Access Control List Commands (XGS)

When you attach an access list to a VLAN interface or LAG interface as well as to a physical interface that is a member of that LAG and/or VLAN interface, the priority order is:

1. VLAN interface

2. LAG interface

3. Physical interface

For example, if you attach access lists to both a LAG interface and a physical interface that is a member of that LAG, matching traffic rules are applied to the LAG interface, but not to the physical interface.

Use the no form of this command to detach an ARP access group.

Note: To attach an ARP access-group to an interface, the ingress-arp TCAM group should be enabled. See the hardware-profile filter (XGS) command for more details.

Command Syntax

arp access-group NAME in

no arp access-group NAME in

Parameters

NAME

ARP Access list name

Command Mode

Interface mode

Applicability

This command was introduced in OcNOS version 1.3.6.

Example

#configure terminal

(config)#arp access-list ARP_ACL1

(config-arp-acl)#exit

(config)#interface xe1

(config-if)#arp access-group ARP_ACL1 in

(config-if)#no arp access-group ARP_ACL1 in

arp access-list

Use this command to define a named ARP access control list (ACL) that determines whether to accept or drop an incoming ARP packet based on the sender or target IP address, sender or target MAC address, ARP type.

An ACL is made up of one or more ACL specifications.

Each packet that arrives at the device is compared to each specification in each ACL in the order that they are sequenced. The device continues to look until it has a match. If no match is found and the device reaches the end of the list, the packet is denied by default. For this reason, place the most frequently occurring specifications at the top of the list.

The device stops checking the specifications after a match occurs.

There is an implied deny specification for traffic that is not permitted. The implied specification can be updated to permit if the use-case is to deny a certain set of ARP traffic.

Use the no form of this command to remove an ACL specification

Command Syntax

arp access-list NAME

no arp access-list NAME

Parameters

NAME

ARP Access list name

Command Mode

Configure mode

Applicability

This command was introduced in OcNOS version 1.3.6.

Example

#configure terminal

(config)#arp access-list ARP_ACL1

(config-arp-acl)#exit

(config)#no arp access-list ARP_ACL1

arp access-list filter

Use this command to configure access control entry in ARP access control list (ACL).

This determines whether to accept or drop an ARP packet based on the configured match criteria. Use the no form of this command to remove an ACL specification.

Note: Configuring the same filter again with a change of sequence number or change of action results in an update of sequence number or filter action.

Command Syntax

Parameters

deny

Drop the packet.

permit

Accept the packet.

<1-268435453>

ARP ACL sequence number.

request

RP request type

A.B.C.D/M

Source IP prefix and length.

A.B.C.D A.B.C.D

Source IP address and mask.

host A.B.C.D

Single source host IP address.

any

Match any source IP address.

any

Any source/destination.

XX-XX-XX-XX-XX-XX

Source MAC address (Option 1).

XX:XX:XX:XX:XX:XX

Source MAC address (Option 2).

XXXX.XXXX.XXXX

Source MAC address (Option 3).

XX-XX-XX-XX-XX-XX

Source wildcard (Option 1).

XX:XX:XX:XX:XX:XX

Source wildcard (Option 2).

XXXX.XXXX.XXXX

Source wildcard (Option 3).

vlan <1-4094>

VLAN identifier.

inner-vlan<1-4094>

Inner VLAN identifier.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

Command Mode

ARP access-list mode

Applicability

This command was introduced in OcNOS version 1.3.6.

Example

#configure terminal

(config)#arp access-list ARP_ACL1

(config-arp-acl)#15 permit ip host 2.2.2.1 mac any inner-vlan 3

(config-arp-acl)#no 15

arp access-list remark

Use this command to add a description to a named ARP access control list (ACL).

Use the no form of this command to remove an ACL description.

Command Syntax

remark LINE

no remark

Parameters

LINE

ACL description up to 100 characters.

Command Mode

ARP access-list mode

Applicability

This command was introduced in OcNOS version 1.3.6.

Example

#configure terminal

(config)#arp access-list arplist

(config-arp-acl)#remark permit the selected arp entries

(config-arp-acl)#exit

(config)#arp access-list arplist

(config-arp-acl)#no remark

(config-arp-acl)#exit

arp access-list resequence

Use this command to modify the sequence numbers of an ARP access list.

Note: IP Infusion Inc. recommends to use a non-overlapping sequence space for a new sequence number set to avoid unexpected rule matches during transition.

Command Syntax

resequence <1-268435453> INCREMENT

Parameters

<1-268435453>

Starting sequence number.

INCREMENT

Sequence number increment steps.

Command Mode

ARP access-list mode

Applicability

This command was introduced in OcNOS version 1.3.6.

Example

#configure terminal

(config)#ip access-list arplist

(config-arp-acl)#resequence 5 5

(config-arp-acl)#end

arp access-list response

Use this command to configure an ARP access control entry in an ARP access control list (ACL). This determines whether to accept or drop an ARP response packet based on the configured match criteria.

Use the no form of this command to remove an ACL specification.

Command Syntax

Parameters

deny

Drop the packet.

permit

Accept the packet.

<1-268435453>

ARP ACL sequence number.

response

ARP reply type

A.B.C.D/M

Source/Destination IP prefix and length.

A.B.C.D A.B.C.D

Source/Destination IP address and mask.

host A.B.C.D

A single source/destination host IP address.

any

Match any source/destination IP address.

any

Source/Destination any.

XX-XX-XX-XX-XX-XX

Source/Destination MAC address (Option 1).

XX:XX:XX:XX:XX:XX

Source/Destination MAC address (Option 2).

XXXX.XXXX.XXXX

Source/Destination MAC address (Option 3).

XX-XX-XX-XX-XX-XX

Source/Destination wildcard (Option 1).

XX:XX:XX:XX:XX:XX

Source/Destination wildcard (Option 2).

XXXX.XXXX.XXXX

Source/Destination wildcard (Option 3).

vlan <1-4094>

VLAN identifier.

inner-vlan <1-4094>

Inner VLAN identifier.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

Command Mode

ARP access-list mode

Applicability

This command was introduced in OcNOS version 1.3.6.

Example

#configure terminal

(config)#arp access-list ARP_ACL1

(config-arp-acl)#50 permit response ip host 2.2.2.1 any mac any any vlan 2

(config-arp-acl)#no 50 permit response ip host 2.2.2.1 any mac any any vlan 2

clear access-list

Use this command to clear the access-list counters.

Command Syntax

clear access-list (NAME|) counters

Parameters

NAME

Access-list name.

Command Mode

Exec mode and Privilege exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#clear access-list counters

clear access-list log-cache

Use this command to clear the access-list logging table.

Command Syntax

clear access-list log-cache

Parameters

None

Command Mode

Exec mode and Privilege exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#clear access-list log-cache

clear arp access-list

Use this command to clear the ARP access-list counters.

Command Syntax

clear arp access-list (NAME|) counters

Parameters

NAME

ARP access list name

Command Mode

Exec mode and privileged exec mode

Applicability

This command was introduced in OcNOS version 1.3.6.

Example

#clear arp access-list counters

clear ip access-list

Use this command to clear the IP access-list counters.

Command Syntax

clear ip access-list (NAME|) counters

Parameters

NAME

Access-list name.

Command Mode

Exec mode and Privilege exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#clear ip access-list counters

clear ipv6 access-list

Use this command to clear the IPv6 access-list counters.

Command Syntax

clear ipv6 access-list (NAME|) counters

Parameters

NAME

Access-list name.

Command Mode

Exec mode Privilege exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#clear ipv6 access-list counters

clear mac access-list

Use this command to clear the MAC access-list counters.

Command Syntax

clear mac access-list (NAME|) counters

Parameters

NAME

Access-list name.

Command Mode

Exec mode Privilege exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#clear mac access-list counters

ip access-group

Use this command to attach an IP access list to an interface or terminal line to filter incoming or outgoing IP packets.

The time-range parameter is optional. If used, the access-group is tied to the timer specified.

After the access-group has been configured with the time-range, to detach the access-group from the time-range, use the no form of this command with a time-range parameter as shown in the syntax and examples below.

To delete the access-group, use the no form of this command without a time-range.

Note: An egress IP ACL is supported on physical and lag interfaces only. An egress IP ACL will match only routed traffic and not switched traffic. VLAN and inner-VLAN options in ACL rules will match incoming packet VLANs even when ACL attached at egress.

Command Syntax

ip access-group NAME (in|out) (time-range TR_NAME|)

no ip access-group NAME (in|out) (time-range TR_NAME|)

Parameters

NAME

Access list name.

Filter incoming packets

out

Filter outgoing packets.

TR_NAME

Time range name set with the time-range command.

Command Mode

Line mode

Interface mode

Applicability

This command was introduced before OcNOS version 1.3. The time-range parameter was added in OcNOS-SP version 5.0.

Examples

#configure terminal

(config)#ip access-list mylist

(config-ip-acl)#permit ip any any

(config-ip-acl)#exit

(config)#hardware-profile filter ingress-ipv4-ext enable

(config)#interface xe3

(config-if)#ip access-group mylist in

(config-if)#exit

(config)#interface xe3

(config-if)#no ip access-group mylist in time-range TIMER1

(config-if)#exit

(config)#line vty

(config-all-line)#no ip access-group mylist in

Usage: VLANs and LAGs

When you attach an access list to a VLAN interface or LAG interface as well as to a physical interface that is a member of that LAG and/or VLAN interface, the priority order is:

1. VLAN interface

2. LAG interface

3. Physical interface

Usage: TCAM Groups

An access-group in the egress direction uses the TCAM group used by the QoS output service policy. Therefore, actions are unpredictable when conflicting matches are configured on same interface. IP Infusion Inc. recommends to avoid such a configuration. Otherwise, you need to configure the priority (in QoS) or the sequence number (in ACL) carefully to handle such cases.

