OcNOS-SP : Multi-Protocol Label Switching Guide : Multi-Protocol Label Switching Configuration Guide : LDP-VPLS Service Mapping Configuration : Configuration
Configuration
PE1: Loopback Interface
 
#configure terminal
Enter configuration mode.
(config)#interface lo
Enter the Interface mode for the loopback interface.
(config-if)#ip address 21.21.21.21/32 secondary
Configure IP address on loopback interface.
(config-if)#exit
Exit interface mode
PE1: Global LDP
 
(config)#router ldp
Enter the Router LDP mode.
(config-router)#router-id 21.21.21.21
Set the router ID to IP address 21.21.21.21
(config-router)#transport-address ipv4 21.21.21.21
Configure transport address
(config-router)#targeted-peer ipv4 23.23.23.23
Configure targeted peer
(config-router)#targeted-peer #commit
Commit candidate configuration to the running configuration
(config-router-targeted-peer)#end
Exit from router target peer and LDP mode
PE1: Interface Configuration
 
#configure terminal
Enter configuration mode
(config)#interface xe2
Enter the Interface mode for xe2.
(config-if)# ip address 10.10.23.21/24
Configure IP address on the interface.
(config-if)#enable-ldp ipv4
Enable LDP on the physical interface
(config-if)# label-switching
Enable label switching on the interface.
(config-if)#exit
Exit interface mode
PE1: OSPF Configuration
 
(config)#router ospf 100
Enter the Router OSPF mode.
(config-router)#ospf router-id 21.21.21.21
Router-id configurations
(config-router)#network 21.21.21.21/32 area 0
Advertise loopback address in OSPF.
(config-router)#network 10.10.23.0/24 area 0
Advertise network address in OSPF.
(config-router)#exit
Exit Router OSPF mode and return to Configure mode.
PE1: LDP VPLS Configuration
 
(config)#mpls vpls v1 25
Enter VPLS config mode
(config-vpls)#service-tpid dot1.ad
Service tp-id configuration.
(config-vpls)#signaling ldp
Define Signaling as LDP
(config-vpls-sig)#vpls-type vlan
Type VLAN configuration for VPLS
(config-vpls-sig)#vpls-peer 23.23.23.23
Configure VPLS Peer
(config-vpls-sig)#exit-signaling
Exit Signaling LDP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v2 26
Enter VPLS config mode
(config-vpls)#service-tpid dot1.ad
Service tp-id configuration.
(config-vpls)#signaling ldp
Define Signaling as LDP
(config-vpls-sig)#vpls-type vlan
Type VLAN configuration for VPLS
(config-vpls-sig)#vpls-peer 23.23.23.23
Configure VPLS Peer
(config-vpls-sig)#exit-signaling
Exit Signaling LDP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v3 27
Enter VPLS config mode
(config-vpls)#signaling ldp
Define Signaling as LDP
(config-vpls-sig)#vpls-type vlan
Type VLAN configuration for VPLS
(config-vpls-sig)#vpls-peer 23.23.23.23
Configure VPLS Peer
(config-vpls-sig)# exit-signaling
Exit Signaling LDP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v4 28
Enter VPLS config mode
(config-vpls)#signaling ldp
Define Signaling as LDP
(config-vpls-sig)#vpls-type vlan
Type VLAN configuration for VPLS
(config-vpls-sig)#vpls-peer 23.23.23.23
Configure VPLS Peer
(config-vpls-sig)# exit-signaling
Exit Signaling LDP mode
(config-vpls)#exit
Exit VPLS mode
(config)#commit
Commit candidate configuration to the running configuration
P: Loopback Interface
 
#configure terminal
Enter configuration mode.
(config)#interface lo
Enter the Interface mode for the loopback interface.
(config-if)#ip address 22.22.22.22/32 secondary
Configure IP address on loopback interface.
(config-if)#exit
Exit interface mode
P: Global LDP
 
(config)#router ldp
Enter the Router LDP mode.
(config-router)#router-id 22.22.22.22
Set the router ID to IP address 22.22.22.22
(config-router)#transport-address ipv4 22.22.22.22
Configure transport address
(config-router)#commit
Commit candidate configuration to the running configuration
(config-router-targeted-peer)#end
Exit from router target peer and LDP mode
P: Interface Configuration
 
