running configuration.
Validation
P1
P1#show ip ospf tilfa-backup-path
 
OSPF process 100:
Route [1.1.1.1]
NO PQ node
Route [1.1.1.2]
Route [1.1.1.3]
P-node: 1.1.1.5 Q-node: 1.1.1.4
Route [1.1.1.4]
P-node: 1.1.1.5 Q-node: 1.1.1.4
Route [1.1.1.5]
P-node: 1.1.1.4 Q-node: 1.1.1.5
Route [1.1.1.6]
P-node: 1.1.1.4 Q-node: 1.1.1.5
Route [1.1.1.7]
P-node: 1.1.1.5 Q-node: 1.1.1.4
Route [10.1.2.0]
Route [10.2.3.0]
Route [10.2.6.0]
Route [10.3.4.0]
Route [10.3.7.0]
Route [10.4.5.0]
Route [10.5.6.0]
Neighbor [1.1.1.1]
Neighbor [1.1.1.3]
P-node: 1.1.1.5 Q-node: 1.1.1.4
Neighbor [1.1.1.6]
P-node: 1.1.1.4 Q-node: 1.1.1.5
 
Displaying vertex-info in tilfa_network table
Vertex [1.1.1.1]
P node: 1.1.1.4 dist: 2
P node: 1.1.1.7 dist: 2
P node: 1.1.1.3 dist: 1
P node: 1.1.1.5 dist: 2
P node: 1.1.1.6 dist: 1
 
Vertex [1.1.1.2]
No P Nodes
No Q Nodes
 
Vertex [1.1.1.3]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.5 dist: 2
P node: 1.1.1.6 dist: 1
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.7 dist: 2
P-node: 1.1.1.5 Q-node: 1.1.1.4
Backup out-interface: eth3
 
Vertex [1.1.1.4]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.5 dist: 2
P node: 1.1.1.6 dist: 1
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.7 dist: 2
P-node: 1.1.1.5 Q-node: 1.1.1.4
Backup out-interface: eth3
 
Vertex [1.1.1.5]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.7 dist: 2
P node: 1.1.1.3 dist: 1
Q node: 1.1.1.5 dist: 2
P-node: 1.1.1.4 Q-node: 1.1.1.5
Backup out-interface: eth2
 
Vertex [1.1.1.6]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.4 dist: 2
P node: 1.1.1.7 dist: 2
P node: 1.1.1.3 dist: 1
Q node: 1.1.1.5 dist: 2
P-node: 1.1.1.4 Q-node: 1.1.1.5
Backup out-interface: eth2
 
Vertex [1.1.1.7]
P node: 1.1.1.1 dist: 1
P node: 1.1.1.5 dist: 2
P node: 1.1.1.6 dist: 1
Q node: 1.1.1.4 dist: 2
Q node: 1.1.1.7 dist: 2
P-node: 1.1.1.5 Q-node: 1.1.1.4
Backup out-interface: eth3
 
P1# P1#show ip ospf tilfa-repair-list
 
1.1.1.1/32
Primary Path Metric :2
Primary Path Nexthop : 10.1.2.1, eth1
Route ftnix:1 ilmix:1
SR Incoming Label : 16001
SR outgoing Label : 3
NO PQ node
 
1.1.1.2/32
1.1.1.3/32
Primary Path Metric :2
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:2 ilmix:4
SR Incoming Label : 16003
SR outgoing Label : 3
P-node: 1.1.1.5 Q-node: 1.1.1.4
 
Backup ftnix:8 ilmix:33
Backup outgoing Label : 16003
Bypass_trunk id :101
Backup out interface: eth3
 
1.1.1.4/32
Primary Path Metric :3
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:3 ilmix:5
SR Incoming Label : 16004
SR outgoing Label : 16004
P-node: 1.1.1.5 Q-node: 1.1.1.4
 
Backup ftnix:9 ilmix:34
Backup outgoing Label : 16004
Bypass_trunk id :101
Backup out interface: eth3
 
Bypass-Trunk: 102 Name: 1.1.1.4_1.1.1.5_nexthop__10006 ftn_ix:7
ftn_info->trunk_ftn_ix : 7
Number Of outgoing label 2:
16004
24321
Nexthop address: 10.2.3.2
 
