#configure terminal | Enter configure mode. |
(config)#interface xe2 | Specify the interface (xe2) to be configured. |
(config-if)#ip address 10.10.10.1/24 | Configure IP address for the interface |
(config-if)#label-switching | Enable label switching on interface xe2. |
(config-if)#exit | Exit interface mode. |
(config)#interface lo | Specify the loopback (lo) interface to be configured. |
(config-if)#ip address 192.168.0.1/32 secondary | Set the IP address of the loopback interface to 192.168.0.1/32 |
(config-if)#commit | Commit the transaction. |
#configure terminal | Enter configure mode. |
(config)#router ospf 100 | Configure the routing process and specify the Process ID (100). The Process ID should be a unique positive integer identifying the routing process. |
(config-router)#network 10.10.10.0/24 area 0 (config-router)#network 192.168.0.1/32 area 0 | Define the interface on which OSPF runs and associate the area ID (0) with the interface. |
(config-router)#commit | Commit the transaction. |
#configure terminal | Enter configure mode. |
(config)#router ldp | Enter Router mode for LDP. |
(config-router)#router-id 192.168.0.1 | Set the router ID to IP address 192.168.0.1. |
(config-router)#transport-address ipv4 192.168.0.1 | Configure the transport address to be used for a TCP session over which LDP will run on an IPv4 interface. Note: It is preferable to use the loopback address as transport address. |
(config-router)#exit | Exit router mode. |
(config)#interface xe1 | Enter interface mode. |
(config-if)#enable-ldp ipv4 | Enable LDP on xe1. |
(config-if)#commit | Commit the transaction. |
#configure terminal | Enter configure mode. |
(config)#interface xe2 | Specify the interface (xe2) to be configured. |
(config-if)#ip address 10.10.10.2/24 | Configure IP address for the interface |
(config-if)#label-switching | Enable label switching on interface xe2. |
(config-if)#exit | Exit interface mode. |
(config)#interface xe1 | Specify the interface (xe1) to be configured. |
(config-if)#ip address 10.10.11.1/24 | Configure IP address for the interface |
(config-if)#label-switching | Enable label switching on interface xe1. |
(config-if)#exit | Exit interface mode. |
(config)#interface lo | Specify the loopback (lo) interface to be configured. |
(config-if)#ip address 192.168.0.2/32 secondary | Set the IP address of the loopback interface to 192.168.0.2/32 |
(config-if)#commit | Commit the transaction. |
#configure terminal | Enter configure mode. |
(config)#router ospf 100 | Configure the routing process and specify the Process ID (100). The Process ID should be a unique positive integer identifying the routing process. |
(config-router)#network 10.10.10.0/24 area 0 (config-router)#network 10.10.11.0/24 area 0 (config-router)#network 192.168.0.2/32 area 0 | Define the interface on which OSPF runs and associate the area ID (0) with the interface. |
(config-router)#commit | Commit the transaction. |
#configure terminal | Enter configure mode. |
(config)#router ldp | Enter Router mode for LDP. |
(config-router)#router-id 192.168.0.2 | Set the router ID to IP address 192.168.0.2. |
(config-router)#transport-address ipv4 192.168.0.2 | Configure the transport address to be used for a TCP session over which LDP will run on an IPv4 interface. Note: It is preferable to use the loopback address as transport address. |
(config-router)#exit | Exit router mode. |
(config)#interface xe1 | Enter interface mode. |
(config-if)#enable-ldp ipv4 | Enable LDP on xe1. |
(config-if)#exit | Exit interface mode. |
(config)#interface xe2 | Enter interface mode. |
(config-if)#enable-ldp ipv4 | Enable LDP on xe2. |
(config-if)#commit | Commit the transaction. |
#configure terminal | Enter configure mode. |
(config)#interface xe1 | Specify the interface (xe2) to be configured. |
(config-if)#ip address 10.10.11.2/24 | Configure IP address for the interface |
(config-if)#label-switching | Enable label switching on interface xe1. |
(config-if)#exit | Exit interface mode. |
(config)#interface lo | Specify the loopback (lo) interface to be configured. |
(config-if)#ip address 192.168.0.3/32 secondary | Set the IP address of the loopback interface to 192.168.0.3/32 |
(config-if)#commit | Commit the transaction. |
#configure terminal | Enter configure mode. |
(config)#router ospf 100 | Configure the routing process and specify the Process ID (100). The Process ID should be a unique positive integer identifying the routing process. |
(config-router)#network 10.10.11.0/24 area 0 (config-router)#network 192.168.0.3/32 area 0 | Define the interface on which OSPF runs and associate the area ID (0) with the interface. |
(config-router)#commit | Commit the transaction. |
#configure terminal | Enter configure mode. |
(config)#router ldp | Enter Router mode for LDP. |
(config-router)#router-id 192.168.0.3 | Set the router ID to IP address 192.168.0.3. |
(config-router)#explicit-null | To disable PHP. |
(config-router)#transport-address ipv4 192.168.0.3 | Configure the transport address to be used for a TCP session over which LDP will run on an IPv4 interface. Note: It is preferable to use the loopback address as transport address. |
(config-router)#exit | Exit router mode. |
(config)#interface xe2 | Enter interface mode. |
(config-if)#enable-ldp ipv4 | Enable LDP on xe2. |
(config-if)#commit | Commit the transaction. |