IPI-ACL-IPV6
Configure vlan id
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: union
Attribute Name: destination-address
Attribute Type: union
Attribute Name: dscp
Attribute Type: union
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any|X:X::X:X/M|X:X::X:X X:X::X:X) (any|X:X::X:X/M|X:X::X:X X:X::X:X) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7|<0-63>)|) (vlan <1-4094>|)
Configure name
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: destination-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: tcp-destination-port
Attribute Type: union
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<destination-port-operator>eq</destination-port-operator> <!-- operation="delete"-->
<tcp-destination-port>echo</tcp-destination-port> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any) (any) (eq|neq|lt|gt) (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip|<0-65535>) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure type
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: lower-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<lower-destination-port-in-range>0</lower-destination-port-in-range> <!-- operation="delete"-->
<upper-destination-port-in-range>0</upper-destination-port-in-range> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any) (any) range <0-65535> <0-65535> (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure sequence id
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: source-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: tcp-source-port
Attribute Type: union
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: destination-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: tcp-destination-port
Attribute Type: enum (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<source-port-operator>eq</source-port-operator> <!-- operation="delete"-->
<tcp-source-port>echo</tcp-source-port> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<destination-port-operator>eq</destination-port-operator> <!-- operation="delete"-->
<tcp-destination-port>echo</tcp-destination-port> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any) (eq|neq|lt|gt) (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip|<0-65535>) (any) (eq|neq|lt|gt) (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure forwarding action
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: source-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: tcp-source-port
Attribute Type: enum (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: lower-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<source-port-operator>eq</source-port-operator> <!-- operation="delete"-->
<tcp-source-port>echo</tcp-source-port> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<lower-destination-port-in-range>0</lower-destination-port-in-range> <!-- operation="delete"-->
<upper-destination-port-in-range>0</upper-destination-port-in-range> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any) (eq|neq|lt|gt) (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip) (any) range <0-65535> <0-65535> (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure protocol tcp
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: source-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: tcp-source-port
Attribute Type: enum (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<source-port-operator>eq</source-port-operator> <!-- operation="delete"-->
<tcp-source-port>echo</tcp-source-port> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any) (eq|neq|lt|gt) (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip) (any) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure source address
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: lower-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: destination-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: tcp-destination-port
Attribute Type: enum (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<lower-source-port-in-range>0</lower-source-port-in-range> <!-- operation="delete"-->
<upper-source-port-in-range>0</upper-source-port-in-range> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<destination-port-operator>eq</destination-port-operator> <!-- operation="delete"-->
<tcp-destination-port>echo</tcp-destination-port> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any) range <0-65535> <0-65535> (any) (eq|neq|lt|gt) (echo|discard|daytime|chargen|ftp-data|ftp|ssh|telnet|smtp|time|whois|tacacs|domain|gopher|finger|www|hostname|pop2|pop3|sunrpc|ident|nntp|bgp|irc|pim-auto-rp|exec|login|cmd|lpd|talk|uucp|klogin|kshell|drip) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure lower source port in range
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: lower-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: lower-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<lower-source-port-in-range>0</lower-source-port-in-range> <!-- operation="delete"-->
<upper-source-port-in-range>0</upper-source-port-in-range> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<lower-destination-port-in-range>0</lower-destination-port-in-range> <!-- operation="delete"-->
<upper-destination-port-in-range>0</upper-destination-port-in-range> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any) range <0-65535> <0-65535> (any) range <0-65535> <0-65535> (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure upper source port in range
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-tcp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: lower-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-tcp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<lower-source-port-in-range>0</lower-source-port-in-range> <!-- operation="delete"-->
<upper-source-port-in-range>0</upper-source-port-in-range> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) tcp (any) range <0-65535> <0-65535> (any) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure protocol udp
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-udp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-udp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) udp (any) (any) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure destination address
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-udp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: destination-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: udp-destination-port
Attribute Type: union
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-udp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<destination-port-operator>eq</destination-port-operator> <!-- operation="delete"-->
<udp-destination-port>echo</udp-destination-port> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) udp (any) (any) (eq|neq|lt|gt) (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp|<0-65535>) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure lower destination port in range
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-udp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: lower-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-udp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<lower-destination-port-in-range>0</lower-destination-port-in-range> <!-- operation="delete"-->
<upper-destination-port-in-range>0</upper-destination-port-in-range> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) udp (any) (any) range <0-65535> <0-65535> (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure source port operator
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-udp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: source-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: udp-source-port
Attribute Type: union
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: destination-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: udp-destination-port
