OcNOS-SP : Multi-Protocol Label Switching Guide : Multi-Protocol Label Switching Configuration Guide : BGP-VPLS Service Mapping Configuration : Configuration
Configuration
PE1: Loopback Interface
 
#configure terminal
Enter configuration mode.
(config)#interface lo
Enter the Interface mode for the loopback interface.
(config-if)#ip address 21.21.21.21/32 secondary
Configure IP address on loopback interface.
(config-if)#exit
Exit interface mode
PE1: Interface Configuration
 
(config)#interface xe2
Enter the Interface mode for xe2.
(config-if)# ip address 10.10.23.21/24
Configure IP address on the interface.
(config-if)#enable-rsvp
Enable RSVP on the physical interface
(config-if)# label-switching
Enable label switching on the interface.
(config-if)#exit
Exit interface mode
PE1: OSPF Configuration
 
(config)#router ospf 100
Enter the Router OSPF mode.
(config-router)#ospf router-id 21.21.21.21
Router-id configurations
(config-router)#network 21.21.21.21/32 area 0
Advertise loopback address in OSPF.
(config-router)#network 10.10.23.0/24 area 0
Advertise network address in OSPF.
(config-router)#exit
Exit Router OSPF mode and return to Configure mode.
PE1: Global RSVP
 
(config)#router rsvp
Enter the Router OSPF mode.
(config-router)#exit
Exit Router RSVP mode and return to Configure mode.
PE1: RSVP-Trunk Configuration
 
(config)#rsvp-trunk 1
Enter the Trunk configuration mode
(config-trunk)#to 23.23.23.23
Configure the destination of the Trunk
(config-trunk)#exit
Exit.Trunk configuration mode
PE1: BGP Configuration
 
(config)# router bgp 100
Enter the BGP configuration mode.
(config-router)#neighbor 23.23.23.23 remote-as 100
Configure neighbor
(config-router)#neighbor 23.23.23.23 update-source 21.21.21.21
Update loopback address as source
(config-router)#address-family l2vpn vpls
Enter address family mode.
(config-router-af)#neighbor 23.23.23.23 activate
Activate the neighbor.
(config-router-af)#exit
Exit address family mode.
(config-router)#exit
Exit Router BGP mode
PE1: BGP VPLS Configuration
 
(config)#mpls vpls v1 25
Enter VPLS config mode
(config)#service-tpid dot1.ad
Service tp-id configuration.
(config-vpls)#signaling bgp
Define Signaling as BGP
(config-vpls-sig)#ve-id 1
Configure VE-ID
(config-vpls-sig)#exit
Exit Signaling BGP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v2 26
Enter VPLS config mode
(config)#service-tpid dot1.ad
Service tp-id configuration.
(config-vpls)#signaling bgp
Define Signaling as BGP
(config-vpls-sig)#ve-id 1
Configure VE-ID
(config-vpls-sig)#exit
Exit Signaling BGP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v3 27
Enter VPLS config mode
(config-vpls)#signaling bgp
Define Signaling as BGP
(config-vpls-sig)#ve-id 1
Configure VE-ID
(config-vpls-sig)#exit
Exit Signaling BGP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v4 28
Enter VPLS config mode
(config-vpls)#signaling bgp
Define Signaling as BGP
(config-vpls-sig)#ve-id 1
Configure VE-ID
(config-vpls-sig)#exit
Exit Signaling BGP mode
(config-vpls)#exit
Exit VPLS mode
(config)#commit
Commit candidate configuration to running configuration
P1: Loopback Interface
 
#configure terminal
Enter configuration mode.
(config)#interface lo
Enter the Interface mode for the loopback interface.
(config-if)#ip address 22.22.22.22/32 secondary
Configure IP address on loopback interface.
(config-if)#exit
Exit interface mode
P1: Interface Configuration
 
(config)#interface xe1
Enter the Interface mode for xe1
(config-if)#ip address 10.10.23.22/24
Configure IP address on the interface.
(config-if)#enable-rsvp
Enable RSVP on the physical interface
(config-if)#label-switching
Enable label switching on the interface.
(config-if)#exit
Exit interface mode
(config)#interface xe2
Enter the Interface mode for xe2
(config-if)#ip address 10.10.21.22/24
Configure IP address on the interface.
(config-if)#enable-rsvp
Enable RSVP on the physical interface
(config-if)#label-switching
Enable label switching on the interface.
(config-if)#exit
Exit interface mode
P1: OSPF Configuration
 