1.1.1.5/32
Primary Path Metric :3
Primary Path Nexthop : 10.2.6.2, eth3
Route ftnix:4 ilmix:6
SR Incoming Label : 16005
SR outgoing Label : 16005
P-node: 1.1.1.4 Q-node: 1.1.1.5
 
Backup ftnix:10 ilmix:35
Backup outgoing Label : 16005
Bypass_trunk id :102
Backup out interface: eth2
 
Bypass-Trunk: 101 Name: 1.1.1.5_1.1.1.4_nexthop__10007 ftn_ix:6
ftn_info->trunk_ftn_ix : 6
Number Of outgoing label 2:
16005
24320
Nexthop address: 10.2.6.2
 
1.1.1.6/32
Primary Path Metric :2
Primary Path Nexthop : 10.2.6.2, eth3
Route ftnix:5 ilmix:8
SR Incoming Label : 16006
SR outgoing Label : 3
P-node: 1.1.1.4 Q-node: 1.1.1.5
 
Backup ftnix:11 ilmix:36
Backup outgoing Label : 16006
Bypass_trunk id :102
Backup out interface: eth2
 
1.1.1.7/32
Primary Path Metric :3
Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix:12 ilmix:15
SR Incoming Label : 16007
SR outgoing Label : 16007
P-node: 1.1.1.5 Q-node: 1.1.1.4
 
Backup ftnix:14 ilmix:37
Backup outgoing Label : 16007
Bypass_trunk id :101
Backup out interface: eth3
 
10.1.2.0/24
10.2.3.0/24
10.2.6.0/24
10.3.4.0/24
10.3.7.0/24
10.4.5.0/24
10.5.6.0/24
P1#
 
P1#show mpls ilm-table
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
 
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
O> 1.1.1.6/32 8 16006 3 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.6/32 36 16006 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.4/32 5 16004 16004 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.4/32 34 16004 16004 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.3/32 4 16003 3 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.3/32 33 16003 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.1/32 1 16001 3 N/A eth1 10.1.2.1 LSP_DEFAULT
O> 1.1.1.5/32 6 16005 16005 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.5/32 35 16005 16005 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 10.1.2.1/32 2 24320 3 N/A eth1 10.1.2.1 LSP_DEFAULT
O> 1.1.1.7/32 15 16007 16007 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.7/32 37 16007 16007 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.3.2/32 3 24321 3 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 10.2.3.2/32 38 24321 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.6.2/32 7 24322 3 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.6.2/32 39 24322 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
P1#
 
P1#show mpls ilm-table
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
 
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
O> 10.1.2.1/32 2 24320 3 N/A eth1 10.1.2.1 LSP_DEFAULT
O> 1.1.1.4/32 8 16004 16004 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.4/32 60 16004 16004 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.3/32 3 16003 3 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.3/32 59 16003 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.1/32 1 16001 3 N/A eth1 10.1.2.1 LSP_DEFAULT
O> 1.1.1.6/32 4 16006 3 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.6/32 62 16006 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.5/32 15 16005 16005 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 1.1.1.5/32 61 16005 16005 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.7/32 7 16007 16007 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 1.1.1.7/32 63 16007 16007 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.3.2/32 5 24321 3 N/A eth2 10.2.3.2 LSP_DEFAULT
O> 10.2.3.2/32 64 24321 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.6.2/32 6 24322 3 N/A eth3 10.2.6.2 LSP_DEFAULT
O> 10.2.6.2/32 65 24322 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
P#
 
P1#show mpls forwarding-table
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN
 
Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
O> 1.1.1.1/32 1 2 0 Yes LSP_DEFAULT 3 eth1 No 10.1.2.1
O> 1.1.1.3/32 2 4 0 Yes LSP_DEFAULT 3 eth2 No 10.2.3.2
O> 1.1.1.3/32 8 13 0 No LSP_DEFAULT 16003 - No 10.2.6.2
O> 1.1.1.4/32 3 6 0 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
O> 1.1.1.4/32 9 15 0 No LSP_DEFAULT 16004 - No 10.2.6.2
O> 1.1.1.4/32 7 11 102 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
O> 1.1.1.5/32 4 8 0 Yes LSP_DEFAULT 16005 eth3 No 10.2.6.2
O> 1.1.1.5/32 10 18 0 No LSP_DEFAULT 16005 - No 10.2.3.2
O> 1.1.1.5/32 6 7 101 Yes LSP_DEFAULT 16005 - No 10.2.6.2
O> 1.1.1.6/32 5 10 0 Yes LSP_DEFAULT 3 eth3 No 10.2.6.2
O> 1.1.1.6/32 11 20 0 No LSP_DEFAULT 16006 - No 10.2.3.2
O> 1.1.1.7/32 12 22 0 Yes LSP_DEFAULT 16007 eth2 No 10.2.3.2
O> 1.1.1.7/32 14 24 0 No LSP_DEFAULT 16007 - No 10.2.6.2
K> 202.1.1.0/24 13 - - - LSP_DEFAULT - eth2 No 1.1.1.7
P1#
 
