MPLS Statistics Configuration

OcNOS SP : Multi-Protocol Label Switching Guide : Multi-Protocol Label Switching Configuration : MPLS Statistics Configuration

This chapter provides the configuration required for configuring MPLS LSPs and verifying the statistics of packets captured at the supported interfaces, in terms of both packet count and bytes, when traffic is sent.

Configure LDP-LSP

Topology

MPLS Statistics Topology

RTR1: Loopback Interface configuration

#configure terminal	Enter configure mode.
(config)#interface lo	Specify the interface (lo) to be configured.
(config-if)#ip address 11.11.11.11/32 secondary	Configure IP address on loopback interface
(config-if)#commit	Commit the transaction.

RTR1: Global LDP configuration

(config)#router ldp	Enter Router mode for LDP.
(config-router)#router-id 11.11.11.11	Configure the router-id
(config-router)#transport-address ipv4 11.11.11.11	Configure the loopback address as transport-address
(config-router)#targeted-peer ipv4 44.44.44.44	Configure the loopback address of RTR4 as targeted peer.
(config-router-targeted-peer)#exit	Exit router-targeted-peer mode and enter config-router mode
(config-router-targeted-peer)#commit	Commit the transaction.

RTR1: Enabling LDP and label switching on interface

(config)#interface xe2	Enter interface mode for xe2.
(config-if)#enable-ldp ipv4	Enable LDP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#ip address 10.10.10.1/24	Configure IP address on the interface.
(config-if)#commit	Commit the transaction.

RTR1: Global OSPF configuration

(config)#router ospf 100	Enter the Router OSPF mode.
(config-router)#network 11.11.11.11/32 area 0	Advertise loopback address in OSPF.
(config-router)#network 10.10.10.0/24 area 0	Advertise network address (xe2) in OSPF.
(config-router)#commit	Commit the transaction.

RTR2: Loopback Interface configuration

#configure terminal	Enter configure mode.
(config)#interface lo	Specify the interface (lo) to be configured.
(config-if)#ip address 22.22.22.22/32 secondary	Configure IP address on loopback interface
(config-if)#commit	Commit the transaction.

RTR2: Global LDP configuration

(config)#router ldp	Enter Router mode for LDP.
(config-router)#router-id 22.22.22.22	Configure the router-id
(config-router)#transport-address ipv4 22.22.22.22	Configure the loopback address as transport-address
(config-router)#commit	Commit the transaction.

RTR2: Enabling LDP and label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#enable-ldp ipv4	Enable LDP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#ip address 10.10.10.2/24	Configure IP address on the interface.
(config-if)#exit	Exit interface mode.
(config)#interface xe2	Enter interface mode for xe2.
(config-if)#enable-ldp ipv4	Enable LDP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#ip address 20.20.20.1/24	Configure IP address on the interface.
(config-if)#commit	Commit the transaction.

RTR2: OSPF Configuration

(config)#router ospf 100	Enter the Router OSPF mode
(config-router)#network 22.22.22.22/32 area 0.0.0.0	Advertise loopback address in OSPF
(config-router)#network 10.10.10.2/24 area 0.0.0.0	Advertise network address (xe1) in OSPF.
(config-router)#network 20.20.20.1/24 area 0.0.0.0	Advertise network address (xe2) in OSPF.
(config-router)#commit	Commit the transaction.

RTR3: Loopback Interface configuration

#configure terminal	Enter configure mode.
(config)#interface lo	Specify the interface (lo) to be configured.
(config-if)#ip address 33.33.33.33/32 secondary	Configure IP address on loopback interface
(config-if)#commit	Commit the transaction.

RTR3: Global LDP configuration

(config)#router ldp	Enter Router mode for LDP.
(config-router)#router-id 33.33.33.33	Configure the router-id
(config-router)#transport-address ipv4 33.33.33.33	Configure the loopback address as transport-address
(config-router)#commit	Commit the transaction.

RTR3: Enabling LDP and label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#enable-ldp ipv4	Enable LDP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#ip address 20.20.20.2/24	Configure IP address on the interface.
(config-if)#exit	Exit interface mode.
(config)#interface xe2	Enter interface mode for xe2.
(config-if)#enable-ldp ipv4	Enable LDP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#ip address 30.30.30.1/24	Configure IP address on the interface.
(config-if)#commit	Commit the transaction.

