SW1#configure terminal | Enter configure mode. |
SW1(config)# bridge 1 protocol mstp | Configure bridge 1 as MSTP bridge |
SW1(config)# vlan database | Enter VLAN database mode. |
SW1(config-vlan)# vlan 2-10 bridge 1 state enable | Configure a VLAN and add it to the bridge. |
SW1(config-vlan)# commit | Commit the candidate configuration to the running Configuration. |
SW1(config-vlan)# exit | Exit the VLAN configuration mode. |
SW1(config)#lacp system-priority 20000 | Set the system priority of this switch. This priority is used for determining the system that is responsible for resolving conflicts in the choice of aggregation groups. A lower numerical value has a higher priority. |
SW1(config)#interface sa10 | Enter into port channel interface sa10. |
SW1(config-if)#switchport | Configure po10 as a layer 2 port. |
SW1(config-if)#bridge-group 1 | Associate bridge to an interface. |
SW1(config-if)#switchport mode trunk | Configure port as a trunk. |
SW1(config-if)#switchport trunk allowed vlan all | Allow all the VLANs on the po10 interface. |
SW1(config-if)#commit | Commit the candidate configuration to the running Configuration. |
SW1(config-if)#exit | Exit interface mode. |
SW1(config)#interface eth1 | Enter interface mode. |
SW1(config-if)#static-channel-group 10 | Add this interface to channel group 10 and enable link aggregation so that it can be selected for aggregation by the local system. |
SW1(config-if)#commit | Commit the candidate configuration to the running Configuration. |
SW1(config-if)#exit | Exit interface mode. |
SW1(config)#interface eth2 | Enter interface mode. |
SW1(config-if)#static-channel-group 10 | Add this interface to channel group 10 and enable link aggregation so that it can be selected for aggregation by the local system. |
SW1(config-if)#commit | Commit the candidate configuration to the running Configuration. |
SW1(config-if)#exit | Exit interface mode. |
SW1(config)#interface eth3 | Enter interface mode. |
SW1(config-if)#static-channel-group 10 | Add this interface to channel group 10 and enable link aggregation so that it can be selected for aggregation by the local system. |
SW1(config-if)#commit | Commit the candidate configuration to the running Configuration. |
SW1(config-if)#exit | Exit interface mode. |
SW2#configure terminal | Enter configure mode. |
SW2(config)# bridge 1 protocol mstp | Configure bridge 1 as MSTP bridge |
SW2(config)# vlan database | Enter VLAN database mode. |
SW2(config-vlan)# vlan 2-10 bridge 1 state enable | Configure a VLAN and add it to the bridge. |
SW2(config-vlan)# commit | Commit the candidate configuration to the running Configuration. |
SW2(config-vlan)# exit | Exit the VLAN configuration mode. |
SW2(config-if)#bridge-group 1 | Associate bridge to an interface. |
SW2(config-if)#switchport mode trunk | Configure port as a trunk. |
SW2(config-if)#switchport trunk allowed vlan all | Allow all the VLANs on the po10 interface. |
SW2(config-if)#commit | Commit the candidate configuration to the running Configuration. |
SW2(config-if)#exit | Exit interface mode. |
SW2(config)#interface eth2 | Enter interface mode. |
SW2(config-if)#static-channel-group 10 | Add this interface to channel group 10 and enable link aggregation so that it can be selected for aggregation by the local system. |
SW2(config-if)#commit | Commit the candidate configuration to the running Configuration. |
SW2(config-if)#exit | Exit interface mode. |
SW2(config)#interface eth3 | Enter interface mode. |
SW2(config-if)#static-channel-group 10 | Add this interface to channel group 10 and enable link aggregation so that it can be selected for aggregation by the local system. |
SW2(config-if)#exit | Exit interface mode. |
SW2(config)#interface eth4 | Enter interface mode. |
SW2(config-if)#static-channel-group 10 | Add this interface to channel group 10 and enable link aggregation so that it can be selected for aggregation by the local system. |
SW2(config-if)#commit | Commit the candidate configuration to the running Configuration. |
SW2(config-if)#exit | Exit interface mode. |