P1#show mpls ftn-table 1.1.1.5/32
Primary FTN entry with FEC: 1.1.1.5/32, id: 4, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 7, in intf: - in label: 0 out-segment ix: 16
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 16, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth3, transport out intf: N/A, out label: 16005
Nexthop addr: 10.2.6.2 cross connect ix: 7, op code: Push and Lookup
 
 
Non-primary FTN entry with FEC: 1.1.1.5/32, id: 10, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 8, in intf: - in label: 0 out-segment ix: 17
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 17, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth2, transport out intf: N/A, out label: 16005
Nexthop addr: 10.2.3.2 cross connect ix: 8, op code: Push and Lookup
 
bypass_ftn_ix 7
 
Primary FTN entry with FEC: 1.1.1.5/32, id: 6, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 101, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 7, in intf: - in label: 0 out-segment ix: 16
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 16, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth3, transport out intf: N/A, out label: 16005\24320
Nexthop addr: 10.2.6.2 cross connect ix: 7, op code: Push and Lookup
 
 
P1#
 
P1#show mpls ftn-table 1.1.1.4/32
Primary FTN entry with FEC: 1.1.1.4/32, id: 3, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 3, in intf: - in label: 0 out-segment ix: 5
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 5, owner: OSPF-SR, Stale: NO, out intf: eth2, out label: 16004
Nexthop addr: 10.2.3.2 cross connect ix: 3, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.4/32, id: 9, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 6, in intf: - in label: 0 out-segment ix: 14
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 14, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth3, transport out intf: N/A, out label: 16004
Nexthop addr: 10.2.6.2 cross connect ix: 6, op code: Push and Lookup
 
bypass_ftn_ix 6
 
Primary FTN entry with FEC: 1.1.1.4/32, id: 7, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 102, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 3, in intf: - in label: 0 out-segment ix: 5
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 5, owner: OSPF-SR, Stale: NO, out intf: eth2, out label: 16004\24321
Nexthop addr: 10.2.3.2 cross connect ix: 3, op code: Push
 
 
P1#
 
P1#show mpls ftn-table 1.1.1.7/32
Primary FTN entry with FEC: 1.1.1.7/32, id: 12, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 10, in intf: - in label: 0 out-segment ix: 21
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 21, owner: OSPF-SR, Stale: NO, out intf: eth2, out label: 16007
Nexthop addr: 10.2.3.2 cross connect ix: 10, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.7/32, id: 14, row status: Active, Tunnel-Policy: N/A
Owner: OSPF-SR, distance: 110, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 11, in intf: - in label: 0 out-segment ix: 23
Owner: OSPF-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 23, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth3, transport out intf: N/A, out label: 16007
Nexthop addr: 10.2.6.2 cross connect ix: 11, op code: Push and Lookup
 
bypass_ftn_ix 6
 
P1#
TI-LFA FRR Path using Adjacent P and Q nodes with ISIS-SR
P4
 
P4#configure terminal
Enter configure mode.
P4(config)#interface eth2
Enter interface mode.
P4(config-if)#isis wide-metric 1000
Configure the ISIS wide-metric for the interface
P4(config-if)#exit
Exit interface mode.
P4(config)#exit
Exit configure mode
P4(config)#commit
Commit the candidate configuration to the running configuration.
P3
 
P3#configure terminal
Enter configure mode.
P3(config)#interface eth2
Enter interface mode.
P3(config-if)#isis wide-metric 1000
Configure the ISIS wide-metric for the interface
P3(config-if)#exit
Exit interface mode.
P3(config)#exit
Exit configure mode
P3(config)#commit
Commit the candidate configuration to the running configuration.
Validation
P1
P1#show isis tilfa pq
 