To attach an IP ACL in the ingress direction, ensure the ingress-ipv4 TCAM group is enabled. See the hardware-profile filter (XGS) commands for details.

Usage: Loopback and VTY Interfaces

You can create ACLs for loopback (inband) and VTY interfaces to protect management applications such as SSH, Telnet, NTP, SNMP, and SNMP traps. Filtering TCP, UDP, and ICMP are supported.

Note: Loopback and VTY ACLs are mutually exclusive. If you set up one, you cannot set up the other.

For an ACL for a loopback interface, you create the ACL, configure it with rules, and associate the ACL with a loopback interface:

...

(config)#interface lo

(config-if)#ip access-group loopback in

For an ACL for VTY, you create the ACL, configure it with rules, and associate the ACL to the terminal line in line mode:

...

(config)#line vty

(config-all-line)#ip access-group vty in

Loopback and VTY ACLs do not support the following:

• The default rule deny all. You must explicitly set up a deny all rule based on your requirements.

• VLAN-specific rules.

• Rules with TCP flags.

• Rules with dscp, fragments, log, precedence, and sample parameters.

Usage: Timed ACL on interfaces

• You create a timer range that is identified by a name and configured with a start time, end time, and frequency. Once you create the time range, you can tie the ACL configuration to the time-range object. This allows you to create an access group that is enabled when the timer has started and disabled when the timer ends. You can also disassociate an access group from the timer if needed.

ip access-list

Use this command to define a named access control list (ACL) that determines whether to accept or drop an incoming IP packet based on specifications configured under the ACL. An ACL is made up of one or more ACL specifications.

Each packet that arrives at the device is compared to each specification in each ACL in the order that they are defined. The device continues to look until it has a match. If no match is found and the device reaches the end of the list, the packet is denied by default. For this reason, place the most frequently occurring specifications at the top of the list.

The device stops checking the specifications after a match occurs.

There is an implied deny specification for traffic that is not permitted. Implied specification can be updated to permit if the use-case is to deny a certain set of traffic.

Use the no form of this command to remove an ACL

Command Syntax

ip access-list NAME

no ip access-list NAME

Parameters

NAME

Access-list name.

Command Mode

Configure mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list ip-acl-01

ip access-list default

Use this command to modify the default rule action of access-list. Default rule is applicable only when access-list is attached to interface. Default rule will have the lowest priority and only the IP packets not matching any of the user defined rules match default rule.

Command Syntax

default (deny-all|permit-all) (log|) (sample|)

Parameters

deny-all

Drop all packets.

permit-all

Accept all packets.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

Command Mode

IP access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list ip-acl-01

(config-ip-acl)#default permit-all sample

ip access-list filter

Use this command to configure access control entry in an access control list (ACL).

This determines whether to accept or drop an IP packet based on the configured match criteria.

Use the no form of this command to remove an ACL specification. ACL specification can be removed using the sequence number as well.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

(<1-268435453>|) (deny|permit) (<0-255>|ahp|any|eigrp|esp|gre|ipip|ipcomp|ipv6ip |ospf|pim|rsvp|vrrp) (A.B.C.D/ M|A.B.C.D A.B.C.D|host A.B.C.D|any) (A.B.C.D/M|A.B.C.D A.B.C.D|host A.B.C.D|any) (dscp (<0-63>|af11| af12| af13| af21| af22| af23| af31|af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5|cs6| cs7| default| ef )|) (fragments|) (vlan <1-4094>|)(inner-vlan <1-4094>|) (log|) (sample|)((redirect-to-port IFNAME)|)

no (<1-268435453>|)(deny|permit)(<0-255> |ahp | any | eigrp | esp | gre | ipip | ipcomp | ipv6ip | ospf | pim | rsvp| vrrp) (A.B.C.D/ M|A.B.C.D A.B.C.D | host A.B.C.D|any) (A.B.C.D/M|A.B.C.D A.B.C.D|host A.B.C.D|any) (dscp (<0-63> |af11| af12| af13| af21| af22| af23| af31|af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5|cs6| cs7| default| ef )|) (fragments|) (vlan <1-4094>|)(inner-vlan <1-4094>|) (log|) (sample|)|)((redirect-to-port IFNAME)|)

no (<1-268435453>)

Parameters

<1-268435453>

IPv4 ACL sequence number.

deny

Drop the packet.

permit

Accept the packet.

<0-255>

IANA assigned protocol number.

any

Any protocol packet.

ahp

Authentication Header packet.

eigrp

Enhanced Interior Gateway Routing Protocol packet.

esp

Encapsulating Security Payload packet.

gre

Generic Routing Encapsulation packet.

ipip

IPv4 over IPv4 encapsulation packet.

ipcomp

IP Payload Compression Protocol packet.

ipv6ip

IPv6 over IPv4 encapsulation packet.

ospf

Open Shortest Path First packet.

pim

Protocol Independent Multicast packet

rsvp

Resource Reservation Protocol packet.

vrrp

Virtual Router Redundancy Protocol packet.

A.B.C.D/M

Source IP prefix and length.

A.B.C.D A.B.C.D

Source IP address and mask.

host A.B.C.D

A single source host IP address.

any

Match any source IP address.

A.B.C.D/M

Destination IP prefix and length.

A.B.C.D A.B.C.D

Destination IP address and mask.

host A.B.C.D

A single destination host IP address.

any

Any destination address

any

Match any destination IP address.

dscp

Match packets with given DSCP value.

<0-63>

Enter DSCP value between 0-63.

af11

AF11 DSCP (001010) decimal value 10.

af12

AF12 DSCP (001100) decimal value 12.

af13

AF13 DSCP (001110) decimal value 14.

af21

AF21 DSCP (010010) decimal value 18.

af22

AF22 DSCP (010100) decimal value 20.

af23

AF23 DSCP (010110) decimal value 22.

af31

AF31 DSCP (011010) decimal value 26.

af32

AF32 DSCP (011100) decimal value 28.

af33

AF33 DSCP (011110) decimal value 30.

af41

AF41 DSCP (100010) decimal value 34

af42

AF42 DSCP (100100) decimal value 36.

af43

AF43 DSCP (100110) decimal value 38.

cs1

CS1 (precedence 1) DSCP (001000) decimal value 8.

cs2

CS2 (precedence 2) DSCP (010000) decimal value 16.

cs3

CS3 (precedence 3) DSCP (011000) decimal value 24.

cs4

CS4 (precedence 4) DSCP (100000) decimal value 32.

cs5

CS5 (precedence 5) DSCP (101000) decimal value 40.

cs6

CS6 (precedence 6) DSCP (110000) decimal value 48.

cs7

CS7 (precedence 7) DSCP (111000) decimal value 56.

default

Default DSCP (000000) decimal value 0.

EF DSCP (101110) decimal value 46.

precedence

Match packets with given precedence value.

<0-7>

Enter precedence value 0-7.

critical

Match packets with critical precedence (5).

flash

Match packets with flash precedence (3).

flashoverride

Match packets with flash override precedence (4).

immediate

Match packets with immediate precedence (2).

internet

Match packets with internetwork control precedence (6).

network

Match packets with network control precedence (7).

priority

Match packets with priority precedence (1).

routine

Match packets with routine precedence (0).

fragments

Check non-initial fragments.

vlan

Match packets with given VLAN identifier.

<1-4094>

Enter VLAN identifier.

inner-vlan

Match packets with given inner VLAN identifier.

<1-4094>

Enter inner-VLAN identifier.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

redirect-to-port

Redirect the packet (in-direction only)

IFNAME

Interface name to which packet to be redirected

Command Mode

IP access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list ip-acl-01

(config-ip-acl)#11 permit any 30.0.0.1 0.0.0.255 172.124.0.2 0.0.0.255

(config-ip-acl)#no 11

ip access-list fragments

Use this command to configure access list to deny or permit all the IP fragmented packets.

Use the no form of this command to remove an ACL specification.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

(<1-268435453>|) fragments (deny-all|permit-all) (log|) (sample|)

no (<1-268435453>|) fragments (deny-all|permit-all) (log|) (sample|)

Parameters

deny-all

Drop the packet.

permit-all

Accept the packet.

<1-268435453>

IPv4 ACL sequence number.

fragments

Check non-initial.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

Command Mode

IP access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list mylist

(config-ip-acl)#fragments deny-all

(config-ip-acl)#end

ip access-list icmp

Use this command to permit or deny ICMP packets based on the given source and destination IP address. Even DSCP, precedence, VLAN identifier, inner VLAN identifier, and fragment number can be configured to permit or deny with the given values.

Use the no form of this command to remove an ACL specification.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

Parameters

<1-268435453>

IPv4 ACL sequence number.

deny

Drop the packet.

permit

Accept the packet.

icmp

Internet Control Message Protocol packet.

A.B.C.D/M

Source IP prefix and length.

A.B.C.D A.B.C.D

Source IP address and mask.

host A.B.C.D

A single source host IP address.

any

Match any source IP address.

A.B.C.D/M

Destination IP prefix and length.

