VxLAN Trunk Access Port Configuration
In VxLAN, most of the use cases demand to carry the complete traffic received on the access interface to another VTEP access-port. Hence this support of accepting all tagged and untagged traffic received on the mapped physical port.
Topology
VxLAN Trunk Access Port Configuration topology
Base Configuration - L2 VxLAN
VTEP1
Hardware profile and generic configuration:
#configure terminal | Enter Configure mode. |
(config)#hardware-profile filter vxlan enable | Enable hardware-profile filter for VxLAN. |
(config)#hardware-profile filter egress-ipv4 enable | Enable hardware-profile filter for egress IPv4. |
(config)#hardware-profile statistics ac-lif enable | Enable ac-lif for vxlan access-if port counters |
(config)#qos enable | Enable qos |
(config)#commit | Committing the configurations |
Interface and loopback configuration:
(config)#interface xe7 | Enter Interface mode for xe7 |
(config-if)#switchport | Make it L2 interface |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)#interface xe8 | Enter Interface mode for xe8 |
(config-if)#ip add 10.10.10.1/24 | Configuring the ip address in the network side |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)#interface lo | Enter Interface mode for lo |
(config-if)#ip address 1.1.1.1/32 secondary | Configure loopback ip address as 1.1.1.1 for VTEP1 |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)#commit | Committing the interface configurations |
OSPF configuration:
(config)#router ospf 1 | Enter into router OSPF mode |
(config-router)#ospf router-id 1.1.1.1 | Configure router-id as 1.1.1.1 (lo ip address) |
(config-router)#network 1.1.1.1/32 area 0.0.0.0 | Add 1.1.1.1 (lo ip address) network into area 0 |
(config-router)#network 10.10.10.0/24 area 0.0.0.0 | Add 10.10.10.0(Spine) network into area 0 |
(config-router)#bfd all-interfaces | Enabling bfd on all ospf interface for fast convergence |
(config-router)#exit | Exit Interface mode and return to Configure mode. |
(config)#commit | Committing the ospf configurations |
BGP configuration:
(config)#router bgp 1 | Enter into Router BGP mode |
(config-router)#bgp router-id 1.1.1.1 | Configure router-id as 1.1.1.1 (lo ip address) |
(config-router)#neighbor 2.2.2.2 remote-as 1 | Specify a VTEP2 loopback ip address and remote-as defined |
(config-router)#neighbor 2.2.2.2 update-source lo | Configure update as loopback for VTEP2 |
(config-router)#neighbor 2.2.2.2 advertisement-interval 0 | Configure advertisement-interval as 0 for fast convergence for VTEP2 |
(config-router)#address-family l2vpn evpn | Enter into l2vpn EVPN address family mode |
(config-router-af)#neighbor 2.2.2.2 activate | Activate 2.2.2.2(VTEP2) into l2vpn evpn address family mode |
(config-router-af)#exit-address-family | Exit from l2vpn address family mode |
(config-router)#exit | Exit from Router BGP mode and enter into config mode |
(config)#commit | Committing the bgp configurations |
L2 MAC VRF Configuration:
(config)#mac vrf L2VRF1 | Create mac routing/forwarding instance with L2VRF1 name and enter into vrf mode |
(config-vrf)#rd 1.1.1.1:1 | Assign RD value |
(config-vrf)#route-target both 1:1 | Assign route-target value for same for import and export. Should be same on all node for L2VRF1 |
(config-vrf)#exit | Exit from vrf mode |
(config)#commit | Committing the vrf configurations |
L2 VxLAN configuration:
(config)#nvo vxlan enable | Enable VxLAN |
(config)#nvo vxlan vtep-ip-global 1.1.1.1 | Configure Source vtep-ip-global configuration - Use loopback ip address |
(config)#nvo vxlan id 100 ingress-replication | Configure VxLAN Network identifier without inner-vid- disabled configured for vxlan trunk access port and enter into VxLAN tenant mode |
(config-nvo)#vxlan host-reachability-protocol evpn-bgp L2VRF1 | Assign vrf for evpn-bgp to carry EVPN route |