RTR3: OSPF Configuration

(config)#router ospf 100	Enter the Router OSPF mode
(config-router)#network 33.33.33.33/32 area 0.0.0.0	Advertise loopback address in OSPF
(config-router)#network 20.20.20.2/24 area 0.0.0.0	Advertise network address (xe1) in OSPF.
(config-router)#network 30.30.30.1/24 area 0.0.0.0	Advertise network address (xe2) in OSPF.
(config-router)#commit	Commit the transaction.

RTR4: Loopback Interface configuration

#configure terminal	Enter configure mode.
(config)#interface lo	Specify the interface (lo) to be configured.
(config-if)#ip address 44.44.44.44/32 secondary	Configure IP address on loopback interface
(config-if)#commit	Commit the transaction.

RTR4: Global LDP configuration

(config)#router ldp	Enter Router mode for LDP.
(config-router)#router-id 44.44.44.44	Configure the router-id
(config-router)#transport-address ipv4 44.44.44.44	Configure the loopback address as transport-address
(config-router)#targeted-peer ipv4 11.11.11.11	Configure the loopback address of RTR1 as targeted peer.
(config-router-targeted-peer)#exit	Exit router-targeted-peer mode and enter config-router mode
(config-router)#commit	Commit the transaction.

RTR4: Enabling LDP and label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#enable-ldp ipv4	Enable LDP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#ip address 30.30.30.2/24	Configure IP address on the interface.
(config-if)#commit	Commit the transaction.

RTR4: Global OSPF Configuration

(config)#router ospf 100	Enter the Router OSPF mode
(config-router)#network 44.44.44.44/32 area 0.0.0.0	Advertise loopback address in OSPF
(config-router)#network 30.30.30.2/24 area 0.0.0.0	Advertise network address (xe1) in OSPF.
(config-router)#commit	Commit the transaction.

MPLS LDP VPLS Configuration

RTR1: VPLS

(config)#mpls vpls vpls1 1	Enter the VPLS configuration mode
(config-vpls)# signaling ldp	Use LDP signaling for VPLS
(config-vpls-sig)#vpls-type ethernet	Configure the VPLS as Ethernet
(config-vpls-sig)#vpls-peer 44.44.44.44	Configure RTR4 as VPLS peer for RTR1.
(config-vpls-sig)#exit-signaling	Exit signaling mode
(config-vpls)# exit-vpls	Exit VPLS config mode and return to Configure mode
(config-vpls)#commit	Commit the transaction.

RTR1: Interface

(config)#service-template st1	Template configuration
(config-svc)#exit	Exit service template mode
(config)#interface xe1	Enter the Interface mode for xe1
(config-if)#switchport	Enable switchport on the interface
(config-if)#mpls-vpls vpls1 service-template st1	Bind the VPLS to the Access Interface.
(config-if-vpls)#split-horizon group access1	Configure split-horizon group on VPLS
(config-if)#commit	Commit the transaction.

RTR4: VPLS

(config)#mpls vpls vpls1 1	Enter the VPLS configuration mode
(config-vpls)#signaling ldp	Use LDP signaling for VPLS
(config-vpls-sig)#vpls-type ethernet	Configure the VPLS as Ethernet
(config-vpls-sig)#vpls-peer 11.11.11.11	Configure RTR1 as VPLS peer for RTR4.
(config-vpls-sig)#exit-signaling	Exit signaling mode
(config-vpls)#commit	Commit the transaction.

RTR4: Interface

(config)#service-template st1	Template configuration
(config-svc)#exit	Exit service template mode
(config)#interface xe2	Enter the Interface mode for xe2
(config-if)#switchport	Enable switchport on the interface
(config-if)#mpls-vpls vpls1 service template st1	Bind the VPLS to the Access Interface.
(config-if-vpls)#split-horizon group access1	Configure split-horizon group on VPLS
(config-if-vpls)#commit	Commit the transaction.