(config)#router ospf 100
Enter the Router OSPF mode.
(config-router)#network 22.22.22.22/32 area 0
Advertise loopback address in OSPF.
(config-router)#network 10.10.23.0/24 area 0
Advertise network address in OSPF.
(config-router)#network 10.10.21.0/24 area 0
Advertise network address in OSPF.
(config-router)#exit
Exit Router OSPF mode and return to Configure mode.
P1: Global RSVP
 
(config)#router rsvp
Enter the Router OSPF mode.
(config-router)#exit
Exit Router RSVP mode and return to Configure mode.
(config)#commit
Commit candidate configuration to running configuration
PE2: Loopback Interface
 
#configure terminal
Enter configuration mode.
(config)#interface lo
Enter the Interface mode for the loopback interface.
(config-if)#ip address 23.23.23.23/32 secondary
Configure IP address on loopback interface.
(config-if)#exit
Exit interface mode
PE2: Interface Configuration
 
(config)#interface xe1
Enter the Interface mode for xe1
(config-if)#ip address 10.10.21.23/24
Configure IP address on the interface.
(config-if)#enable-rsvp
Enable RSVP on the physical interface
(config-if)#label-switching
Enable label switching on the interface.
(config-if)#exit
Exit interface mode
PE2: OSPF Configuration
 
(config)#router ospf 100
Enter the Router OSPF mode.
(config-router)#network 23.23.23.23/32 area 0
Advertise loopback address in OSPF.
(config-router)#network 10.10.21.0/24 area 0
Advertise network address in OSPF.
(config-router)#exit
Exit Router OSPF mode and return to Configure mode.
PE2: Global RSVP
 
(config)#router rsvp
Enter the Router OSPF mode.
(config-router)#exit
Exit Router RSVP mode and return to Configure mode.
PE2: RSVP-Trunk Configuration
 
(config)#rsvp-trunk 1
Enter the Trunk configuration mode
(config-trunk)#to 21.21.21.21
Configure the destination of the Trunk
(config-trunk)#exit
Exit.Trunk configuration mode
PE2: BGP Configuration
 
(config)# router bgp 100
Enter the BGP configuration mode.
(config-router)#neighbor 21.21.21.21 remote-as 100
Configure neighbor
(config-router)#neighbor 21.21.21.21 update-source 23.23.23.23
Update loopback address as source
(config-router)#address-family l2vpn vpls
Enter address family mode.
(config-router-af)#neighbor 21.21.21.21 activate
Activate the neighbor.
(config-router-af)#exit
Exit address family mode.
(config-router)#exit
Exit Router BGP mode
PE2: BGP VPLS Configuration
 
(config)#mpls vpls v1 25
Enter VPLS config mode
(config)#service-tpid dot1.ad
Service tp-id configuration.
(config-vpls)#signaling bgp
Define Signaling as BGP
(config-vpls-sig)#ve-id 2
Configure VE-ID
(config-vpls-sig)#exit
Exit Signaling BGP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v2 26
Enter VPLS config mode
(config)#service-tpid dot1.ad
Service tp-id configuration.
(config-vpls)#signaling bgp
Define Signaling as BGP
(config-vpls-sig)#ve-id 2
Configure VE-ID
(config-vpls-sig)#exit
Exit Signaling BGP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v3 27
Enter VPLS config mode
(config-vpls)#signaling bgp
Define Signaling as BGP
(config-vpls-sig)#ve-id 2
Configure VE-ID
(config-vpls-sig)#exit
Exit Signaling BGP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v4 28
Enter VPLS config mode
(config-vpls)#signaling bgp
Define Signaling as BGP
(config-vpls-sig)#ve-id 2
Configure VE-ID
(config-vpls-sig)#exit
Exit Signaling BGP mode
(config-vpls)#exit
Exit VPLS mode
(config)#commit
Commit candidate configuration to running configuration
Last modified date: 10/17/2023