(config-nvo)#exit | Exit from VxLAN tenant mode and enter into configuration mode. |
(config)#commit | Committing the vxlan configurations |
VTEP2
Hardware profile and generic configuration:
#configure terminal | Enter Configure mode. |
(config)#hardware-profile filter vxlan enable | Enable hardware-profile filter for VxLAN. |
(config)#hardware-profile filter egress-ipv4 enable | Enable hardware-profile filter for egress IPv4. |
(config)#hardware-profile statistics ac-lif enable | Enable ac-lif for vxlan access-if port counters |
(config)#qos enable | Enable qos |
(config)#commit | Committing the configurations |
Interface and loopback configuration:
(config)#interface xe23 | Enter Interface mode for xe23 |
(config-if)#switchport | Make it L2 interface |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)#interface xe14 | Enter Interface mode for xe14 |
(config-if)#ip add 20.20.20.1/24 | Configuring the ip address in the network side |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)#interface lo | Enter Interface mode for lo |
(config-if)#ip address 2.2.2.2/32 secondary | Configure loopback ip address as 2.2.2.2 for VTEP2 |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)#commit | Committing the interface configurations |
OSPF configuration:
(config)#router ospf 1 | Enter into router OSPF mode |
(config-router)#ospf router-id 2.2.2.2 | Configure router-id as 2.2.2.2 (lo ip address) |
(config-router)#network 2.2.2.2/32 area 0.0.0.0 | Add 2.2.2.2 (lo ip address) network into area 0 |
(config-router)#network 20.20.20.0/24 area 0.0.0.0 | Add 20.20.20.0(Spine) network into area 0 |
(config-router)#bfd all-interfaces | Enabling bfd on all ospf interface for fast convergence |
(config-router)#exit | Exit Interface mode and return to Configure mode. |
(config)#commit | Committing the ospf configurations |
BGP configuration:
(config)#router bgp 1 | Enter into Router BGP mode |
(config-router)#bgp router-id 2.2.2.2 | Configure router-id as 2.2.2.2 (lo ip address) |
(config-router)#neighbor 1.1.1.1 remote-as 1 | Specify a VTEP1 loopback ip address and remote-as defined |
(config-router)#neighbor 1.1.1.1 update-source lo | Configure update as loopback for VTEP2 |
(config-router)#neighbor 1.1.1.1 advertisement-interval 0 | Configure advertisement-interval as 0 for fast convergence for VTEP1 |
(config-router)#address-family l2vpn evpn | Enter into l2vpn EVPN address family mode |
(config-router-af)#neighbor 1.1.1.1 activate | Activate 1.1.1.1(VTEP1) into l2vpn evpn address family mode |
(config-router-af)#exit-address-family | Exit from l2vpn address family mode |
(config-router)#exit | Exit from Router BGP mode and enter into config mode |
(config)#commit | Committing the bgp configurations |
L2 MAC VRF Configuration:
(config)#mac vrf L2VRF1 | Create mac routing/forwarding instance with L2VRF1 name and enter into vrf mode |
(config-vrf)#rd 2.2.2.2:1 | Assign RD value |
(config-vrf)#route-target both 1:1 | Assign route-target value for same for import and export. Should be same on all node for L2VRF1 |
(config-vrf)#exit | Exit from vrf mode |
(config)#commit | Committing the vrf configurations |
L2 VxLAN configuration:
(config)#nvo vxlan enable | Enable VxLAN |
(config)#nvo vxlan vtep-ip-global 2.2.2.2 | Configure Source vtep-ip-global configuration - Use loopback ip address |
(config)#nvo vxlan id 100 ingress-replication | Configure VxLAN Network identifier without inner-vid- disabled configured for vxlan trunk access port and enter into VxLAN tenant mode |
(config-nvo)#vxlan host-reachability-protocol evpn-bgp L2VRF1 | Assign vrf for evpn-bgp to carry EVPN route |
(config-nvo)#exit | Exit from VxLAN tenant mode and enter into configuration mode. |
(config)#commit | Committing the vxlan configurations |
SPINE
Spine node where all VTEPs are connected.