Virtual Circuit Configuration

RTR1: Global VC Configuration

(config)#mpls l2-circuit t1 100 44.44.44.44	Enter the VC configuration command in router mode.
(config-pseudowire)#exit	Exit service template mode
(config)#bridge 1 protocol ieee vlan-bridge	Creating a VLAN-bridge in router mode.
(config)#commit	Commit the transaction.

RTR1: Interface Configuration

(config)#service-template st1	Template configuration
(config-svc)#exit	Exit service template configuration
(config)#interface xe1	Enter interface mode for xe1.
(config-if)#switchport	Enable switchport on the interface.
(config-if)#mpls-vpls vpls1 service-template st1	Bind the interface to VPLS.
(config-if-vpls)#split-horizon group access1	Configure split-horizon group on VPLS
(config-if)#commit	Commit the transaction.

RTR4: Global VC Configuration

(config)#mpls l2-circuit t1 100 11.11.11.11	Enter the VC configuration command in router mode.
(config)#exit	Exit service template mode.
(config)#bridge 1 protocol ieee vlan-bridge	Creating a VLAN-bridge in router mode.
(config)#commit	Commit the transaction.

RTR4: Interface Configuration

(config)#service-template st1	Template configuration
(config-svc)#exit	Exit service template mode
(config)#interface xe2	Enter interface mode for xe2.
(config-if)#switchport	Enable switchport on the interface.
(config-if)#mpls-vpls vpls1 service-template st1	Bind the interface to VPLS.
(config-if-vpls)#split-horizon group access1	Configure split-horizon group on VPLS
(config)#commit	Commit the transaction.

VPLS Configuration

RTR1: Global VPLS Configuration

(config)#mpls vpls vpls1 1	Enter the VPLS configuration mode.
(config-vpls)#signaling ldp	Use LDP signaling for VPLS.
(config-vpls-sig)#vpls-peer 44.44.44.44	Configure RTR4 as VPLS peer for RTR1.
(config-vpls-sig)#exit-signaling	Exit signaling mode.
(config-vpls)#commit	Commit the transaction.

RTR1: Interface Configuration

(config)#service-template st1	Template configuration
(config-svc)#exit	Exit service template mode
(config)#interface xe1	Enter interface mode for xe1.
(config-if)#switchport	Enable switchport on the interface.
(config-if)#mpls-vpls vpls1 service-template st1	Bind the interface to VPLS.
(config-if-vpls)#commit	Commit the transaction.

RTR4: Global VC Configuration

(config)#mpls vpls vpls1 1	Enter the VPLS configuration mode.
(config-vpls)#signaling ldp	Use LDP signaling for VPLS.
(config-vpls-sig)#vpls-peer 11.11.11.11	Configure RTR4 as VPLS peer for RTR1.
(config-vpls-sig)#exit-signaling	Exit signaling mode.
(config-vpls)#commit	Commit the transaction.

RTR4: Interface Configuration

(config)#service-template st1	Template configuration
(config-svc)#exit	Exit service template mode
(config)#interface xe2	Enter interface mode for xe2.
(config-if)#switchport	Enable switchport on the interface.
(config-if)#mpls-vpls vpls1 service-template st1	Bind the interface to VPLS.
(config-if-vpls)#exit	Exit VPLS mode and return to interface mode.
(config-if)#commit	Commit the transaction.

Configure RSVP-LSP

RTR1: Global RSVP configuration

#configure terminal	Enter configure mode.
(config)#router rsvp	Enter RSVP configuration mode for the router.
(config-router)#commit	Commit the transaction.

RTR1: Enabling RSVP and label switching on interface

(config)#interface xe2	Enter interface mode for xe2.
(config-if)#enable-rsvp	Enable RSVP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#commit	Commit the transaction.

RTR1: Trunk Configuration

(config)#rsvp-trunk t1	Configure RSVP trunk t1
(config-trunk)#to 44.44.44.44	Configure RTR4 as the end of trunk
(config-trunk)#commit	Commit the transaction.

RTR2: Global RSVP configuration

(config)#router rsvp	Enter RSVP configuration mode for the router.
(config-router)#php	Configure PHP on the end node.
(config-router)#commit	Commit the transaction.