A.B.C.D A.B.C.D

Destination IP address and mask.

host A.B.C.D

A single destination host IP address.

any

Match any destination IP address.

administratively-prohibited

Administratively prohibited.

alternate-address

Alternate address.

conversion-error

Datagram conversion.

dod-host-prohibited

Host prohibited.

dod-net-prohibited

Net prohibited.

echo

Echo (ping).

echo-reply

Echo reply.

general-parameter-problem

Parameter problem.

host-isolated

Host isolated.

host-precedence-unreachable

Host unreachable for precedence.

host-redirect

Host redirect.

host-tos-redirect

Host redirect for ToS.

host-tos-unreachable

Host unreachable for ToS.

host-unknown

Host unknown.

host-unreachable

Host unreachable.

information-reply

Information replies.

information-request

Information requests.

mask-reply

Mask replies.

mask-request

Mask requests.

mobile-redirect

Mobile host redirect.

net-redirect

Network redirect.

net-tos-redirect

Net redirect for ToS.

net-tos-unreachable

Network unreachable for ToS.

net-unreachable

Net unreachable.

network-unknown

Network unknown.

no-room-for-option

Parameter required but no room.

option-missing

Parameter required but not present.

packet-too-big

Fragmentation needed and DF set.

parameter-problem

All parameter problems.

port-unreachable

Port unreachable.

precedence-unreachable

Precedence cutoff.

protocol-unreachable

Protocol unreachable.

reassembly-timeout

Reassembly timeout.

redirect

All redirects.

router-advertisement

Router discovery advertisements.

router-solicitation

Router discovery solicitations.

source-quench

Source quenches.

source-route-failed

Source route failed.

time-exceeded

All time-exceeded messages.

timestamp-reply

Time-stamp replies.

timestamp-request

Time-stamp requests.

traceroute

Traceroute.

ttl-exceeded

TTL exceeded.

unreachable

All unreachables.

<0-255>

ICMP type.

<0-255>

ICMP code.

dscp

Match packets with given DSCP value.

<0-63>

Enter DSCP value between 0-63.

af11

AF11 DSCP (001010) decimal value 10.

af12

AF12 DSCP (001100) decimal value 12.

af13

AF13 DSCP (001110) decimal value 14.

af21

AF21 DSCP (010010) decimal value 18.

af22

AF22 DSCP (010100) decimal value 20.

af23

AF23 DSCP (010110) decimal value 22.

af31

AF31 DSCP (011010) decimal value 26.

af32

AF32 DSCP (011100) decimal value 28.

af33

AF33 DSCP (011110) decimal value 30.

af41

AF41 DSCP (100010) decimal value 34

af42

AF42 DSCP (100100) decimal value 36.

af43

AF43 DSCP (100110) decimal value 38.

cs1

CS1 (precedence 1) DSCP (001000) decimal value 8.

cs2

CS2 (precedence 2) DSCP (010000) decimal value 16.

cs3

CS3 (precedence 3) DSCP (011000) decimal value 24.

cs4

CS4 (precedence 4) DSCP (100000) decimal value 32.

cs5

CS5 (precedence 5) DSCP (101000) decimal value 40.

cs6

CS6 (precedence 6) DSCP (110000) decimal value 48.

cs7

CS7 (precedence 7) DSCP (111000) decimal value 56.

default

Default DSCP (000000) decimal value 0.

EF DSCP (101110) decimal value 46.

precedence

Match packets with given precedence value.

<0-7>

Enter precedence value 0-7.

critical

Match packets with critical precedence (5).

flash

Match packets with flash precedence (3).

flashoverride

Match packets with flash override precedence (4).

immediate

Match packets with immediate precedence (2).

internet

Match packets with internetwork control precedence (6).

network

Match packets with network control precedence (7).

priority

Match packets with priority precedence (1).

routine

Match packets with routine precedence (0).

fragments

Check non-initial fragments.

vlan

Match packets with given VLAN identifier.

<1-4094>

Enter VLAN identifier.

inner-vlan

Match packets with given inner VLAN identifier.

<1-4094>

Enter inner-VLAN identifier.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

redirect-to-port

Redirect the packet (in-direction only)

IFNAME

Interface name to which packet to be redirected

Command Mode

IP access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list ip-icmp

(config-ip-acl)#200 permit icmp any any

ip access-list remark

Use this command to add a description to a named IPv4 access control list (ACL).

Use the no form of this command to remove an ACL description.

Command Syntax

remark LINE

no remark

Parameters

LINE

ACL description up to 100 characters.

Command Mode

IP access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list mylist

(config-ip-acl)#remark permit the inside admin address

(config-ip-acl)#exit

(config)#ip access-list mylist

(config-ip-acl)#no remark

(config-ip-acl)#exit

ip access-list resequence

Use this command to modify the sequence numbers of an IP access list specification.

Note: Use a non-overlapping sequence space for new sequence number sets to avoid possible unexpected rule matches during transition.

Note: Re-sequencing an ACL attached to a management interface clears the ACL counters associated to it.

Command Syntax

resequence <1-268435453> INCREMENT

Parameters

<1-268435453>

Starting sequence number.

INCREMENT

Sequence number increment steps.

Command Mode

IP access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list mylist

(config-ip-acl)#resequence 5 5

(config-ip-acl)#end

ip access-list tcp|udp

Use this command to define a named access control list (ACL) that determines whether to accept or drop an incoming packet based on the criteria specified match criteria.

This form of this command filters packets based on source and destination IP address along with protocol (TCP or UDP) and port.

Use the no form of this command to remove an ACL specification.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

(<1-268435453>|) (deny|permit) tcp (A.B.C.D/M|A.B.C.D A.B.C.D|host A.B.C.D|any) ((eq|gt|lt|neq) (<0-65535>|bgp|chargen|cmd|daytime|discard|domain|drip|echo |exec|finger|ftp |ftp- data|gopher|hostname|ident|irc|klogin|kshell|login |lpd|nntp|pim-auto- rp|pop2|pop3|smtp|ssh|sunrpc|tacacs|talk|telnet|time| uucp|whois|www)| range <0-65535> <0-65535>|) (A.B.C.D/M|A.B.C.D A.B.C.D|host A.B.C.D|any) ((eq|gt|lt|neq) (<0-65535>|bgp|chargen|cmd|daytime|discard|domain| drip|echo|exec|finger|ftp|ftp-data|gopher|hostname|ident|irc|klogin|kshell|login |lpd|nntp|pim-auto- rp|pop2|pop3|smtp|ssh|sunrpc|tacacs|talk|telnet |time|uucp|whois|www) | range <0-65535> <0-65535>|) ((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef)) |(precedence (<0-7>| critical| flash | flashoverride| immediate| internet| network| priority| routine)) |) ({ack|established|fin|psh|rst|syn|urg}|) (fragments|)(vlan <1-4094>|)(inner-vlan <1-4094>|)(log|) (sample|)((redirect-to-port IFNAME)|)

no (<1-268435453>|) (deny|permit) tcp (A.B.C.D/M|A.B.C.D A.B.C.D|host A.B.C.D|any)((eq|gt|lt|neq) (<0-65535>| bgp| chargen| cmd| daytime| discard| domain| drip| echo|exec|finger|ftp |ftp- data |gopher |hostname| ident| irc| klogin| kshell|login|lpd|nntp|pim-auto- rp |pop2 |pop3 |smtp| ssh| sunrpc| tacacs |talk|telnet|time|uucp|whois|www) | range <0-65535> <0-65535>|) (A.B.C.D/M|A.B.C.D A.B.C.D|host A.B.C.D|any)((eq|gt|lt|neq) (<0-65535> |bgp |chargen |cmd |daytime|discard|domain|drip|echo|exec|finger|ftp|ftp-data| gopher| hostname| ident| irc| klogin| kshell| login| lpd| nntp| pim-auto-rp | pop2| pop3| smtp |ssh |sunrpc|tacacs|talk|telnet|time|uucp|whois|www) | range <0-65535> <0-65535>|) ((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef)) | (precedence (<0-7>| critical| flash | flashoverride| immediate| internet| network| priority| routine)) |) ({ack|established|fin|psh|rst|syn|urg}|) (fragments|)(vlan <1-4094>|)(inner-vlan <1-4094>|) (log|) (sample|) ((redirect-to-port IFNAME)|)

Parameters

<1-268435453>

IPv4 ACL sequence number.

deny

Drop the packet.

permit

Accept the packet.

tcp

Transmission Control Protocol.

udp

User Datagram Protocol.

A.B.C.D/M

Source or destination IP prefix and length.

A.B.C.D A.B.C.D

Source or destination IP address and mask.

host A.B.C.D

Source or destination host IP address.

any

Any source or destination IP address.

Source or destination port equal to.

Source or destination port greater than.

Source or destination port less than.

neq

Source or destination port not equal to.

<0-65535>

Source or destination port number.

range

Range of source or destination port numbers:

<0-65535>

Lowest value in the range.

<0-65535>

Highest value in the range.

bgp

Border Gateway Protocol.

chargen

Character generator.

cmd

Remote commands.

daytime

Daytime.

discard

Discard.

domain

Domain Name Service.

drip Dynamic Routing Information Protocol.

echo

Echo.

exec

EXEC.

finger

Finger.

ftp

File Transfer Protocol.

ftp-data

FTP data connections.

gopher

Gopher.

hostname

NIC hostname server.

ident

Ident Protocol.

irc

Internet Relay Chat.

klogin

Kerberos login.

kshell

Kerberos shell.

lpd

Printer service.

nntp

Network News Transport Protocol.

pim-auto-rp

PIM Auto-RP.

pop2

Post Office Protocol v2.

pop3

Post Office Protocol v3.

smtp

Simple Mail Transport Protocol.

ssh

Secure Shell.

sunrpc

Sun Remote Procedure Call.

tacacs

TAC Access Control System.

talk

Talk.

telnet

Telnet.

time

Time.

uucp

UNIX-to-UNIX Copy Program.

whois

WHOIS/NICNAME

www

World Wide Web.

nntp

Range of source or destination port numbers:

dscp

Match packets with given DSCP value.