IS-IS Level-1 Link State Database:
 
Node: 0000.0000.0001.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0003.00-00 primary dist:10
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:10
No PQ Node found on backup path
 
Node: 0000.0000.0003.00-00
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0007.00-00 primary dist:20
P-Node: 0000.0000.0005.00-00 backup dist:20
Q-Node: 0000.0000.0004.00-00 backup dist:1020
 
Node: 0000.0000.0004.00-00
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0007.00-00 primary dist:20
P-Node: 0000.0000.0005.00-00 backup dist:20
Q-Node: 0000.0000.0004.00-00 backup dist:1020
 
Node: 0000.0000.0005.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0003.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0005.00-00 primary dist:20
P-Node: 0000.0000.0004.00-00 backup dist:20
Q-Node: 0000.0000.0005.00-00 backup dist:1020
 
Node: 0000.0000.0006.00-00
P node: 0000.0000.0004.00-00 primary dist:20
P node: 0000.0000.0007.00-00 primary dist:20
P node: 0000.0000.0003.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0005.00-00 primary dist:20
P-Node: 0000.0000.0004.00-00 backup dist:20
Q-Node: 0000.0000.0005.00-00 backup dist:1020
 
Node: 0000.0000.0007.00-00
P node: 0000.0000.0005.00-00 primary dist:20
P node: 0000.0000.0006.00-00 primary dist:10
P node: 0000.0000.0001.00-00 primary dist:10
Q node: 0000.0000.0004.00-00 primary dist:20
Q node: 0000.0000.0007.00-00 primary dist:20
P-Node: 0000.0000.0005.00-00 backup dist:20
Q-Node: 0000.0000.0004.00-00 backup dist:1020
 
P1#
 
P1#show ip isis route tilfa
 
Tag : 1 VRF : default
Codes : L1 - IS-IS level-1, L2 - IS-IS level-2,
C - Connected Routes, ia - IS-IS inter area
 
1.1.1.1/32
L1: Primary Path Nexthop : 10.1.2.1, eth1
Route ftnix :1 ilmix :5
SR Incoming Label : 16001
SR outgoing Label : 3
NO PQ node
NO Backup
 
 
1.1.1.2/32
C: Primary Path Nexthop : 0.0.0.0, lo
Route ftnix :0 ilmix :1
SR Incoming Label : 16002
No SR outgoing Label
NO PQ node
NO Backup
 
 
1.1.1.3/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :2 ilmix :6
SR Incoming Label : 16003
SR outgoing Label : 3
P node : 1.1.1.5
Q node : 1.1.1.4
Backup ftnix :10 ilmix :47
Backup outgoing Label : 16003
Bypass_trunk id :2203
Backup out interface : eth3
 
 
1.1.1.4/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :3 ilmix :7
SR Incoming Label : 16004
SR outgoing Label : 16004
P node : 1.1.1.5
Q node : 1.1.1.4
Backup ftnix :11 ilmix :48
Backup outgoing Label : 16004
Bypass_trunk id :2203
Backup out interface : eth3
 
Trunk : 2204 :1.1.1.4_1.1.1.5_nh_10006 ftn_ix : 16 ref_cnt:3
Number Of outgoing label : 2
16004
24960
Nexthop address : 10.2.3.2
 
 
1.1.1.5/32
L1: Primary Path Nexthop : 10.2.6.2, eth3
Route ftnix :4 ilmix :8
SR Incoming Label : 16005
SR outgoing Label : 16005
P node : 1.1.1.4
Q node : 1.1.1.5
Backup ftnix :12 ilmix :49
Backup outgoing Label : 16005
Bypass_trunk id :2204
Backup out interface : eth2
 
Trunk : 2203 :1.1.1.5_1.1.1.4_nh_10007 ftn_ix : 15 ref_cnt:4
Number Of outgoing label : 2
16005
24961
Nexthop address : 10.2.6.2
 
 
1.1.1.6/32
L1: Primary Path Nexthop : 10.2.6.2, eth3
Route ftnix :5 ilmix :15
SR Incoming Label : 16006
SR outgoing Label : 3
P node : 1.1.1.4
Q node : 1.1.1.5
Backup ftnix :13 ilmix :50
Backup outgoing Label : 16006
Bypass_trunk id :2204
Backup out interface : eth2
 