RTR2: Enabling RSVP and label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#enable-rsvp	Enable RSVP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#exit	Exit interface mode.
(config)#interface xe2	Enter interface mode for xe2.
(config-if)#enable-rsvp	Enable RSVP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#commit	Commit the transaction.

RTR3: Global RSVP configuration

#configure terminal	Enter configure mode.
(config)#router rsvp	Enter RSVP configuration mode for the router.
(config-router)#php	Configure PHP on the end node.
(config-router)#commit	Commit the transaction.

RTR3: Enabling RSVP and label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#enable-rsvp	Enable RSVP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#exit	Exit interface mode.
(config)#interface xe3	Enter interface mode for xe3.
(config-if)#enable-rsvp	Enable RSVP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#commit	Commit the transaction.

RTR4: Global RSVP configuration

#configure terminal	Enter configure mode.
(config)#router rsvp	Enter RSVP configuration mode for the router.
(config-router)#commit	Commit the transaction.

RTR4: Enabling RSVP and label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#enable-rsvp	Enable RSVP on the interface.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#commit	Commit the transaction.

RTR4: Trunk Configuration

(config)#rsvp-trunk t2	Configure RSVP trunk t2.
(config-trunk)#to 11.11.11.11	Configure RTR1 as the end of trunk.
(config-trunk)#commit	Commit the transaction.

Configure Static-LSP

RTR1: Global Static configuration

(config)#mpls ftn-entry 44.44.44.44/32 100 10.10.10.2 xe1	Configure FTN entry for rtr4 loopback.
(config)#mpls ilm-entry 900 pop	Pop the incoming label
(config)#commit	Commit the transaction.

RTR1: Enabling label switching on interface

(config)#interface xe2	Enter interface mode for xe2.
(config-if)#label-switching	Enable Label switching on the interface.
(config)#commit	Commit the transaction.

RTR2: Global Static configuration

mpls ilm-entry 100 swap 200 xe2 20.20.20.2 44.44.44.44/32	Swap the incoming label
mpls ilm-entry 800 swap 900 xe1 10.10.10.1 11.11.11.11/32	Swap the incoming label

RTR2: Enabling label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#exit	Exit interface mode.
(config)#interface xe2	Enter interface mode for xe2.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#commit	Commit the transaction.

RTR3: Global Static configuration

(config)#mpls ilm-entry 200 swap 300 xe2 30.30.30.2 44.44.44.44/32	Swap the incoming label
(config)#mpls ilm-entry 700 swap 800 xe1 20.20.20.1 11.11.11.11/32	Swap the incoming label
(config)#commit	Commit the transaction.

RTR3: Enabling label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#exit	Exit interface mode.
(config)#interface xe3	Enter interface mode for xe3.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#commit	Commit the transaction.

RTR4: Global Static configuration

(config)#mpls ftn-entry 11.11.11.11/32 700 30.30.30.1 xe1	Configure FTN entry for RTR1 loopback.
(config)mpls ilm-entry 300 pop	Pop the incoming label.
(config)#commit	Commit the transaction.

RTR4: Enabling label switching on interface

(config)#interface xe1	Enter interface mode for xe1.
(config-if)#label-switching	Enable Label switching on the interface.
(config-if)#commit	Commit the transaction.

Validation

Here, 1000 packets are transmitted between the PE nodes and the output of counters at each node is mentioned below.

For Static-LSP

RTR1#show mpls counters static

[FTN statistics]

+------------------+-----------+--------------------+--------------------+

+------------------+-----------+--------------------+--------------------+

44.44.44.44/32 100 49939 807798

[ILM statistics]

+------------------+-----------+-----------+--------------------+--------------------+--------------------+--------------------+

+------------------+-----------+-----------+--------------------+--------------------+--------------------+--------------------+

0.0.0.0/0 900 n/a 40546 3486956 n/a n/a

RTR1#

RTR2#show mpls counters static

[FTN statistics]

+------------------+-----------+--------------------+--------------------+

+------------------+-----------+--------------------+--------------------+

[ILM statistics]

+------------------+-----------+-----------+--------------------+---------------

-----+--------------------+--------------------+

| Tx packets | Tx bytes |

+------------------+-----------+-----------+--------------------+---------------

-----+--------------------+--------------------+

44.44.44.44/32 100 200 9393 807798

9393 807798

11.11.11.11/32 800 900 40546 3486956

40546 3486956

RTR2#

RTR3#show mpls counters static

[FTN statistics]