<0-63>

Enter DSCP value between 0-63.

af11

AF11 DSCP (001010) decimal value 10.

af12

AF12 DSCP (001100) decimal value 12.

af13

AF13 DSCP (001110) decimal value 14.

af21

AF21 DSCP (010010) decimal value 18.

af22

AF22 DSCP (010100) decimal value 20.

af23

AF23 DSCP (010110) decimal value 22.

af31

AF31 DSCP (011010) decimal value 26.

af32

AF32 DSCP (011100) decimal value 28.

af33

AF33 DSCP (011110) decimal value 30.

af41

AF41 DSCP (100010) decimal value 34

af42

AF42 DSCP (100100) decimal value 36.

af43

AF43 DSCP (100110) decimal value 38.

cs1

CS1 (precedence 1) DSCP (001000) decimal value 8.

cs2

CS2 (precedence 2) DSCP (010000) decimal value 16.

cs3

CS3 (precedence 3) DSCP (011000) decimal value 24.

cs4

CS4 (precedence 4) DSCP (100000) decimal value 32.

cs5

CS5 (precedence 5) DSCP (101000) decimal value 40.

cs6

CS6 (precedence 6) DSCP (110000) decimal value 48.

cs7

CS7 (precedence 7) DSCP (111000) decimal value 56.

default

Default DSCP (000000) decimal value 0.

EF DSCP (101110) decimal value 46.

precedence

Match packets with given precedence value.

<0-7>

Enter precedence value 0-7.

critical

Match packets with critical precedence (5).

flash

Match packets with flash precedence (3).

flashoverride Match packets with flash override precedence (4).

immediate

Match packets with immediate precedence (2).

internet

Match packets with internetwork control precedence (6).

network

Match packets with network control precedence (7).

priority

Match packets with priority precedence (1).

routine

Match packets with routine precedence (0).

ack

Match on the Acknowledgment (ack) bit.

established

Matches only packets that belong to an established TCP connection.

fin

Match on the Finish (fin) bit.

psh

Match on the Push (psh) bit.

rst

Match on the Reset (rst) bit.

syn

Match on the Synchronize (syn) bit.

urg

Match on the Urgent (urg) bit.

biff

Biff.

bootpc

Bootstrap Protocol (BOOTP) client.

bootps

Bootstrap Protocol (BOOTP) server.

discard

Discard.

dnsix

DNSIX security protocol auditing.

domain

Domain Name Service.

echo

Echo.

isakmp

Internet Security Association and Key Management Protocol.

mobile-ip

Mobile IP registration.

nameserver

IEN116 name service.

netbios-dgm

Net BIOS datagram service.

netbios-ns

Net BIOS name service.

netbios-ss

Net BIOS session service.

non500-isakmp

Non500-Internet Security Association and Key Management Protocol.

ntp

Network Time Protocol.

pim-auto-rp

PIM Auto-RP.

rip

Routing Information Protocol.

snmp

Simple Network Management Protocol.

snmptrap

SNMP Traps.

sunrpc

Sun Remote Procedure Call.

syslog

System Logger.

tacacs

TAC Access Control System.

talk

Talk.

tftp

Trivial File Transfer Protocol.

time

Time.

who

Who service.

xdmcp

X Display Manager Control Protocol.

fragments

Check non-initial fragments.

vlan

Match packets with given VLAN identifier.

<1-4094>

Enter VLAN identifier.

inner-vlan

Match packets with given inner VLAN identifier.

<1-4094>

Enter inner-VLAN identifier.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

IFNAME

Interface name to which packet to be redirected

redirect-to-port

Redirect the packet (in-direction only)

Command Mode

IP access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list ip-acl-02

(config-ip-acl)#deny udp any any eq tftp

(config-ip-acl)#deny tcp any any eq ssh

(config-ip-acl)#end

ipv6 access-group

Use this command to attach an IPv6 access list to an interface to filter incoming or outgoing packets.

When you attach an access list to a VLAN interface or LAG interface as well as to a physical interface that is a member of that LAG and/or VLAN interface, the priority order is:

1. VLAN interface

2. LAG interface

3. Physical interface

Note: To attach an IPv6 access-group on interface, the IPv6 TCAM group should be enabled. To enable ingress-IPv6 /egress-IPv6, see the hardware-profile filter (XGS) command.

The time-range parameter is optional. If used, the access-group is tied to the timer specified.

To delete the access-group, use the no form of this command without a time-range.

Note: To attach IPv6 ACL in the ingress direction ingress-ipv6 TCAM group needs to be enabled. See the hardware-profile filter (XGS) command for details.

Command Syntax

ipv6 access-group NAME in (time-range TR_NAME|)

no ipv6 access-group NAME in (time-range TR_NAME|)

Parameters

NAME

Access list name.

TR_NAME

Time range name set with the time-range command.

Command Mode

Interface mode

Applicability

This command was introduced before OcNOS version 1.3. The time-range parameter was added in OcNOS-SP version 5.0.

Examples

#configure terminal

(config)#ipv6 access-list mylist

(config-ipv6-acl)#permit ipv6 any any

(config-ipv6-acl)#exit

(config)#hardware-profile filter ingress-ipv6 enable

(config)#interface xe3

(config-if)#ipv6 access-group mylist in

(config)#interface xe3

(config-if)#no ipv6 access-group mylist in

(config)#interface xe3

(config-if)#ipv6 access-group mylist in time-range TIMER1

(config)#interface xe3

(config-if)#no ipv6 access-group mylist in time-range TIMER1

ipv6 access-list

Use this command to define a IPv6 access control list (ACL) that determines whether to accept or drop an incoming IPv6 packet based on specifications configured under the ACL. An ACL is made up of one or more ACL specifications.

The device stops checking the specifications after a match occurs.

There is an implied deny specification for traffic that is not permitted. Implied specification can be updated to permit if the use-case is to deny a certain set of traffic.

Use the no form of this command to remove an ACL.

Note: For IPv6 routing protocols need neighbor discovery for the session to establish. Applying IPv6 ACLs implicitly drops all the ICMPv6 packets, thereby affecting the protocol sessions. To overcome this problem, implicit ICMPv6 permit rule is added in the IPv6 ACLs. If required behavior is to deny the ICMPv6, implicit rule can be deleted.

Command Syntax

ipv6 access-list NAME

no ipv6 access-list NAME

Parameters

NAME

Access-list name.

Command Mode

Configure mode

Applicability

This command was introduced before OcNOS version 1.3.

Implicit rule was introduced in OcNOS-OTN version 4.2

Examples

#configure terminal

(config)#ipv6 access-list ipv6-acl-01

(config-ipv6-acl)#exit

For example, create an IPv6 ACL:

(config)#ipv6 access-list ipv6-acl

#show ipv6 access-lists

IPv6 access list ip1

268435453 permit icmpv6 any any

Example of deleting this rule:

(config)#ipv6 access-list ipv6-acl

(config-ipv6-acl)#no 268435453 permit icmpv6 any any

#show ipv6 access-lists

IPv6 access list ip1

ipv6 access-list default

Use this command to modify the default rule action of access-list. Default rule is applicable only when access-list is attached to interface. Default rule will have the lowest priority and only the IPv6 packets not matching any of the user defined rules match default rule.

Command Syntax

default (deny-all|permit-all) (log|) (sample|)

Parameters

deny-all

Drop all packets.

permit-all

Accept all packets.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

Command Mode

IPv6 access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ip access-list ipv6-acl-01

(config-ipv6-acl)#default permit-all sample

ipv6 access-list filter

Use this command to define an access-control entry in an access control list (ACL) that determines whether to accept or drop an IPv6 packet based on the criteria specified. This form of this command filters packets based on:

• Protocol

• Source IP address

• Destination IP address

Use the no form of this command to remove an ACL specification. ACL specification can be removed using the sequence number as well.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Note: For IPv6 source and destination address filters, only the network part from the address (upper 64 bits) is supported due to hardware restriction. If the address length is more than 64 bits, it cannot be applied on the interfaces but it can be used with distributed lists in control plane protocols.

Command Syntax

(<1-268435453>|) (deny|permit)(<0-255>|ahp|any|eigrp|esp|gre|ipipv6|ipcomp |ipv6ipv6|ospf|pim|rsvp|vrrp) (X:X::X:X/ M|X:X::X:X X:X::X:X|host X:X::X:X|any) (X:X::X:X/M|X:X::X:X X:X::X:X|any) (dscp (<0-63>|af11| af12| af13| af21| af22| af23| af31|af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5|cs6| cs7| default| ef )|) (flow-label<0-1048575>|) (fragments|) (vlan <1-4094>|)(inner-vlan <1-4094>|) (log|) (sample|)((redirect-to-port IFNAME)|)

no (<1-268435453>|)(deny|permit)(<0-255>|ahp|any|eigrp|esp|gre|ipipv6|ipcomp |ipv6ipv6|ospf|pim|rsvp|vrrp) (X:X::X:X/ M|X:X::X:X X:X::X:X|host X:X::X:X|any) (X:X::X:X/M|X:X::X:X X:X::X:X|any) (dscp (<0-63>|af11| af12| af13| af21| af22| af23| af31|af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5|cs6| cs7| default| ef )|) (flow-label<0-1048575>|) (fragments|) (vlan <1-4094>|)(inner-vlan <1-4094>|) (log|) (sample|)((redirect-to-port IFNAME)|)

no (<1-268435453>)

Parameters

<1-268435453>

IPv4 ACL sequence number.

deny

Drop the packet.

permit

Accept the packet.