Generic configuration:
#configure terminal | Enter Configure mode. |
(config)#qos enable | Enabling qos |
(config)#commit | Committing the configuration |
Interface configuration:
(config)#interface xe8 | Enter Interface mode for xe8 |
(config-if)#ip address 10.10.10.2/24 | Configure ip address as 10.10.10.2 on network side of VTEP1 |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config) interface xe14 | Enter into ce5/1 interface mode |
(config-if)#ip address 20.20.20.2/24 | Configure ip address as 20.20.20.2 on network side of VTEP2 |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config) commit | Committing the configuration |
OSPF configuration:
(config)#router ospf 1 | Enter into router OSPF mode |
(config-router)#ospf router-id 3.3.3.3 | Configure router-id as 3.3.3.3 |
(config-router)#network 10.10.10.0/24 area 0.0.0.0 | Add 10.10.10.0 (VTEP1) network into area 0 |
(config-router)#network 20.20.20.0/24 area 0.0.0.0 | Add 20.20.20.0 (VTEP2) network into area 0 |
(config-router)#bfd all-interfaces | Enabling bfd on all ospf interface for fast convergence |
(config-if)#exit | Exit Interface mode and return to Configure mode. |
(config)commit | Committing the ospf configuration |
VxLAN Trunk Access port as default
In VxLAN, most of the use cases demand to carry the complete traffic received on the access interface to another VTEP access-port. Hence this support of accepting all tagged and untagged traffic received on the mapped physical port.
VTEP1
(config)#nvo vxlan access-if port xe7 default | Configuring the vxlan access port as default to receive untagged, single and double tagged traffic |
(config-nvo-acc-if)#map vnid 100 | Map VxLAN Identified to access-port for VxLAN |
(config-nvo-acc-if)#arp-cache disable | Disable arp-cache - mandatory |
(config-nvo-acc-if)#nd-cache disable | Disable nd-cache - mandatory |
(config-nvo-acc-if)# mac 0000.1111.0001 | Configure static mac-only |
(config-nvo-acc-if)#exit | Exit from VxLAN access-interface mode and enter into configuration mode |
(config)#commit | Committing the vxlan configuration |
VTEP2
(config)#nvo vxlan access-if port xe23 default | Configuring the vxlan access port as default to receive untagged, single and double tagged traffic |
(config-nvo-acc-if)#map vnid 100 | Map VxLAN Identified to access-port for VxLAN |
(config-nvo-acc-if)#arp-cache disable | Disable arp-cache - mandatory |
(config-nvo-acc-if)#nd-cache disable | Disable nd-cache - mandatory |
(config-nvo-acc-if)# mac 0000.2222.0001 | Configure static mac-only |
(config-nvo-acc-if)#exit | Exit from VxLAN access-interface mode and enter into configuration mode |
(config)#commit | Committing the vxlan configuration |
Validation
VTEP1
VTEP1#sh run nvo vxlan
!
nvo vxlan enable
!
nvo vxlan vtep-ip-global 1.1.1.1
!
nvo vxlan id 100 ingress-replication
vxlan host-reachability-protocol evpn-bgp L2VRF1
!
nvo vxlan access-if port xe7 default
map vnid 100
arp-cache disable
nd-cache disable
mac 0000.1111.0001
!
!
VTEP1#sh nvo vxlan tunnel
VxLAN Network tunnel Entries
Source Destination Status Up/Down Update
============================================================================
1.1.1.1 2.2.2.2 Installed 00:02:49 00:02:49
Total number of entries are 1
VTEP1#sh nvo vxlan mac-table
==========================================================================================================================================
VxLAN MAC Entries
==========================================================================================================================================
VNID Interface VlanId Vlan-RangeId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status AccessPortDesc
__________________________________________________________________________________________________________________________________________
100 xe7 ---- ---- ---- 0000.1111.0001 1.1.1.1 Static Local ------- -------
100 ---- ---- ---- 0000.2222.0001 2.2.2.2 Static Remote ------- -------
100 xe7 ---- ---- ---- b0da.1d10.6496 1.1.1.1 Dynamic Local ------- -------
Total number of entries are : 3
VTEP1#sh nvo vxlan mac-table hardware
==========================================================================================================================================
VxLAN MAC Entries
==========================================================================================================================================
VNID Interface VlanId Vlan-RangeId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status Time-out AccessPortDesc
_________________________________________________________________________________________________________________________________________
100 xe7 ---- ---- 0000.1111.0001 1.1.1.1 Static Local ------- --- -------
100 --- ---- ---- 0000.2222.0001 2.2.2.2 Remote ------- --- -------
100 xe7 ---- ---- b0da.1d10.6496 1.1.1.1 Dynamic Local ------- 300 -------
Total number of entries are 3
VTEP1#show nvo vxlan
VxLAN Information
=================
Codes: NW - Network Port
AC - Access Port
(u) - Untagged
VNID VNI-Name VNI-Type Type Interface ESI VLAN DF-Status Src-Addr Dst-Addr
_______________________________________________________________________________________________________________________________
100 ---- L2 NW ---- ---- ---- ---- 1.1.1.1 2.2.2.2
100 ---- -- AC xe7 --- Single Homed Port --- ---- ---- ---- ----
Total number of entries are 2
VTEP1#sh nvo vxlan route-count
VxLAN Active route count information
====================================
Max route count : 32768
Active route count: 3
---------------------------------------------
VNID Total MACONLY MACIPv4 MACIPv6
---------------------------------------------
100 3 3 0 0
Total number of entries are 1
VTEP1#sh nvo vxlan access-if-config
nvo vxlan access-if port xe7 default
map vnid 100
arp-cache disable
nd-cache disable
mac 0000.1111.0001
!