+------------------+-----------+--------------------+--------------------+

+------------------+-----------+--------------------+--------------------+

[ILM statistics]

+------------------+-----------+-----------+--------------------+--------------------+--------------------+--------------------+

+------------------+-----------+-----------+--------------------+--------------------+--------------------+--------------------+

44.44.44.44/32 200 300 9393 807798 9393 807798

11.11.11.11/32 700 800 40546 3486956 40546 3486956

RTR3#

RTR4#show mpls counters static

[FTN statistics]

+------------------+-----------+--------------------+--------------------+

+------------------+-----------+--------------------+--------------------+

11.11.11.11/32 700 49939 3486956

[ILM statistics]

+------------------+-----------+-----------+--------------------+---------------

-----+--------------------+--------------------+

| Tx packets | Tx bytes |

+------------------+-----------+-----------+--------------------+---------------

-----+--------------------+--------------------+

0.0.0.0/0 300 n/a 9393 807798

n/a n/a

RTR4#

For RSVP-LSP

RTR1#show mpls counters rsvp

Tunnel-id 5001 Extended Tunnel-ID 44.44.44.44 Egress 11.11.11.11

lsp-name : t1-Primary [Egress]

lsp-ingress : 44.44.44.44 lsp-id : 2201

Rx pkts : 2509072 Rx bytes : 187780192

Tx pkts : 0 Tx bytes : 0

Tunnel-id 5001 Extended Tunnel-ID 11.11.11.11 Egress 44.44.44.44

lsp-name : t1-Primary [Ingress]

lsp-ingress : 11.11.11.11 lsp-id : 2201

Rx pkts : 0 Rx bytes : 0

Tx pkts : 5578405 Tx bytes : 451417492

RTR2#show mpls counters rsvp

Tunnel-id 5001 Extended Tunnel-ID 44.44.44.44 Egress 11.11.11.11

lsp-name : t1-Primary [Transit]

lsp-ingress : 44.44.44.44 lsp-id : 2201

Rx pkts : 2565947 Rx bytes : 192671442

Tx pkts : 2565960 Tx bytes : 192672560

Tunnel-id 5001 Extended Tunnel-ID 11.11.11.11 Egress 44.44.44.44

lsp-name : t1-Primary [Transit]

lsp-ingress : 11.11.11.11 lsp-id : 2201

Rx pkts : 5631460 Rx bytes : 456305560

Tx pkts : 5631472 Tx bytes : 456306592

RTR3#show mpls counters rsvp

Tunnel-id 5001 Extended Tunnel-ID 44.44.44.44 Egress 11.11.11.11

lsp-name : t1-Primary [Transit]

lsp-ingress : 44.44.44.44 lsp-id : 2201

Rx pkts : 2565947 Rx bytes : 282671442

Tx pkts : 2565960 Tx bytes : 282672560

Tunnel-id 5001 Extended Tunnel-ID 11.11.11.11 Egress 44.44.44.44

lsp-name : t1-Primary [Transit]

lsp-ingress : 11.11.11.11 lsp-id : 2201

Rx pkts : 8631460 Rx bytes : 457245560

Tx pkts : 8631472 Tx bytes : 45724592

RTR4#show mpls counters rsvp

Tunnel-id 5001 Extended Tunnel-ID 44.44.44.44 Egress 11.11.11.11

lsp-name : t1-Primary [Ingress]

lsp-ingress : 44.44.44.44 lsp-id : 2201

Rx pkts : 0 Rx bytes : 0

Tx pkts : 10231330 Tx bytes : 374371318

Tunnel-id 5001 Extended Tunnel-ID 11.11.11.11 Egress 44.44.44.44

lsp-name : t1-Primary [Egress]

lsp-ingress : 11.11.11.11 lsp-id : 2201

Rx pkts : 5651207 Rx bytes : 458003802

Tx pkts : 0 Tx bytes : 0

R3#show mpls counters rsvp

Tunnel-id 5001 Extended Tunnel-ID 44.44.44.44 Egress 11.11.11.11 lsp-name : t1-Primary [Transit]