<0-255>

IANA assigned protocol number.

any

Any protocol packet.

ahp

Authentication Header packet.

eigrp

Enhanced Interior Gateway Routing Protocol packet.

esp

Encapsulating Security Payload packet.

gre

Generic Routing Encapsulation packet.

ipipv6

IPv4 over IPv6 Encapsulation packet.

ipcomp

IP Payload Compression Protocol packet.

ipv6ipv6

IPv6 over IPv6 Encapsulation packet.

ospf

Open Shortest Path First packet.

pim

Protocol Independent Multicast packet

rsvp

Resource Reservation Protocol packet.

vrrp

Virtual Router Redundancy Protocol packet.

X:X::X:X/M

Source Address with network mask length.

X:X::X:X X:X::X:X

Source Address with wild card mask.

any

Any source address.

X:X::X:X/M

Destination address with network mask length.

X:X::X:X X:X::X:X

Destination address with wild card mask.

any

Match any destination IP address.

dscp

Match packets with given DSCP value.

<0-63>

Enter DSCP value between 0-63.

af11

AF11 DSCP (001010) decimal value 10.

af12

AF12 DSCP (001100) decimal value 12.

af13

AF13 DSCP (001110) decimal value 14.

af21

AF21 DSCP (010010) decimal value 18.

af22

AF22 DSCP (010100) decimal value 20.

af23

AF23 DSCP (010110) decimal value 22.

af31

AF31 DSCP (011010) decimal value 26.

af32

AF32 DSCP (011100) decimal value 28.

af33

AF33 DSCP (011110) decimal value 30.

af41

AF41 DSCP (100010) decimal value 34

af42

AF42 DSCP (100100) decimal value 36.

af43

AF43 DSCP (100110) decimal value 38.

cs1

CS1 (precedence 1) DSCP (001000) decimal value 8.

cs2

CS2 (precedence 2) DSCP (010000) decimal value 16.

cs3

CS3 (precedence 3) DSCP (011000) decimal value 24.

cs4

CS4 (precedence 4) DSCP (100000) decimal value 32.

cs5

CS5 (precedence 5) DSCP (101000) decimal value 40.

cs6

CS6 (precedence 6) DSCP (110000) decimal value 48.

cs7

CS7 (precedence 7) DSCP (111000) decimal value 56.

default

Default DSCP (000000) decimal value 0.

EF DSCP (101110) decimal value 46.

vlan

Match packets with given VLAN identifier.

<1-4094>

VLAN identifier.

inner-vlan

Match packets with given inner VLAN identifier.

<1-4094>

Inner-VLAN identifier.

redirect-to-port

Redirect the packet (in-direction only)

IFNAME

Interface name to which packet to be redirected

Command Mode

IPv6 access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ipv6 access-list ipv6-acl-01

(config-ip-acl)#permit ipipv6 any any

(config-ip-acl)#end

ipv6 access-list fragments

Use this command to permit or deny all the IPv6 fragments.

Use the no form of this command to remove an ACL specification.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

(<1-268435453>|) fragments (deny-all|permit-all) (log|) (sample|)

no (<1-268435453>|) fragments (deny-all|permit-all) (log|) (sample|)

Parameters

<1-268435453>

IPv6 ACL sequence number.

fragments

Check non-initial fragments.

deny-all

Specify packets to reject.

permit-all

Specify packets to forward.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

Command Mode

IPv6 access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ipv6 access-list mylist

(config-ipv6-acl)#fragments deny-all

ipv6 access-list icmpv6

Use this command to permit or deny IPv6 ICMP packets with the given source and destination IPv6 address, DSCP value, VLAN identifier, inner VLAN identifier, fragments, and flow label.

Use the no form of this command to remove an ACL specification.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

Parameters

<1-268435453>

IPv6 ACL sequence number.

deny

Drop the packet.

permit

Accept the packet.

icmpv6

Internet Control Message Protocol packet.

X:X::X:X/M

Source Address with network mask length.

X:X::X:X X:X::X:X

Source Address with wild card mask.

any

Any source address.

X:X::X:X/M

Destination address with network mask length.

X:X::X:X X:X::X:X

Destination address with wild card mask.

any

Any destination address

beyond-scope

Destination beyond scope

destination-unreachable

Destination address is unreachable

echo-reply

Echo reply

echo-request

Echo request (ping)

header

Parameter header problems

hop-limit

Hop limit exceeded in transit

mld-query

Multicast Listener Discovery Query

mld-reduction

Multicast Listener Discovery Reduction

mld-report

Multicast Listener Discovery Report

nd-na

Neighbor discovery neighbor advertisements

nd-ns

Neighbor discovery neighbor solicitations

next-header

Parameter next header problems

no-admin

Administration prohibited destination

no-route

No route to destination

packet-too-big

Packet too big

parameter-option

Parameter option problems

parameter-problem

All parameter problems

port-unreachable

Port unreachable

reassembly-timeout

Reassembly timeout

redirect

Neighbor redirect

renum-command

Router renumbering command

renum-result

Router renumbering result

renum-seq-number

Router renumbering sequence number reset

router-advertisement

Neighbor discovery router advertisements

router-renumbering

All router renumbering

router-solicitation

Neighbor discovery router solicitations

time-exceeded

All time exceeded messages

unreachable

All unreachable

<0-255>

ICMPv6 message type

<0-255>

ICMPv6 message code

dscp

Match packets with given DSCP value.

<0-63>

Enter DSCP value between 0-63.

af11

AF11 DSCP (001010) decimal value 10.

af12

AF12 DSCP (001100) decimal value 12.

af13

AF13 DSCP (001110) decimal value 14.

af21

AF21 DSCP (010010) decimal value 18.

af22

AF22 DSCP (010100) decimal value 20.

af23

AF23 DSCP (010110) decimal value 22.

af31

AF31 DSCP (011010) decimal value 26.

af32

AF32 DSCP (011100) decimal value 28.

af33

AF33 DSCP (011110) decimal value 30.

af41

AF41 DSCP (100010) decimal value 34

af42

AF42 DSCP (100100) decimal value 36.

af43

AF43 DSCP (100110) decimal value 38.

cs1

CS1 (precedence 1) DSCP (001000) decimal value 8.

cs2

CS2 (precedence 2) DSCP (010000) decimal value 16.

cs3

CS3 (precedence 3) DSCP (011000) decimal value 24.

cs4

CS4 (precedence 4) DSCP (100000) decimal value 32.

cs5

CS5 (precedence 5) DSCP (101000) decimal value 40.

cs6

CS6 (precedence 6) DSCP (110000) decimal value 48.

cs7

CS7 (precedence 7) DSCP (111000) decimal value 56.

default

Default DSCP (000000) decimal value 0.

EF DSCP (101110) decimal value 46.

flow-label

IPv6 Flow-label.

<0-1048575>

IPv6 Flow-label value.

fragments

Check non-initial fragments.

vlan

Match packets with given VLAN identifier.

<1-4094>

Enter VLAN identifier.

inner-vlan

Match packets with given inner VLAN identifier.

<1-4094>

Enter inner-VLAN identifier.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

redirect-to-port

Redirect the packet (in-direction only)

IFNAME

Interface name to which packet to be redirected

Command Mode

IPv6 access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ipv6 access-list mylist

(config-ipv6-acl)#200 permit icmpv6 any any fragments

ipv6 access-list remark

Use this command to add a description to an IPv6 access control list (ACL).

Use the no form of this command to remove an access control list description.

Command Syntax

remark LINE

no remark

Parameters

LINE

ACL description up to 100 characters.

Command Mode

IPv6 access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ipv6 access-list mylist

(config-ipv6-acl)#remark Permit the inside admin address

ipv6 access-list resequence

Use this command to modify the sequence numbers of an IPv6 access list specification.

Note: Use a non-overlapping sequence space for new sequence number sets to avoid possible unexpected rule matches during transition.

Note: Re-sequencing an ACL attached to a management interface clears the ACL counters associated to it.

Command Syntax

resequence <1-268435453> INCREMENT

Parameters

<1-268435453>

Starting Sequence number.

INCREMENT

Sequence number increment steps.

Command Mode

IPv6 access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ipv6 access-list mylist

(config-ipv6-acl)#resequence 15 15

ipv6 access-list sctp

Use this command to allow ACL to permit or deny SCTP packets based on the given source and destination IPV6 address. Even DSCP, VLAN identifier, inner VLAN identifier, flow label, and fragment can be configured to permit or deny with the given values.

Use the no form of this command to remove an ACL specification.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

(<1-268435453>|) (deny|permit) (sctp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) (X:X::X:X/ M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>) | (range <0-65535> <0-65535>)| (fragments)| } (dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef)|) ((flow-label <0-1048575>)|)(fragments|)(vlan <1-4094>|)(inner-vlan <1-4094>|) (log|) (sample|)((redirect-to-port IFNAME)|)

no (<1-268435453>|) (deny|permit) (sctp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>) | (range <0-65535> <0-65535>)| (fragments)| } (dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef)|) ((flow-label <0-1048575>)|) (fragments|)(vlan <1-4094>|)(inner-vlan <1-4094>|)(log|) (sample|)((redirect-to-port IFNAME)|)

Parameters

<1-268435453>

IPv6 ACL sequence number.

deny

Drop the packet.

permit

Accept the packet.

sctp

Stream Control Transmission Protocol packet.

X:X::X:X/M

Source address with network mask length.

X:X::X:X

Source address with wild card mask.

X:X::X:X

Source address's wild card mask (ignored bits).

any

Any source address.

X:X::X:X/M

Destination address with network mask length.

X:X::X:X

Destination address with wild card mask.

X:X::X:X

Destination address's wild card mask (ignored bits).

any

Any destination address.

Source or destination port equal to.

Source or destination port greater than.

Source or destination port less than.

neq

Source or destination port not equal to.

<0-65535>

Source or destination port number.

range

Range of source or destination port numbers:

<0-65535>

Lowest value in the range.