VTEP1#sh nvo vxlan access-if brief
Inner Admin Link
Interface Vlan vlan Ifindex Vnid status status
-----------------------------------------------------------
xe7 --- --- 500000 100 up up
Total number of entries are 1
VTEP1#sh bgp l2vpn evpn summary
BGP router identifier 1.1.1.1, local AS number 1
BGP table version is 2
1 BGP AS-PATH entries
0 BGP community entries
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd AD MACIP MCAST ESI PREFIX-ROUTE
2.2.2.2 4 1 15 17 2 0 0 00:04:52 2 0 1 1 0 0
Total number of neighbors 1
Total number of Established sessions 1
VTEP1#sh bgp l2vpn evpn
BGP table version is 2, local router ID is 1.1.1.1
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal,
l - labeled, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
[EVPN route type]:[ESI]:[VNID]:[relevent route informantion]
1 - Ethernet Auto-discovery Route
2 - MAC/IP Route
3 - Inclusive Multicast Route
4 - Ethernet Segment Route
5 - Prefix Route
Network Next Hop Metric LocPrf Weight Path Peer Encap
RD[1.1.1.1:1] VRF[L2VRF1]:
*> [2]:[0]:[100]:[48,0000:1111:0001]:[0]:[100]
1.1.1.1 0 100 32768 i ---------- VxLAN
* i [2]:[0]:[100]:[48,0000:2222:0001]:[0]:[100]
2.2.2.2 0 100 0 i 2.2.2.2 VxLAN
*> [2]:[0]:[100]:[48,b0da:1d10:6496]:[0]:[100]
1.1.1.1 0 100 32768 i ---------- VxLAN
*> [3]:[100]:[32,1.1.1.1]
1.1.1.1 0 100 32768 i ---------- VxLAN
* i [3]:[100]:[32,2.2.2.2]
2.2.2.2 0 100 0 i 2.2.2.2 VxLAN
RD[2.2.2.2:1]
*>i [2]:[0]:[100]:[48,0000:2222:0001]:[0]:[100]
2.2.2.2 0 100 0 i 2.2.2.2 VxLAN
*>i [3]:[100]:[32,2.2.2.2]
2.2.2.2 0 100 0 i 2.2.2.2 VxLAN
Total number of prefixes 7
VTEP1#sh nvo vxlan arp-cache
VxLAN ARP-CACHE Information
===========================
VNID Ip-Addr Mac-Addr Type Age-Out Retries-Left
____________________________________________________________________________
Total number of entries are 0
VTEP1#sh nvo vxlan nd-cache
VxLAN ND-CACHE Information
===========================
VNID Ip-Addr Mac-Addr Type Age-Out Retries-Left
____________________________________________________________________________________________________
Total number of entries are 0
VTEP1#
VTEP2
VTEP2#sh run nvo vxlan
!
nvo vxlan enable
!
nvo vxlan vtep-ip-global 2.2.2.2
!
nvo vxlan id 100 ingress-replication
vxlan host-reachability-protocol evpn-bgp L2VRF1
!
nvo vxlan access-if port xe23 default
map vnid 100
arp-cache disable
nd-cache disable
mac 0000.2222.0001
!
!