Attribute Type: enum (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-udp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<source-port-operator>eq</source-port-operator> <!-- operation="delete"-->
<udp-source-port>echo</udp-source-port> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<destination-port-operator>eq</destination-port-operator> <!-- operation="delete"-->
<udp-destination-port>echo</udp-destination-port> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) udp (any) (eq|neq|lt|gt) (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp|<0-65535>) (any) (eq|neq|lt|gt) (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure udp source port
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-udp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: source-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: udp-source-port
Attribute Type: enum (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: lower-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-udp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<source-port-operator>eq</source-port-operator> <!-- operation="delete"-->
<udp-source-port>echo</udp-source-port> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<lower-destination-port-in-range>0</lower-destination-port-in-range> <!-- operation="delete"-->
<upper-destination-port-in-range>0</upper-destination-port-in-range> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) udp (any) (eq|neq|lt|gt) (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp) (any) range <0-65535> <0-65535> (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure dscp
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-udp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: source-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: udp-source-port
Attribute Type: enum (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-udp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<source-port-operator>eq</source-port-operator> <!-- operation="delete"-->
<udp-source-port>echo</udp-source-port> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) udp (any) (eq|neq|lt|gt) (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp) (any) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure destination port operator
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-udp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: lower-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: destination-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: udp-destination-port
Attribute Type: enum (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-udp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<lower-source-port-in-range>0</lower-source-port-in-range> <!-- operation="delete"-->
<upper-source-port-in-range>0</upper-source-port-in-range> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<destination-port-operator>eq</destination-port-operator> <!-- operation="delete"-->
<udp-destination-port>echo</udp-destination-port> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) udp (any) range <0-65535> <0-65535> (any) (eq|neq|lt|gt) (echo|discard|time|nameserver|tacacs|domain|bootps|bootpc|tftp|sunrpc|ntp|netbios-ns|netbios-dgm|netbios-ss|snmp|snmptrap|xdmcp|dnsix|mobile-ip|pim-auto-rp|isakmp|biff|who|syslog|talk|rip|non500-isakmp) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure upper destination port in range
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-udp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: lower-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-source-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: lower-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: upper-destination-port-in-range
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-udp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<lower-source-port-in-range>0</lower-source-port-in-range> <!-- operation="delete"-->
<upper-source-port-in-range>0</upper-source-port-in-range> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<lower-destination-port-in-range>0</lower-destination-port-in-range> <!-- operation="delete"-->
<upper-destination-port-in-range>0</upper-destination-port-in-range> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) udp (any) range <0-65535> <0-65535> (any) range <0-65535> <0-65535> (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure protocol icmp
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-icmp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-icmp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) icmpv6 (any) (any) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure protocol sctp
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-sctp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-sctp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) sctp (any) (any) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure sctp destination port
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-sctp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: destination-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: sctp-destination-port
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-sctp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<destination-port-operator>eq</destination-port-operator> <!-- operation="delete"-->
<sctp-destination-port>0</sctp-destination-port> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) sctp (any) (any) (eq|neq|lt|gt) <0-65535> (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure sctp source port
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-sctp
Attribute Type: empty
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: source-port-operator
Attribute Type: enum (eq|neq|lt|gt)
Attribute Name: sctp-source-port
Attribute Type: uint16
Attribute Range: 0-65535
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
</protocol-sctp><!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<source-port-operator>eq</source-port-operator> <!-- operation="delete"-->
<sctp-source-port>0</sctp-source-port> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) sctp (any) (eq|neq|lt|gt) <0-65535> (any) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)
Configure protocol name
Use this attribute to set the vlan-id
This command is supported when following feature are enabled IPV6 feature
Attribute Name: vlan-id
Attribute Type: uint16
Attribute Range: 1-4094
Attribute Name: forwarding-action
Attribute Type: enum (deny|permit)
Attribute Name: protocol-name
Attribute Type: union
Attribute Name: source-address
Attribute Type: enum (any)
Attribute Name: destination-address
Attribute Type: enum (any)
Attribute Name: dscp
Attribute Type: enum (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)
Netconf edit-config payload
<acl xmlns="http://www.ipinfusion.com/yang/ocnos/ipi-acl">
<name>NAME</name>
<config>
<name>WORD</name>
<type>mac</type>
</config>
<type>mac</type>
<sequence-id>1</sequence-id>
<config>
<sequence-id>1</sequence-id>
</config>
<ipv6>
<config>
<forwarding-action>deny</forwarding-action> <!-- operation="delete"-->
<protocol-name>ipipv6</protocol-name> <!-- operation="delete"-->
<source-address>any</source-address> <!-- operation="delete"-->
<destination-address>any</destination-address> <!-- operation="delete"-->
<dscp>default</dscp> <!-- operation="delete"-->
<vlan-id>1</vlan-id> <!-- operation="delete"-->
</config>
</ipv6>
</acl-entry>
</acl-entries>
</acl-set>
</acl-sets>
</acl>
Command Syntax
(<1-268435453>|) (deny|permit) (ipipv6|ipv6ipv6|rsvp|gre|esp|ahp|ospf|pim|ipcomp|vrrp|any|<0-255>) (any) (any) (dscp (default|cs1|af11|af12|af13|cs2|af21|af22|af23|cs3|af31|af32|af33|cs4|af41|af42|af43|cs5|ef|cs6|cs7)|) (vlan <1-4094>|)