<0-65535>

Highest value in the range.

dscp

Match packets with given DSCP value.

<0-63>

Enter DSCP value between 0-63.

af11

AF11 DSCP (001010) decimal value 10.

af12

AF12 DSCP (001100) decimal value 12.

af13

AF13 DSCP (001110) decimal value 14.

af21

AF21 DSCP (010010) decimal value 18.

af22

AF22 DSCP (010100) decimal value 20.

af23

AF23 DSCP (010110) decimal value 22.

af31

AF31 DSCP (011010) decimal value 26.

af32

AF32 DSCP (011100) decimal value 28.

af33

AF33 DSCP (011110) decimal value 30.

af41

AF41 DSCP (100010) decimal value 34

af42

AF42 DSCP (100100) decimal value 36.

af43

AF43 DSCP (100110) decimal value 38.

cs1

CS1 (precedence 1) DSCP (001000) decimal value 8.

cs2

CS2 (precedence 2) DSCP (010000) decimal value 16.

cs3

CS3 (precedence 3) DSCP (011000) decimal value 24.

cs4

CS4 (precedence 4) DSCP (100000) decimal value 32.

cs5

CS5 (precedence 5) DSCP (101000) decimal value 40.

cs6

CS6 (precedence 6) DSCP (110000) decimal value 48.

cs7

CS7 (precedence 7) DSCP (111000) decimal value 56.

default

Default DSCP (000000) decimal value 0.

EF DSCP (101110) decimal value 46.

flow-label

IPv6 Flow-label.

<0-1048575>

IPv6 Flow-label value.

fragments

Check non-initial fragments.

vlan

Match packets with given VLAN identifier.

<1-4094>

Enter VLAN identifier.

inner-vlan

Match packets with given inner VLAN identifier.

<1-4094>

Enter inner-VLAN identifier.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

redirect-to-port

Redirect the packet (in-direction only)

IFNAME

Interface name to which packet to be redirected

Command Mode

IPv6 access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ipv6 access-list mylist

(config-ipv6-acl)#200 permit sctp any any fragments

ipv6 access-list tcp|udp

Use this command to define a IPv6 access control list (ACL) specification that determines whether to accept or drop an incoming IPv6 packet based on the criteria that you specify. This form of this command filters packets based on source and destination IPv6 address along with protocol (TCP or UDP) and port.

Use the no form of this command to remove an ACL specification.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

(<1-268435453>|)(deny|permit) (tcp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|bgp|chargen|cmd|daytime| discard|domain|drip|echo|exec|finger|ftp |ftp-data|gopher|hostname|ident|irc|klogin|kshell|login|lpd|nntp|pim-auto-rp|pop2|pop3|smtp|ssh|sunrpc|tacacs|talk|telnet|time|uucp|whois|www)| (range <0-65535> <0-65535>)| (fragments) |} (((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef ))|) (flow-label <0-1048575>|) ({ack|established|fin|psh|rst|syn|urg}|)) (vlan <1-4094>|) (inner-vlan <1-4094>|) (log|) (sample|)

(<1-268435453>|)(deny|permit) (tcp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|bgp|chargen|cmd|daytime|discard|domain|drip| echo|exec|finger|ftp |ftp-data|gopher|hostname|ident|irc|klogin|kshell |login|lpd|nntp|pim-auto-rp|pop2|pop3|smtp|ssh|sunrpc|tacacs|talk|telnet |time|uucp|whois|www) | (range <0-65535> <0-65535>)} (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|bgp|chargen|cmd|daytime|discard|domain| drip|echo|exec|finger|ftp |ftp-data|gopher|hostname|ident|irc|klogin|kshell| login|lpd|nntp|pim-auto-rp|pop2|pop3|smtp|ssh|sunrpc|tacacs| talk|telnet|time|uucp|whois|www) | (range <0-65535> <0-65535>)|} (((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef ))|) (flow-label <0-1048575>|) ({ack|established|fin|psh|rst|syn|urg}|)) (vlan <1-4094>|) (inner-vlan <1-4094>|) (log|) (sample|) ((redirect-to-port IFNAME)|)

(<1-268435453>|)(deny|permit) (udp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|biff|bootpc|bootps|discard |dnsix|domain|echo|isakmp|mobile-ip|nameserver|netbios-dgm|netbios-ns|netbios-ss|non500-isakmp|ntp|pim-auto-rp|rip|snmp|snmptrap|sunrpc|syslog| tacacs|talk|tftp|time|who|xdmcp) | (range <0-65535> <0-65535>) | (fragments) |} ((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef ))|) (flow-label <0-1048575>|) (vlan <1-4094>|) (inner-vlan <1-4094>|) (log|) (sample|) ((redirect-to-port IFNAME)|)

(<1-268435453>|)(deny|permit) (udp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|biff|bootpc|bootps|discard|dnsix |domain|echo|isakmp|mobile-ip|nameserver|netbios-dgm|netbios-ns|netbios-ss|non500-isakmp|ntp|pim-auto-rp|rip|snmp|snmptrap|sunrpc|syslog| tacacs|talk|tftp|time|who|xdmcp) | (range <0-65535> <0-65535>) } (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|biff|bootpc|bootps|discard| dnsix|domain|echo|isakmp|mobile-ip|nameserver|netbios-dgm|netbios-ns|netbios-ss|non500-isakmp|ntp|pim-auto-rp|rip|snmp|snmptrap|sunrpc| syslog|tacacs|talk|tftp|time|who|xdmcp) | (range <0-65535> <0-65535>) } ((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef ))|) (flow-label <0-1048575>|) (vlan <1-4094>|) (inner-vlan <1-4094>|) (log|) (sample|) ((redirect-to-port IFNAME)|)

no (<1-268435453>|)(deny|permit) (tcp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|bgp|chargen|cmd| daytime|discard|domain|drip|echo|exec|finger|ftp |ftp-data|gopher|hostname |ident|irc|klogin|kshell|login|lpd|nntp|pim-auto-rp|pop2|pop3|smtp|ssh|sunrpc |tacacs|talk|telnet|time|uucp|whois|www)| (range <0-65535> <0-65535>)| (fragments) |} (((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef ))|) (flow-label <0-1048575>|) ({ack|established|fin|psh|rst|syn|urg}|)) (vlan <1-4094>|) (inner-vlan <1-4094>|) (log|) (sample|)

no (<1-268435453>|)(deny|permit) (tcp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|bgp|chargen|cmd|daytime|discard|domain|drip |echo|exec|finger|ftp |ftp-data|gopher|hostname|ident|irc|klogin|kshell |login|lpd|nntp|pim-auto-rp|pop2|pop3|smtp|ssh|sunrpc|tacacs|talk|telnet |time|uucp|whois|www) | (range <0-65535> <0-65535>)} (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|bgp|chargen|cmd|daytime|discard| domain|drip|echo|exec|finger|ftp |ftp-data|gopher|hostname|ident|irc|klogin| kshell|login|lpd|nntp|pim-auto-rp|pop2|pop3|smtp|ssh|sunrpc|tacacs|talk |telnet|time|uucp|whois|www) | (range <0-65535> <0-65535>)|} (((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef ))|) (flow-label <0-1048575>|) ({ack|established|fin|psh|rst|syn|urg}|)) (vlan <1-4094>|) (inner-vlan <1-4094>|) (log|) (sample|) ((redirect-to-port IFNAME)|

no (<1-268435453>|)(deny|permit) (udp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|biff|bootpc|bootps|discard|dnsix|domain|echo|isakmp|mobile-ip|nameserver|netbios-dgm|netbios-ns|netbios-ss|non500-isakmp|ntp|pim-auto-rp|rip|snmp|snmptrap|sunrpc|syslog|tacacs|talk|tftp|time|who|xdmcp) | (range <0-65535> <0-65535>) | (fragments) |} ((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef ))|) (flow-label <0-1048575>|) (vlan <1-4094>|) (inner-vlan <1-4094>|) (log|) (sample|) ((redirect-to-port IFNAME)|)

no (<1-268435453>|)(deny|permit) (udp) (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|biff|bootpc|bootps|discard|dnsix|domain|echo|isakmp|mobile-ip|nameserver|netbios-dgm|netbios-ns|netbios-ss|non500-isakmp|ntp|pim-auto-rp|rip|snmp|snmptrap|sunrpc|syslog|tacacs|talk|tftp|time|who|xdmcp) | (range <0-65535> <0-65535>) } (X:X::X:X/M|X:X::X:X X:X::X:X|any) {(eq|gt|lt|neq) (<0-65535>|biff|bootpc|bootps|discard|dnsix|domain|echo|isakmp|mobile-ip|nameserver|netbios-dgm|netbios-ns|netbios-ss|non500-isakmp|ntp|pim-auto-rp|rip|snmp|snmptrap|sunrpc|syslog|tacacs|talk|tftp|time|who|xdmcp) | (range <0-65535> <0-65535>) } ((dscp (<0-63>| af11| af12| af13| af21| af22| af23| af31| af32| af33| af41| af42| af43| cs1| cs2| cs3| cs4| cs5| cs6| cs7| default| ef ))|) (flow-label <0-1048575>|) (vlan <1-4094>|) (inner-vlan <1-4094>|) (log|) (sample|) ((redirect-to-port IFNAME)|)

Parameters

<1-268435453>

IPv6 ACL sequence number.

deny

Drop the packet.

permit

Accept the packet.

tcp

Transmission Control Protocol.

udp

User Datagram Protocol.

X:X::X:X/M

Source or destination IPv6 prefix and length.

X:X::X:X X:X::X:X

Source or destination IPv6 address and mask.

host X:X::X:X

A single source or destination host IPv6 address.

any

Any source or destination IPv6 address.