 
1.1.1.7/32
L1: Primary Path Nexthop : 10.2.3.2, eth2
Route ftnix :6 ilmix :40
SR Incoming Label : 16007
SR outgoing Label : 16007
P node : 1.1.1.5
Q node : 1.1.1.4
Backup ftnix :14 ilmix :53
Backup outgoing Label : 16007
Bypass_trunk id :2203
Backup out interface : eth3
 
P1#
 
P1# show mpls ilm-table
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
 
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
i> 10.1.2.1/32 2 24960 3 N/A eth1 10.1.2.1 LSP_DEFAULT
i> 1.1.1.4/32 7 16004 16004 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.4/32 48 16004 16004 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.2/32 1 16002 Nolabel N/A N/A 127.0.0.1 LSP_DEFAULT
i> 1.1.1.1/32 5 16001 3 N/A eth1 10.1.2.1 LSP_DEFAULT
i> 1.1.1.3/32 6 16003 3 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.3/32 47 16003 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.6/32 15 16006 3 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.6/32 50 16006 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.5/32 8 16005 16005 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 1.1.1.5/32 49 16005 16005 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.7/32 40 16007 16007 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.7/32 53 16007 16007 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.3.2/32 3 24961 3 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 10.2.3.2/32 60 24961 16003 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.6.2/32 4 24962 3 N/A eth3 10.2.6.2 LSP_DEFAULT
i> 10.2.6.2/32 61 24962 16006 N/A eth2 10.2.3.2 LSP_DEFAULT
P1#
 
P1#show mpls forwarding-table
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN
 
Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
i> 1.1.1.1/32 1 5 0 Yes LSP_DEFAULT 3 eth1 No 10.1.2.1
i> 1.1.1.3/32 2 3 0 Yes LSP_DEFAULT 3 eth2 No 10.2.3.2
i> 1.1.1.3/32 10 15 0 No LSP_DEFAULT 16003 - No 10.2.6.2
i> 1.1.1.4/32 3 7 0 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
i> 1.1.1.4/32 11 20 0 No LSP_DEFAULT 16004 - No 10.2.6.2
i> 1.1.1.4/32 16 26 2204 Yes LSP_DEFAULT 16004 eth2 No 10.2.3.2
i> 1.1.1.5/32 4 8 0 Yes LSP_DEFAULT 16005 eth3 No 10.2.6.2
i> 1.1.1.5/32 12 21 0 No LSP_DEFAULT 16005 - No 10.2.3.2
i> 1.1.1.5/32 15 25 2203 Yes LSP_DEFAULT 16005 eth3 No 10.2.6.2
i> 1.1.1.6/32 5 10 0 Yes LSP_DEFAULT 3 eth3 No 10.2.6.2
i> 1.1.1.6/32 13 22 0 No LSP_DEFAULT 16006 - No 10.2.3.2
i> 1.1.1.7/32 6 11 0 Yes LSP_DEFAULT 16007 eth2 No 10.2.3.2
i> 1.1.1.7/32 14 24 0 No LSP_DEFAULT 16007 - No 10.2.6.2
K> 202.1.1.0/24 7 - - - LSP_DEFAULT - eth2 No 1.1.1.7
P1#
 
P1#show mpls ftn-table
Primary FTN entry with FEC: 1.1.1.1/32, id: 1, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 1, in intf: - in label: 0 out-segment ix: 1
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 1, owner: N/A, Stale: NO, out intf: eth1, out label: 3
Nexthop addr: 10.1.2.1 cross connect ix: 1, op code: Push
 
 
Primary FTN entry with FEC: 1.1.1.3/32, id: 2, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 2, in intf: - in label: 0 out-segment ix: 2
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 2, owner: N/A, Stale: NO, out intf: eth2, out label: 3
Nexthop addr: 10.2.3.2 cross connect ix: 2, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.3/32, id: 10, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 6, in intf: - in label: 0 out-segment ix: 14
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 14, owner: ISIS-SR, Stale: NO, ISIS-SR out intf: eth3, transport out intf: N/A, out label: 16003
Nexthop addr: 10.2.6.2 cross connect ix: 6, op code: Push and Lookup
 