VTEP2#sh nvo vxlan tunnel
VxLAN Network tunnel Entries
Source Destination Status Up/Down Update
============================================================================
2.2.2.2 1.1.1.1 Installed 00:05:47 00:05:47
Total number of entries are 1
VTEP2#sh nvo vxlan
VxLAN Information
=================
Codes: NW - Network Port
AC - Access Port
(u) - Untagged
VNID VNI-Name VNI-Type Type Interface ESI VLAN DF-Status Src-Addr Dst-Addr
_______________________________________________________________________________________________________________________________
100 ---- L2 NW ---- ---- ---- ---- 2.2.2.2 1.1.1.1
100 ---- -- AC xe23 --- Single Homed Port --- ---- ---- ---- ----
Total number of entries are 2
VTEP2#sh nvo vxlan mac-table
==========================================================================================================================================
VxLAN MAC Entries
==========================================================================================================================================
VNID Interface VlanId Vlan-RangeId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status AccessPortDesc
__________________________________________________________________________________________________________________________________________
100 ---- ---- ---- 0000.1111.0001 1.1.1.1 Static Remote ------- -------
100 xe23 ---- ---- ---- 0000.2222.0001 2.2.2.2 Static Local ------- -------
100 ---- ---- ---- b0da.1d10.6496 1.1.1.1 Dynamic Remote ------- -------
Total number of entries are : 3
VTEP2#sh nvo vxlan mac-table hardware
==========================================================================================================================================
VxLAN MAC Entries
==========================================================================================================================================
VNID Interface VlanId Vlan-RangeId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status Time-out AccessPortDesc
_________________________________________________________________________________________________________________________________________
100 --- ---- ---- 0000.1111.0001 1.1.1.1 Remote ------- --- -------
100 xe23 ---- ---- 0000.2222.0001 2.2.2.2 Static Local ------- --- -------
100 --- ---- ---- b0da.1d10.6496 1.1.1.1 Remote ------- --- -------
Total number of entries are 3
VTEP2#sh nvo vxlan route-count
VxLAN Active route count information
====================================
Max route count : 32768
Active route count: 3
---------------------------------------------
VNID Total MACONLY MACIPv4 MACIPv6
---------------------------------------------
100 3 3 0 0
Total number of entries are 1
VTEP2#sh nvo vxlan access-if br
Inner Admin Link
Interface Vlan vlan Ifindex Vnid status status
-----------------------------------------------------------
xe23 --- --- 500000 100 up up
Total number of entries are 1
VTEP2#sh nvo vxlan access-if-config
nvo vxlan access-if port xe23 default
map vnid 100
arp-cache disable
nd-cache disable
mac 0000.2222.0001
!
VTEP2#sh nvo vxlan arp-cache
VxLAN ARP-CACHE Information
===========================
VNID Ip-Addr Mac-Addr Type Age-Out Retries-Left
____________________________________________________________________________
Total number of entries are 0
VTEP2#sh nvo vxlan nd-cache
VxLAN ND-CACHE Information
===========================
VNID Ip-Addr Mac-Addr Type Age-Out Retries-Left
____________________________________________________________________________________________________
Total number of entries are 0
VTEP2#
VTEP2#sh bgp l2vpn evpn summary
BGP router identifier 2.2.2.2, local AS number 1
BGP table version is 2
1 BGP AS-PATH entries
0 BGP community entries
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd AD MACIP MCAST ESI PREFIX-ROUTE
1.1.1.1 4 1 27 27 1 0 0 00:09:54 3 0 2 1 0 0
Total number of neighbors 1
Total number of Established sessions 1
VTEP2#sh bgp l2vpn evpn
BGP table version is 2, local router ID is 2.2.2.2
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal,
l - labeled, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
[EVPN route type]:[ESI]:[VNID]:[relevent route informantion]
1 - Ethernet Auto-discovery Route
2 - MAC/IP Route
3 - Inclusive Multicast Route
4 - Ethernet Segment Route
5 - Prefix Route
Network Next Hop Metric LocPrf Weight Path Peer Encap
RD[1.1.1.1:1]
*>i [2]:[0]:[100]:[48,0000:1111:0001]:[0]:[100]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
*>i [2]:[0]:[100]:[48,b0da:1d10:6496]:[0]:[100]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
*>i [3]:[100]:[32,1.1.1.1]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
RD[2.2.2.2:1] VRF[L2VRF1]:
* i [2]:[0]:[100]:[48,0000:1111:0001]:[0]:[100]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
*> [2]:[0]:[100]:[48,0000:2222:0001]:[0]:[100]
2.2.2.2 0 100 32768 i ---------- VxLAN
* i [2]:[0]:[100]:[48,b0da:1d10:6496]:[0]:[100]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
* i [3]:[100]:[32,1.1.1.1]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
*> [3]:[100]:[32,2.2.2.2]
2.2.2.2 0 100 32768 i ---------- VxLAN
Total number of prefixes 8
VTEP2#
VxLAN Trunk access port with vlan range
When an access port with a specific vlan range configured, all the traffic in that specific range are accepted and forwarded.