Source or destination port equal to.

Source or destination port greater than.

Source or destination port less than.

neq

Source or destination port not equal to.

<0-65535>

Source or destination port number.

range

Range of source or destination port numbers:

<0-65535>

Lowest value in the range.

<0-65535>

Highest value in the range.

ftp

File Transfer Protocol (21).

ssh

Secure Shell (22).

telnet

Telnet (23).

www

World Wide Web (HTTP 80).

tftp

Trivial File Transfer Protocol (69).

bootp

Bootstrap Protocol (BOOTP) client (67).

bgp

Border Gateway Protocol.

chargen

Character generator.

cmd

Remote commands.

daytime

Daytime.

discard

Discard.

domain

Domain Name Service.

drip

Dynamic Routing Information Protocol.

echo

Echo.

exec

EXEC.

finger

Finger.

ftp

File Transfer Protocol.

ftp-data

FTP data connections.

gopher

Gopher.

hostname

NIC hostname server.

ident

Ident Protocol.

irc

Internet Relay Chat.

klogin

Kerberos login.

kshell

Kerberos shell.

lpd

Printer service.

nnt

Network News Transport Protocol.

pim-auto-rp

PIM Auto-RP.

pop2

Post Office Protocol v2.

pop3

Post Office Protocol v3.

smtp

Simple Mail Transport Protocol.

ssh

Secure Shell.

sunrpc

Sun Remote Procedure Call.

tacacs

TAC Access Control System.

talk

Talk.

telnet

Telnet.

time

Time.

uucp

UNIX-to-UNIX Copy Program.

whois

WHOIS/NICNAME

www

World Wide Web.

nntp

Range of source or destination port numbers:

dscp

Match packets with given DSCP value.

<0-63>

Enter DSCP value between 0-63.

af11

AF11 DSCP (001010) decimal value 10.

af12

AF12 DSCP (001100) decimal value 12.

af13

AF13 DSCP (001110) decimal value 14.

af21

AF21 DSCP (010010) decimal value 18.

af22

AF22 DSCP (010100) decimal value 20.

af23

AF23 DSCP (010110) decimal value 22.

af31

AF31 DSCP (011010) decimal value 26.

af32

AF32 DSCP (011100) decimal value 28.

af33

AF33 DSCP (011110) decimal value 30.

af41

AF41 DSCP (100010) decimal value 34

af42

AF42 DSCP (100100) decimal value 36.

af43

AF43 DSCP (100110) decimal value 38.

cs1

CS1 (precedence 1) DSCP (001000) decimal value 8.

cs2

CS2 (precedence 2) DSCP (010000) decimal value 16.

cs3

CS3 (precedence 3) DSCP (011000) decimal value 24.

cs4

CS4 (precedence 4) DSCP (100000) decimal value 32.

cs5

CS5 (precedence 5) DSCP (101000) decimal value 40.

cs6

CS6 (precedence 6) DSCP (110000) decimal value 48.

cs7

CS7 (precedence 7) DSCP (111000) decimal value 56.

default

Default DSCP (000000) decimal value 0.

EF DSCP (101110) decimal value 46.

precedence

Match packets with given precedence value.

<0-7>

Enter precedence value 0-7.

critical

Match packets with critical precedence (5).

flash

Match packets with flash precedence (3).

flashoverride

Match packets with flash override precedence (4).

immediate

Match packets with immediate precedence (2).

internet

Match packets with internetwork control precedence (6).

network

Match packets with network control precedence (7).

priority

Match packets with priority precedence (1).

routine

Match packets with routine precedence (0).

ack

Match on the Acknowledgment (ack) bit.

established

Matches only packets that belong to an established TCP connection.

fin

Match on the Finish (fin) bit.

psh

Match on the Push (psh) bit.

rst

Match on the Reset (rst) bit.

syn

Match on the Synchronize (syn) bit.

urg

Match on the Urgent (urg) bit.

biff

Biff.

bootpc

Bootstrap Protocol (BOOTP) client.

bootps

Bootstrap Protocol (BOOTP) server.

discard

Discard.

dnsix

DNSIX security protocol auditing.

domain

Domain Name Service.

echo

Echo.

isakmp

Internet Security Association and Key Management Protocol.

mobile-ip

Mobile IP registration.

nameserver

IEN116 name service.

netbios-dgm

Net BIOS datagram service.

netbios-ns

Net BIOS name service.

netbios-ss

Net BIOS session service.

non500-isakmp

Non500-Internet Security Association and Key Management Protocol.

ntp

Network Time Protocol.

pim-auto-rp

PIM Auto-RP.

rip

Routing Information Protocol.

snmp

Simple Network Management Protocol.

snmptrap

SNMP Traps.

sunrpc

Sun Remote Procedure Call.

syslog

System Logger.

tacacs

TAC Access Control System.

talk

Talk.

tftp

Trivial File Transfer Protocol.

time

Time.

who

Who service.

xdmcp

X Display Manager Control Protocol.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

flow-label

IPv6 Flow-label.

<0-1048575>

IPv6 Flow-label value.

fragments

Check non-initial fragments.

vlan

Match packets with given VLAN identifier.

<1-4094>

Enter VLAN identifier.

inner-vlan

Match packets with given inner VLAN identifier.

<1-4094>

Enter inner-VLAN identifier.

redirect-to-port

Redirect the packet (in-direction only)

IFNAME

Interface name to which packet to be redirected

Command Mode

IPv6 access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#ipv6 access-list mylist

(config-ipv6-acl)#deny udp any eq tftp

(config-ipv6-acl)#deny tcp fd22:bf66:78a4:10a2::/64 fdf2:860a:746a:e49c::/64 eq ssh

line vty

Use this command to move or change to ALL LINE VTY mode.

Command Syntax

line vty

Parameters

Command Mode

Configure mode

Applicability

This command was introduced from OcNOS version 1.3.8

Examples

The following example shows entering all line mode (note the change in the prompt).

#configure terminal

(config)#line vty

(config-all-line)#exit

mac access-group

Use this command to attach a MAC access list to an interface to filter incoming packets.

When you attach an access list to a VLAN interface or LAG interface as well as to a physical interface that is a member of that LAG and/or VLAN interface, the priority order is:

1. VLAN interface

2. LAG interface

3. Physical interface

The time-range parameter is optional. If used, the access-group is tied to the timer specified.

To delete the access-group, use the no form of this command without a time-range.

Note: An access-group on egress access-group on egress direction uses the TCAM group used by the QoS output service policy. Therefore, actions are unpredictable when conflicting matches are configured on same interface. IP Infusion Inc. recommends avoiding such a configuration. Otherwise, you need to configure the priority (in QoS) or the sequence number (in ACL) carefully to handle such cases.

Command Syntax

mac access-group NAME (in|out) (in|out) (time-range TR_NAME|)

no mac access-group NAME (in|out) (time-range TR_NAME|)

Parameters

NAME

Access list name.

Filter incoming packets.

out

Filter outgoing packets

TR_NAME

Time range name set with the time-range command

Command Mode

Interface mode

Applicability

This command was introduced before OcNOS version 1.3. The time-range parameter was added in OcNOS-SP version 5.0.

Examples

#configure terminal

(config)#mac access-list mylist

(config-mac-acl)#permit any any

(config-mac-acl)#exit

(config)#hardware-profile filter ingress-l2-ext enable

(config)#interface xe3

(config-if)#mac access-group mylist in

(config-if)#exit

(config)#interface xe3

(config-if)#mac access-group mylist in time-range TIMER1

(config-if)#exit

(config)#interface xe3

(config-if)#no mac access-group mylist in time-range TIMER1

(config-if)#exit

(config)#interface xe3

(config-if)#no mac access-group mylist in

(config-if)#exit

mac access-list

Use this command to define a MAC access control list (ACL) that determines whether to accept or drop an incoming packet based on specifications configured under the ACL. An ACL is made up of one or more ACL specifications.

The device stops checking the specifications after a match occurs.

There is an implied deny specification for traffic that is not permitted. Implied specification can be updated to permit if the use-case is to deny a certain set of traffic.

Use the no form of this command to remove the ACL.

Command Syntax

mac access-list NAME

no mac access-list NAME

Parameters

NAME

Access-list name.

Command Mode

Configure mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#mac access-list mac-acl-01

(config-mac-acl)#exit

mac access-list default

Use this command to modify the default rule action of access-list. Default rule is applicable only when access-list is attached to interface. Default rule will have the lowest priority and only the packets not matching any of the user defined rules match default rule.

Command Syntax

default (deny-all|permit-all) (log|) (sample|)

Parameters

deny-all

Drop all packets.

permit-all

Accept all packets.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

Command Mode

MAC access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#mac access-list mac-acl-01

(config-mac-acl)#default permit-all sample

mac access-list filter

Use this command to define an access control entry (ACE) in a MAC access control list (ACL) that determines whether to permit or deny packets with the given source and destination MAC, ethertype, CoS, and VLAN identifiers.

Use the no form of this command to remove an ACL specification. ACL specification can be removed using the sequence number as well.

Note: Configuring same filter again with change of sequence number or change of action will result in update of sequence number or filter action.

Command Syntax

no (<1-268435453>)

Parameters

deny

Drop the packet.

permit

Accept the packet.

<1-268435453>

IPv4 ACL sequence number.

any

Source/Destination any.

XX-XX-XX-XX-XX-XX

Source/Destination MAC address (Option 1).

XX:XX:XX:XX:XX:XX

Source/Destination MAC address (Option 2).

XXXX.XXXX.XXXX

Source/Destination MAC address (Option 3).

XX-XX-XX-XX-XX-XX

Source/Destination wildcard (Option1).