bypass_ftn_ix 15
 
Primary FTN entry with FEC: 1.1.1.4/32, id: 3, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 3, in intf: - in label: 0 out-segment ix: 6
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 6, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16004
Nexthop addr: 10.2.3.2 cross connect ix: 3, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.4/32, id: 11, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 10, in intf: - in label: 0 out-segment ix: 18
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 18, owner: ISIS-SR, Stale: NO, ISIS-SR out intf: eth3, transport out intf: N/A, out label: 16004
Nexthop addr: 10.2.6.2 cross connect ix: 10, op code: Push and Lookup
 
bypass_ftn_ix 15
 
Primary FTN entry with FEC: 1.1.1.4/32, id: 16, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 2204, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 3, in intf: - in label: 0 out-segment ix: 6
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 6, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16004\24960
Nexthop addr: 10.2.3.2 cross connect ix: 3, op code: Push
 
 
Primary FTN entry with FEC: 1.1.1.5/32, id: 4, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 7, in intf: - in label: 0 out-segment ix: 16
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 16, owner: OSPF-SR, Stale: NO, out intf: eth3, out label: 16005
Nexthop addr: 10.2.6.2 cross connect ix: 7, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.5/32, id: 12, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 8, in intf: - in label: 0 out-segment ix: 17
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 17, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth2, transport out intf: N/A, out label: 16005
Nexthop addr: 10.2.3.2 cross connect ix: 8, op code: Push and Lookup
 
bypass_ftn_ix 16
 
Primary FTN entry with FEC: 1.1.1.5/32, id: 15, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 2203, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 7, in intf: - in label: 0 out-segment ix: 16
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 16, owner: OSPF-SR, Stale: NO, out intf: eth3, out label: 16005\24961
Nexthop addr: 10.2.6.2 cross connect ix: 7, op code: Push
 
 
Primary FTN entry with FEC: 1.1.1.6/32, id: 5, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 5, in intf: - in label: 0 out-segment ix: 9
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 9, owner: N/A, Stale: NO, out intf: eth3, out label: 3
Nexthop addr: 10.2.6.2 cross connect ix: 5, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.6/32, id: 13, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 9, in intf: - in label: 0 out-segment ix: 19
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 19, owner: OSPF-SR, Stale: NO, OSPF-SR out intf: eth2, transport out intf: N/A, out label: 16006
Nexthop addr: 10.2.3.2 cross connect ix: 9, op code: Push and Lookup
 
bypass_ftn_ix 16
 
Primary FTN entry with FEC: 1.1.1.7/32, id: 6, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 4, in intf: - in label: 0 out-segment ix: 4
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 4, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16007
Nexthop addr: 10.2.3.2 cross connect ix: 4, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.7/32, id: 14, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 11, in intf: - in label: 0 out-segment ix: 23
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 23, owner: ISIS-SR, Stale: NO, ISIS-SR out intf: eth3, transport out intf: N/A, out label: 16007
Nexthop addr: 10.2.6.2 cross connect ix: 11, op code: Push and Lookup
 
bypass_ftn_ix 15
 
Primary FTN entry with FEC: 202.1.1.0/24, id: 7, row status: Active, Tunnel-Policy: N/A
Owner: CLI, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Transport Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 4, in intf: - in label: 0 out-segment ix: 4
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 4, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16007
Nexthop addr: 10.2.3.2 cross connect ix: 4, op code: Push
 
P1#
TI-LFA FRR for SR-Policy
The active segment of a packet (ie., the top label of the packet as seen by the receiving router) that is being forwarded using an SR-policy can be protected upon failure of its primary outgoing interface by enabling FRR for the SR-policy.
P1
 
P1#configure terminal
Enter configure mode
P1(config)#segment-routing
Configuring segment-routing
P1(config-sr)#traffic-engineering
Segment Routing traffic engineering
P1(config-sr-te)#segment-list p5-p4-pe2
Configure a segment-list
P1(config-sr-sl)#index 10 segment-type-1 16006
 
Configure the segment-list entry with index 10 and label as prefix-sid of P5
P1(config-sr-sl)#index 20 segment-type-1 16005
 
Configure the segment-list entry with index 10 and label as prefix-sid of P4
P1(config-sr-sl)#index 30 segment-type-1 16007
 