VTEP1
(config)#nvo vxlan access-if port-vlan xe7 2-100 | Configuring the vxlan access port with vlan range 2-100 where traffic in the vlan range 2-100 are accepted |
(config-nvo-acc-if)#map vnid 100 | Map VxLAN Identified to access-port for VxLAN |
(config-nvo-acc-if)#arp-cache disable | Disable arp-cache - mandatory |
(config-nvo-acc-if)#nd-cache disable | Disable nd-cache - mandatory |
(config-nvo-acc-if)# mac 0000.1111.0001 | Configure static mac-only |
(config-nvo-acc-if)#exit | Exit from VxLAN access-interface mode and enter into configuration mode |
(config)#commit | Committing the vxlan configuration |
VTEP2
(config)#nvo vxlan access-if port-vlan xe23 2-100 | Configuring the vxlan access port with vlan range 2-100 where traffic in the vlan range 2-100 are accepted |
(config-nvo-acc-if)#map vnid 100 | Map VxLAN Identified to access-port for VxLAN |
(config-nvo-acc-if)#arp-cache disable | Disable arp-cache - mandatory |
(config-nvo-acc-if)#nd-cache disable | Disable nd-cache - mandatory |
(config-nvo-acc-if)# mac 0000.2222.0001 | Configure static mac-only |
(config-nvo-acc-if)#exit | Exit from VxLAN access-interface mode and enter into configuration mode |
(config)#commit | Committing the vxlan configuration |
Validations
VTEP1
VTEP1#sh run nvo vx
!
nvo vxlan enable
!
nvo vxlan vtep-ip-global 1.1.1.1
!
nvo vxlan id 100 ingress-replication
vxlan host-reachability-protocol evpn-bgp L2VRF1
!
nvo vxlan access-if port-vlan xe7 2-100
map vnid 100
arp-cache disable
nd-cache disable
mac 0000.1111.0001
!
!
VTEP1#
VTEP1#sh nvo vxlan tunnel summary
Total number of entries: 1 [Installed: 1, Resolved: 0, Unresolved: 0]
Total number of entries are 1
VTEP1#sh nvo vxlan tunnel
VxLAN Network tunnel Entries
Source Destination Status Up/Down Update
============================================================================
1.1.1.1 2.2.2.2 Installed 00:20:10 00:20:10
Total number of entries are 1
VTEP1#sh nvo vx
VxLAN Information
=================
Codes: NW - Network Port
AC - Access Port
(u) - Untagged
VNID VNI-Name VNI-Type Type Interface ESI VLAN DF-Status Src-Addr Dst-Addr
_______________________________________________________________________________________________________________________________
100 ---- L2 NW ---- ---- ---- ---- 1.1.1.1 2.2.2.2
100 ---- -- AC xe7 --- Single Homed Port --- 2 ---- ---- ----
Total number of entries are 2
VTEP1#sh nvo vxlan mac-table
==========================================================================================================================================
VxLAN MAC Entries
==========================================================================================================================================
VNID Interface VlanId Vlan-RangeId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status AccessPortDesc
__________________________________________________________________________________________________________________________________________
100 xe7 ----- 2-100 ---- 0000.1111.0001 1.1.1.1 Static Local ------- -------
100 ---- ---- ---- 0000.2222.0001 2.2.2.2 Static Remote ------- -------
100 xe7 ----- 2-100 ---- b0da.1d10.6496 1.1.1.1 Dynamic Local ------- -------
Total number of entries are : 3
VTEP1#sh nvo vxlan mac-table hardware
==========================================================================================================================================
VxLAN MAC Entries
==========================================================================================================================================
VNID Interface VlanId Vlan-RangeId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status Time-out AccessPortDesc
_________________________________________________________________________________________________________________________________________
100 xe7 ----- 2-100 ---- 0000.1111.0001 1.1.1.1 Static Local ------- --- -------
100 --- ---- ---- 0000.2222.0001 2.2.2.2 Remote ------- --- -------
100 xe7 ----- 2-100 ---- b0da.1d10.6496 1.1.1.1 Dynamic Local ------- 300 -------
Total number of entries are 3
VTEP1#sh nvo vxlan arp-cache
VxLAN ARP-CACHE Information
===========================
VNID Ip-Addr Mac-Addr Type Age-Out Retries-Left
____________________________________________________________________________
Total number of entries are 0
VTEP1#sh nvo vxlan nd-cache
VxLAN ND-CACHE Information
===========================
VNID Ip-Addr Mac-Addr Type Age-Out Retries-Left
____________________________________________________________________________________________________
Total number of entries are 0
VTEP1#sh nvo vxlan access-if-config
nvo vxlan access-if port-vlan xe7 2-100
map vnid 100
arp-cache disable
nd-cache disable
mac 0000.1111.0001
!