#configure terminal
Enter configuration mode
(config)#interface xe1
Enter the Interface mode for xe1.
(config-if)# ip address 10.10.23.22/24
Configure IP address on the interface.
(config-if)#enable-ldp ipv4
Enable LDP on the physical interface
(config-if)# label-switching
Enable label switching on the interface.
(config-if)#exit
Exit interface mode
(config)#interface xe2
Enter the Interface mode for xe2.
(config-if)# ip address 10.10.21.22/24
Configure IP address on the interface.
(config-if)#enable-ldp ipv4
Enable LDP on the physical interface
(config-if)# label-switching
Enable label switching on the interface.
(config-if)#exit
Exit interface mode
P: OSPF Configuration
 
(config)#router ospf 100
Enter the Router OSPF mode.
(config-router)#network 22.22.22.22/32 area 0
Advertise loopback address in OSPF.
(config-router)#network 10.10.23.0/24 area 0
Advertise network address in OSPF.
(config-router)#network 10.10.21.0/24 area 0
Advertise network address in OSPF.
(config-router)#exit
Exit Router OSPF mode and return to Configure mode.
(config)#commit
Commit candidate configuration to the running configuration
PE2: Loopback Interface
 
#configure terminal
Enter configuration mode.
(config)#interface lo
Enter the Interface mode for the loopback interface.
(config-if)#ip address 23.23.23.23/32 secondary
Configure IP address on loopback interface.
(config-if)#exit
Exit interface mode
PE2: Global LDP
 
(config)#router ldp
Enter the Router LDP mode.
(config-router)#router-id 23.23.23.23
Set the router ID to IP address 23.23.23.23
(config-router)#transport-address ipv4 23.23.23.23
Configure transport address
(config-router)#targeted-peer ipv4 21.21.21.21
Configure targeted peer
(config-router-targeted-peer)#commit
Commit candidate configuration to the running configuration
(config-router-targeted-peer)#end
Exit from router target peer and LDP mode
PE2: Interface Configuration
 
#configure terminal
Enter configuration mode.
(config)#interface xe1
Enter the Interface mode for xe1.
(config-if)# ip address 10.10.21.23/24
Configure IP address on the interface.
(config-if)#enable-ldp ipv4
Enable LDP on the physical interface
(config-if)# label-switching
Enable label switching on the interface.
(config-if)#exit
Exit interface mode
PE2: OSPF Configuration
 
(config)#router ospf 100
Enter the Router OSPF mode.
(config-router)#network 23.23.23.23/32 area 0
Advertise loopback address in OSPF.
(config-router)#network 10.10.21.0/24 area 0
Advertise network address in OSPF.
(config-router)#exit
Exit Router OSPF mode and return to Configure mode.
PE2: LDP VPLS Configuration
 
(config)#mpls vpls v1 25
Enter VPLS config mode
(config-vpls)#service-tpid dot1.ad
Service tp-id configuration.
(config-vpls)#signaling ldp
Define Signaling as LDP
(config-vpls-sig)#vpls-type vlan
Type VLAN configuration for VPLS
(config-vpls-sig)#vpls-peer 21.21.21.21
Configure VPLS Peer
(config-vpls-sig)# exit-signaling
Exit Signaling LDP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v2 26
Enter VPLS config mode
(config-vpls)#service-tpid dot1.ad
Service tp-id configuration.
(config-vpls)#signaling ldp
Define Signaling as LDP
(config-vpls-sig)#vpls-type vlan
Type VLAN configuration for VPLS
(config-vpls-sig)#vpls-peer 21.21.21.21
Configure VPLS Peer
(config-vpls-sig)# exit-signaling
Exit Signaling LDP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v3 27
Enter VPLS config mode
(config-vpls)#signaling ldp
Define Signaling as LDP
(config-vpls-sig)#vpls-type vlan
Type VLAN configuration for VPLS
(config-vpls-sig)#vpls-peer 21.21.21.21
Configure VPLS Peer
(config-vpls-sig)# exit-signaling
Exit Signaling LDP mode
(config-vpls)#exit
Exit VPLS mode
(config)#mpls vpls v4 28
Enter VPLS config mode
(config-vpls)#signaling ldp
Define Signaling as LDP
(config-vpls-sig)#vpls-type vlan
Type VLAN configuration for VPLS
(config-vpls-sig)#vpls-peer 21.21.21.21
Configure VPLS Peer
(config-vpls-sig)# exit-signaling
Exit Signaling LDP mode
(config-vpls)#exit
Exit VPLS mode
(config)#commit
Commit candidate configuration to the running configuration
Last modified date: 10/17/2023