Configure the segment-list entry with index 10 and label as prefix-sid of PE2
P1(config-sr-sl)#exit-sr-sl
Exit segment-routing segment-list mode
P1(config-sr-te)#policy to-pe2
Configure an SR-policy
P1(config-sr-pol)#color 11 end-point 1.1.1.7
 
Configure SR-policy with key ie., color and end-point
P1(config-sr-pol)#candidate-path 11
Configure a candidate-path for the SR-policy
P1(config-sr-pol-cp)#preference 100
Configure the preference value for the candidate-path
P1(config-sr-pol-cp)#explicit segment-list p5-p4-pe2
Configure the candidate-path as explicit-path with segment- list
P1(config-sr-pol-cp)#exit-pol-cp
Exit from SR policy candidate path configuration mode
P1(config-sr-pol)#exit-sr-pol
Exit from SR policy configuration mode
P1(config-sr-te)#policy-fast-reroute-enable
Enable segment-routing policy fast-reroute
P1(config-sr-te)#exit
Exit segment-routing mode
P1(config)#exit
Exit configure terminal mode
P1(config)#commit
Commit the candidate configuration to the running configuration.
Validation
P1
 
P1#show mpls forwarding-table 1.1.1.7/32
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN
 
Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
P> 1.1.1.7/32 8 13 1 Yes LSP_DEFAULT 3 eth3 No 10.2.6.2
P> 1.1.1.7/32 9 24 1 No LSP_DEFAULT 16006 - No 10.2.3.2
i 1.1.1.7/32 6 4 0 Yes LSP_DEFAULT 16007 eth2 No 10.2.3.2
i 1.1.1.7/32 14 23 0 No LSP_DEFAULT 16007 - No 10.2.6.2
P1#
 
P1#show mpls ftn-table 1.1.1.7/32
Primary FTN entry with FEC: 1.1.1.7/32, id: 8, row status: Active, Tunnel-Policy: N/A
Owner: SR_POLICY, distance: 0, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 1, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 12, in intf: - in label: 0 out-segment ix: 12
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 12, owner: N/A, Stale: NO, out intf: eth3, out label: 3\16005\16007
Nexthop addr: 10.2.6.2 cross connect ix: 12, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.7/32, id: 9, row status: Active, Tunnel-Policy: N/A
Owner: SR_POLICY, distance: 0, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 1, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 13, in intf: - in label: 0 out-segment ix: 11
Owner: SR_POLICY, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 11, owner: SR_POLICY, Stale: NO, SR_POLICY out intf: eth2, transport out intf: N/A, out label: 16006\16005\16007
Nexthop addr: 10.2.3.2 cross connect ix: 13, op code: Push and Lookup
 
bypass_ftn_ix 16
 
Primary FTN entry with FEC: 1.1.1.7/32, id: 6, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A, Color: 0
Cross connect ix: 4, in intf: - in label: 0 out-segment ix: 4
Owner: ISIS-SR, Persistent: No, Admin Status: Down, Oper Status: Down
Out-segment with ix: 4, owner: ISIS-SR, Stale: NO, out intf: eth2, out label: 16007
Nexthop addr: 10.2.3.2 cross connect ix: 4, op code: Push
 
 
Non-primary FTN entry with FEC: 1.1.1.7/32, id: 14, row status: Active, Tunnel-Policy: N/A
Owner: ISIS-SR, distance: 115, Action-type: Redirect to Tunnel, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, QoS Resource id: 0, Description: N/A, Color: 0
Cross connect ix: 11, in intf: - in label: 0 out-segment ix: 23
Owner: ISIS-SR, Persistent: No, Admin Status: Down, Oper Status: Down
Out-segment with ix: 23, owner: ISIS-SR, Stale: NO, ISIS-SR out intf: eth3, transport out intf: N/A, out label: 16007
Nexthop addr: 10.2.6.2 cross connect ix: 11, op code: Push and Lookup
 
bypass_ftn_ix 15
 
P1#
 
 
P1#show mpls ilm-table 1.1.1.7/32
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
 
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
i> 1.1.1.7/32 40 16007 16007 N/A eth2 10.2.3.2 LSP_DEFAULT
i> 1.1.1.7/32 53 16007 16007 N/A eth3 10.2.6.2 LSP_DEFAULT
P> 1.1.1.7/32 62 25600 16005 N/A eth3 10.2.6.2 LSP_DEFAULT
P1#