VTEP1#sh nvo vxlan access-if brief
Inner Admin Link
Interface Vlan vlan Ifindex Vnid status status
-----------------------------------------------------------
xe7 2 --- 500000 100 up up
Total number of entries are 1
VTEP1#
VTEP1#sh nvo vxlan route-count
VxLAN Active route count information
====================================
Max route count : 32768
Active route count: 3
---------------------------------------------
VNID Total MACONLY MACIPv4 MACIPv6
---------------------------------------------
100 3 3 0 0
Total number of entries are 1
VTEP1#sh bgp l2vpn evpn summary
BGP router identifier 1.1.1.1, local AS number 1
BGP table version is 5
1 BGP AS-PATH entries
0 BGP community entries
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd AD MACIP MCAST ESI PREFIX-ROUTE
2.2.2.2 4 1 58 61 5 0 0 00:22:05 2 0 1 1 0 0
Total number of neighbors 1
Total number of Established sessions 1
VTEP1#sh bgp l2vpn evpn
BGP table version is 5, local router ID is 1.1.1.1
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal,
l - labeled, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
[EVPN route type]:[ESI]:[VNID]:[relevent route informantion]
1 - Ethernet Auto-discovery Route
2 - MAC/IP Route
3 - Inclusive Multicast Route
4 - Ethernet Segment Route
5 - Prefix Route
Network Next Hop Metric LocPrf Weight Path Peer Encap
RD[1.1.1.1:1] VRF[L2VRF1]:
*> [2]:[0]:[100]:[48,0000:1111:0001]:[0]:[100]
1.1.1.1 0 100 32768 i ---------- VxLAN
* i [2]:[0]:[100]:[48,0000:2222:0001]:[0]:[100]
2.2.2.2 0 100 0 i 2.2.2.2 VxLAN
*> [2]:[0]:[100]:[48,b0da:1d10:6496]:[0]:[100]
1.1.1.1 0 100 32768 i ---------- VxLAN
*> [3]:[100]:[32,1.1.1.1]
1.1.1.1 0 100 32768 i ---------- VxLAN
* i [3]:[100]:[32,2.2.2.2]
2.2.2.2 0 100 0 i 2.2.2.2 VxLAN
RD[2.2.2.2:1]
*>i [2]:[0]:[100]:[48,0000:2222:0001]:[0]:[100]
2.2.2.2 0 100 0 i 2.2.2.2 VxLAN
*>i [3]:[100]:[32,2.2.2.2]
2.2.2.2 0 100 0 i 2.2.2.2 VxLAN
Total number of prefixes 7
VTEP2
VTEP2#sh run nvo vxlan
!
nvo vxlan enable
!
nvo vxlan vtep-ip-global 2.2.2.2
!
nvo vxlan id 100 ingress-replication
vxlan host-reachability-protocol evpn-bgp L2VRF1
!
nvo vxlan access-if port-vlan xe23 2-100
map vnid 100
arp-cache disable
nd-cache disable
mac 0000.2222.0001
!
!