lsp-ingress : 44.44.44.44 lsp-id : 2201

Rx pkts : 2565947 Rx bytes : 282671442

Tx pkts : 2565960 Tx bytes : 282672560

Tunnel-id 5001 Extended Tunnel-ID 11.11.11.11 Egress 44.44.44.44 lsp-name : t1-Primary [Transit]

lsp-ingress : 11.11.11.11 lsp-id : 2201

Rx pkts : 8631460 Rx bytes : 457245560

Tx pkts : 8631472 Tx bytes : 45724592

R4#show mpls counters rsvp

Tunnel-id 5001 Extended Tunnel-ID 44.44.44.44 Egress 11.11.11.11 lsp-name : t1-Primary [Ingress]

lsp-ingress : 44.44.44.44 lsp-id : 2201 Rx pkts : 0 Rx bytes : 0

Tx pkts : 10231330 Tx bytes : 374371318

Tunnel-id 5001 Extended Tunnel-ID 11.11.11.11 Egress 44.44.44.44 lsp-name : t1-Primary [Egress]

lsp-ingress : 11.11.11.11 lsp-id : 2201

Rx pkts : 5651207 Rx bytes : 458003802

Tx pkts : 0 Tx bytes : 0

For LDP-LSP

RTR1#show mpls counters ldp

[FTN statistics]

+------------------+-----------+--------------------+--------------------+

+------------------+-------------+------------------+--------------------+

44.44.44.44/32 52483 1000 1004000

[ILM statistics]

+-----+---------+-----------+------------+---------+-----------+---------+

+-----+---------+-----------+------------+---------+-----------+---------+

RTR2#show mpls counters ldp

[FTN statistics]

+------------------+-----------+--------------------+--------------------+

+------------------+-----------+--------------------+--------------------+

[ILM statistics]

+-----+----------+-----------+------------+----------+------------+----------+

+-----+----------+-----------+------------+----------+------------+----------+

44.44.44.44/32 52483 52483 1000 1004000 1000 1004000

/RTR2#show mpls counters ldp [FTN statistics]

+------------------+-----------+--------------------+--------------------+

+------------------+-----------+--------------------+--------------------+

[ILM statistics]

+-----+----------+-----------+------------+----------+------------+----------+

+-----+----------+-----------+------------+----------+------------+----------+ 44.44.44.44/32 52483 52483 1000 1004000 1000 1004000

For LDP-VC

RTR1#show mpls l2-circuit t1 statistics

MPLS Layer-2 Virtual Circuit: t1, id 100

Access port statistics:

RX: Input packets : 0

Input bytes : 0

TX: Output packets : 4642811

Output bytes : 297139904

Network port statistics:

RX: Input packets : 4642804

Input bytes : 399281144

TX: Output packets : 0

Output bytes : 0

RTR4#show mpls l2-circuit t1 statistics

MPLS Layer-2 Virtual Circuit: t1, id 100

Access port statistics:

RX: Input packets : 4633957

Input bytes : 296573248

TX: Output packets : 0

Output bytes : 0

Network port statistics:

RX: Input packets : 0

Input bytes : 0

TX: Output packets : 4633960

Output bytes : 398520560

For LDP-VPLS

RTR1#show mpls vpls vpls1 statistics

Virtual Private LAN Service Instance: vpls1, ID: 1

Access port statistics:

Interface: xe1

RX: Input packets : 1922483

Input bytes : 123038912

TX: Output packets : 3894242

Output bytes : 126192000

Network port statistics:

Mesh Peer: 44.44.44.44 (Up)

RX: Input packets : 1971746

Input bytes : 169570156

TX: Output packets : 3894244

Output bytes : 165334398

RTR4#show mpls vpls vpls1 statistics

Virtual Private LAN Service Instance: vpls1, ID: 1

Access port statistics:

Interface: xe2

RX: Input packets : 1967571

Input bytes : 125924544

TX: Output packets : 3885889

Output bytes : 122772032

Network port statistics:

Mesh Peer: 11.11.11.11 (Up)

RX: Input packets : 1918310

Input bytes : 164974660

TX: Output packets : 3885892

Output bytes : 169211622