#configure terminal | Enter Configure mode |
(config)#bridge 1 protocol mstp | Create bridge 1 as an MSTP bridge (this step is not mandatory, but is a good practice to avoid layer 2 loops) |
(config)#vlan database | Create Vlan database |
(config-vlan)#vlan 10 bridge 1 | Configure Vlan 10 associated with bridge1 |
(config-vlan)#exit | Exit Interface mode |
(config)#ptp clock 0 profile e2e-transparent | Configure Switch as Transparent clock |
(config)#interface xe4 | Configure interface xe4 |
(config-if)#switchport | Configure xe4 as Layer 2 port |
(config-if)#bridge-group 1 | Configure xe4 in bridge group 1 |
(config-if)#switchport mode trunk | Configure mode trunk |
(config-if)#switchport trunk allowed vlan add 10 | Add vlan 10 to the interface xe4 |
(conig-if)#exit | Exit Interface mode |
(config)#interface xe6 | Configure interface xe6 |
(config-if)#switchport | Configure xe6 as Layer 2 port |
(config-if)#bridge-group 1 | Configure xe6 in bridge group 1 |
(config-if)#switchport mode trunk | Configure mode trunk |
(config-if)#switchport trunk allowed vlan add 10 | Add vlan 10 to the interface xe4 |
(conig-if)#exit | Exit Interface mode |
(config)#synce-interface ptp | Configure synce interface ptp |
(config-synce-if)#mode synchronous | Configure synchronous mode |
(config-synce-if)#input-source 1 | Configure the interface as an input source with priority 1 |
(config-synce-if)#quality-level QL_PRC | Configure QL-value. |
(config-synce-if)#mode synchronous | Configure synchronous mode. |
(config-synce-if)#wait-to-restore 0 | Configure Wait-to-Restore timer. |
(config-synce-if)#exit | Exit Interface configure mode |
(config)#interface xe6 | Configure interface xe6 |
(config-if)#ip address 192.168.5.103/24 | Configure Ipv4 address of interface |
(config-if)#exit | Exit interface mode |
(config)#ptp clock 0 profile g8265.1 | Enables G8265.1 for PTP time/phase telecom profile |
(config-ptp-clk)#slave-only | Configure the device as a Slave clock |
(config-clk-clk)#clock-port 1 | Configure ptp clock-port 1 |
(config-clk-port)#transport ipv4 | Configure transport as ipv4 |
(config-clk-port)#network-interface xe6 | Configure underlying interface that is used by this PTP Port |
(config-clk-port)#master ipv4 192.168.5.102 | Configure the master ipv4 address |
(config-clk-port)#exit | Exit ptp clock port mode |
#configure terminal | Enter Configure mode |
(config)#bridge 1 protocol mstp | Create bridge 1 as an MSTP bridge (this step is not mandatory, but is a good practice to avoid layer 2 loops) |
(config)#synce | Enter configure Synchronous Ethernet mode. |
(config-synce)#synchronization option 1 | Set the synchronization network type. |
(config-synce)#exit | Exit Synce mode |
(config)#synce-interface gps | Configure synce interface gps |
(config-synce-if)#mode synchronous | Configure synchronous mode |
(config-synce-if)#input-source 1 | Configure the interface as an input source with priority 1 |
(config-synce-if)#quality-level QL_PRC | Configure QL-value. |
(config-synce-if)#mode synchronous | Configure synchronous mode. |
(config-synce-if)#wait-to-restore 0 | Configure Wait-to-Restore timer. |
(config-synce-if)#exit | Exit Port Configure mode |
(config)#interface xe4 | Configure interface xe4 |
(config-if)#ip address 192.168.5.102/24 | Configure ipv4 address of xe4 |
(config-if)#exit | Exit interface mode |
(config)#ptp clock 0 profile g8265.1 | Enables G8265.1 for PTP time/phase telecom profile |
(config-ptp-clk)#clock-type tgm | Enables clock type as T-GM |
(config-ptp-clk)#number-ports 2 | Configure the number of PTP ports on the instance |
(config-ptp-clk)#clock-port 2 | Configure ptp clock-port 2 |
(config-ptp-clk)#transport ipv4 | Configure transport as ipv4 |
(config-clk-port)#master-only | Configure the port as an master-only port |
(config-clk-port)#network-interface xe4 | Configure underlying interface that is used by this PTP Port |
(config-clk-port)#exit | Exit ptp clock port mode |
(config-ptp-clk)#clock-port 1 | Configure ptp clock-port 1 |
(config-clk-port)#network-interface gps | Configure underlying interface that is used by this PTP Port |
(config-clk-port)#exit | Exit ptp clock port mode |