VTEP2#sh nvo vxlan tunnel
VxLAN Network tunnel Entries
Source Destination Status Up/Down Update
============================================================================
2.2.2.2 1.1.1.1 Installed 00:19:28 00:19:28
Total number of entries are 1
VTEP2#sh nvo vxlan tunnel
VxLAN Network tunnel Entries
Source Destination Status Up/Down Update
============================================================================
2.2.2.2 1.1.1.1 Installed 00:21:06 00:21:06
Total number of entries are 1
VTEP2#sh nvo vxlan
VxLAN Information
=================
Codes: NW - Network Port
AC - Access Port
(u) - Untagged
VNID VNI-Name VNI-Type Type Interface ESI VLAN DF-Status Src-Addr Dst-Addr
_______________________________________________________________________________________________________________________________
100 ---- L2 NW ---- ---- ---- ---- 2.2.2.2 1.1.1.1
100 ---- -- AC xe23 --- Single Homed Port --- 2 ---- ---- ----
Total number of entries are 2
VTEP2#sh nvo vxlan mac-table
==========================================================================================================================================
VxLAN MAC Entries
==========================================================================================================================================
VNID Interface VlanId Vlan-RangeId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status AccessPortDesc
__________________________________________________________________________________________________________________________________________
100 ---- ---- ---- 0000.1111.0001 1.1.1.1 Static Remote ------- -------
100 xe23 ----- 2-100 ---- 0000.2222.0001 2.2.2.2 Static Local ------- -------
100 ---- ---- ---- b0da.1d10.6496 1.1.1.1 Dynamic Remote ------- -------
Total number of entries are : 3
VTEP2#sh nvo vxlan mac-table hardware
==========================================================================================================================================
VxLAN MAC Entries
==========================================================================================================================================
VNID Interface VlanId Vlan-RangeId Inner-VlanId Mac-Addr VTEP-Ip/ESI Type Status Time-out AccessPortDesc
_________________________________________________________________________________________________________________________________________
100 --- ---- ---- 0000.1111.0001 1.1.1.1 Remote ------- --- -------
100 xe23 ----- 2-100 ---- 0000.2222.0001 2.2.2.2 Static Local ------- --- -------
100 --- ---- ---- b0da.1d10.6496 1.1.1.1 Remote ------- --- -------
Total number of entries are 3
VTEP2#sh nvo vxlan route-count
VxLAN Active route count information
====================================
Max route count : 32768
Active route count: 3
---------------------------------------------
VNID Total MACONLY MACIPv4 MACIPv6
---------------------------------------------
100 3 3 0 0
Total number of entries are 1
VTEP2#sh nvo vxlan arp-cache
VxLAN ARP-CACHE Information
===========================
VNID Ip-Addr Mac-Addr Type Age-Out Retries-Left
____________________________________________________________________________
Total number of entries are 0
VTEP2#sh nvo vxlan nd-cache
VxLAN ND-CACHE Information
===========================
VNID Ip-Addr Mac-Addr Type Age-Out Retries-Left
____________________________________________________________________________________________________
Total number of entries are 0
VTEP2#
VTEP2#
VTEP2#sh nvo vxlan access-if brief
Inner Admin Link
Interface Vlan vlan Ifindex Vnid status status
-----------------------------------------------------------
xe23 2 --- 500000 100 up up
Total number of entries are 1
VTEP2#sh nvo vxlan access-if-config
nvo vxlan access-if port-vlan xe23 2-100
map vnid 100
arp-cache disable
nd-cache disable
mac 0000.2222.0001
!
VTEP2#sh bgp l2vpn evpn summary
BGP router identifier 2.2.2.2, local AS number 1
BGP table version is 4
1 BGP AS-PATH entries
0 BGP community entries
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd AD MACIP MCAST ESI PREFIX-ROUTE
1.1.1.1 4 1 59 57 3 0 0 00:21:48 3 0 2 1 0 0
Total number of neighbors 1
Total number of Established sessions 1
VTEP2#sh bgp l2vpn evpn
BGP table version is 4, local router ID is 2.2.2.2
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal,
l - labeled, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
[EVPN route type]:[ESI]:[VNID]:[relevent route informantion]
1 - Ethernet Auto-discovery Route
2 - MAC/IP Route
3 - Inclusive Multicast Route
4 - Ethernet Segment Route
5 - Prefix Route
Network Next Hop Metric LocPrf Weight Path Peer Encap
RD[1.1.1.1:1]
*>i [2]:[0]:[100]:[48,0000:1111:0001]:[0]:[100]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
*>i [2]:[0]:[100]:[48,b0da:1d10:6496]:[0]:[100]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
*>i [3]:[100]:[32,1.1.1.1]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
RD[2.2.2.2:1] VRF[L2VRF1]:
* i [2]:[0]:[100]:[48,0000:1111:0001]:[0]:[100]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
*> [2]:[0]:[100]:[48,0000:2222:0001]:[0]:[100]
2.2.2.2 0 100 32768 i ---------- VxLAN
* i [2]:[0]:[100]:[48,b0da:1d10:6496]:[0]:[100]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
* i [3]:[100]:[32,1.1.1.1]
1.1.1.1 0 100 0 i 1.1.1.1 VxLAN
*> [3]:[100]:[32,2.2.2.2]
2.2.2.2 0 100 32768 i ---------- VxLAN
Total number of prefixes 8
VTEP2#