XX:XX:XX:XX:XX:XX

Source/Destination wildcard (Option2).

XXXX.XXXX.XXXX

Source/Destination wildcard (Option3).

host

A single source/destination host.

aarp

Ethertype - 0x80f3.

appletalk

Ethertype - 0x809b.

decnet-iv

Ethertype - 0x6003.

diagnostic

Ethertype - 0x6005.

etype-6000

Ethertype - 0x6000.

etype-8042

Ethertype - 0x8042.

ip4

Ethertype - 0x0800.

ip6

Ethertype - 0x86dd.

mpls

Ethertype - 0x8847.

lat

Ethertype - 0x6004.

lavc-sca

Ethertype - 0x6007.

mop-console

Ethertype - 0x6002.

mop-dump

Ethertype - 0x6001.

vines-echo

Ethertype - 0x0baf.

WORD

Any Ethertype value.

cos <0-7>

Cos value.

vlan <1-4094>

VLAN identifier.

inner-vlan <1-4094>

Inner-VLAN identifier.

log

Log the packets matching the filter (in-direction only).

sample

Sample the packets matching the filter (in-direction only).

Command Mode

MAC access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#mac access-list mac-acl-01

(config-mac-acl)#permit 0000.1234.1234 0000.0000.0000 any sample

mac access-list remark

Use this command to add a description to an MAC access control list (ACL).

Use the no form of this command to remove an ACL description.

Command Syntax

remark LINE

no remark

Parameters

LINE

ACL description up to 100 characters.

Command Mode

MAC access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#mac access-list mylist

(config-mac-acl)#remark Permit the inside admin address

mac access-list resequence

Use this command to modify the sequence numbers of MAC access list specifications.

Note: Use a non-overlapping sequence space for new sequence number sets to avoid possible unexpected rule matches during transition.

Note: Re-sequencing an ACL attached to a management interface clears the ACL counters associated to it.

Command Syntax

resequence <1-268435453> INCREMENT

Parameters

<1-268435453>

Starting sequence number.

INCREMENT

Sequence number increment steps.

Command Mode

MAC access-list mode

Applicability

This command was introduced before OcNOS version 1.3.

Examples

#configure terminal

(config)#mac access-list mylist

(config-mac-acl)#resequence 15 15

show access-lists

Use this command to display access lists.

Command Syntax

show access-lists (NAME|) (expanded|summary|)

Parameters

NAME

Access-list name.

expanded

Expanded access-list.

summary

Summary of access-list.

Command Mode

Privileged Exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Example

#show access-lists expanded

IP access list Iprule1

11 permit ip 30.0.0.1 0.0.0.255 172.124.0.2 0.0.0.255

default deny-all

MAC access list Macrule1

10 permit host 0000.1234.1234 any

default deny-all

IPv6 access list ipv6-acl-01

10 deny ahp 3ffe::/64 4ffe::/64

default deny-all

#show access-lists summary

IPV4 ACL Iprule1

statistics enabled

Total ACEs Configured: 1

Configured on interfaces:

xe3/1 - egress (Router ACL)

Active on interfaces:

xe1/3 - ingress (Router ACL)

MAC ACL Macrule1

statistics enabled

Total ACEs Configured: 0

Configured on interfaces:

Active on interfaces:

IPV6 ACL ipv6-acl-01

statistics enabled

Total ACEs Configured: 2

Configured on interfaces:

xe7/1 - ingress (Router ACL)

Active on interfaces:

show access-list log-cache

Use this command to show the ACL logging table entries

Command Syntax

show access-lists log-cache

Parameters

None

Command Mode

Privileged Exec mode and Exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Example

#show access-lists log-cache

2016 Oct 26 12:08:37:xe1/1: 0000.0100.0a00 -> 0000.0100.0b00, ethertype IP (0x800), proto tcp, vlan 2, 0.0.0.0:0 -> 0.0.0.0:0 ...suppressed 11 times

2016 Oct 26 12:07:51:xe1/1: 0000.0100.0a00 -> 0000.0100.0b00, ethertype IP (0x800), proto 255, vlan 2, 0.0.0.0 -> 0.0.0.0 ...suppressed 10 times

show arp access-lists

Use this command to display ARP access lists.

Command Syntax

show arp access-lists (NAME|) (expanded|summary|)

Parameters

NAME

ARP access-list name.

expanded

Expanded access-list.

summary

Access-list summary.

Command Mode

Privileged Exec mode and Exec mode

Applicability

This command was introduced in OcNOS version 1.3.6.

Example

#show arp access-lists

ARP access list arp1

remark "arp access-list created"

10 permit ip any mac any

show ip access-lists

Use this command to display IP access list

Command Syntax

show ip access-lists (NAME|) (expanded|summary|)

Parameters

NAME

Access-list name.

expanded

Expanded access-list.

summary

Summary of access-list.

Command Mode

Exec mode and Privileged Exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Example

#show ip access-lists

IP access list Iprule2

11 permit ip 30.0.0.1 0.0.0.255 172.124.0.2 0.0.0.255

12 deny ip 30.0.0.2 0.0.0.255 182.124.0.3/24

default deny-all

#show ip access-lists summary

IPV4 ACL Iprule3

statistics enabled

Total ACEs Configured: 4

Configured on interfaces:

sa1 - ingress (Port ACL)

sa3 - ingress (Router ACL)

sa8 - ingress (Port ACL)

vlan1.3 - ingress (Router ACL)

xe1/1 - ingress (Port ACL)

xe1/2 - ingress (Router ACL)

xe1/3 - ingress (Router ACL)

xe3/1 - egress (Router ACL)

Active on interfaces:

sa1 - ingress (Port ACL)

xe1/1 - ingress (Port ACL)

xe1/2 - ingress (Router ACL)

xe1/3 - ingress (Router ACL)

show ipv6 access-lists

Use this command to display IPv6 access lists.

Command Syntax

show ipv6 access-lists (NAME|) (expanded|summary|)

Parameters

NAME

Access-list name.

expanded

Expanded access-list.

summary

Summary of access-list.

Command Mode

Privileged Exec mode and Exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Example

#show ipv6 access-lists

IPv6 access list ipv6-acl-01

10 deny ahp 3ffe::/64 4ffe::/64

20 permit ahp 78fe::1/48 68fe::1/48

30 permit ahp 3333::1/64 4444::1/48 fragments

40 permit ahp 5555::1/64 4444::1/48 dscp af23

default deny-all

#show ipv6 access-lists summary

IPV6 ACL ipv6-acl-01

statistics enabled

Total ACEs Configured: 4

Configured on interfaces:

sa3 - ingress (Router ACL)

vlan1.3 - ingress (Router ACL)

xe1/1 - ingress (Port ACL)

xe1/2 - ingress (Router ACL)

xe1/3 - ingress (Router ACL)

Active on interfaces:

xe1/1 - ingress (Port ACL)

xe1/2 - ingress (Router ACL)

xe1/3 - ingress (Router ACL)

show mac access-lists

Use this command to display MAC access lists.

Command Syntax

show mac access-lists (NAME|) (expanded|summary|)

Parameters

NAME

Access-list name.

expanded

Expanded access-list.

summary

Summary of access-list.

Command Mode

Privileged exec mode and exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Example

#show mac access-lists

MAC access list Macrule2

default deny-all

MAC access list Macrule3

10 permit host 0000.1234.1234 any

20 deny host 1111.1111.AAAA any 65535

30 permit host 2222.2222.AAAA any 65535

40 permit 0000.3333.3333 0000.0000.FFFF 4444.4444.4444 0000.0000.FFFF

default deny-all [match=1126931077]

#show mac access-lists summary

MAC ACL Macrule3

statistics enabled

Total ACEs Configured: 4

Configured on interfaces:

sa3 - ingress (Router ACL)

sa8 - ingress (Port ACL)

vlan1.3 - ingress (Router ACL)

xe1/1 - ingress (Port ACL)

xe1/2 - ingress (Router ACL)

xe1/3 - ingress (Router ACL)

Active on interfaces:

xe1/1 - ingress (Port ACL)

xe1/2 - ingress (Router ACL)

xe1/3 - ingress (Router ACL)

show running-config aclmgr

Use this command to display the entire access list configurations along with the attachment to interfaces.

Command Syntax

show running-config aclmgr (all|)

Parameters

all

Show running configuration with defaults.

Command Mode

Exec mode and privileged exec mode

Applicability

This command was introduced before OcNOS version 1.3.

Example

#show running-config aclmgr

ip access-list ip-acl-01

11 permit ip 30.0.0.1 0.0.0.255 172.124.0.2 0.0.0.255

12 deny ip 30.0.0.2 0.0.0.255 182.124.0.3/24

mac access-list mac-acl-01

10 permit host 0000.1234.1234 any

20 permit host 0000.1111.AAAA any ipv4 cos 3 vlan 3

ipv6 access-list ipv6-acl-01

10 deny ipv6 3ffe::/64 4ffe::/64 dscp af43

20 permit ipv6 78fe::/64 68fe::/64 dscp cs3

interface xe1/1

ip access-group ip-acl-01 in

show running-config access-list

Use this command to show the running system status and configuration details for MAC and IP access lists.

Command Syntax

show running-config access-list

Parameters

None

Command Mode

Privileged exec mode, configure mode, and route-map mode

Applicability

This command was introduced before OcNOS version 1.3.

Example

#show running-config access-list

ip access-list abd

10 deny any any any

mac access-list abc

remark test

10 deny any any

show running-config ipv6 access-list

Use this command to show the running system status and configuration details for IPv6 access lists.

Command Syntax

show running-config ipv6 access-list

Parameters

None

Command Mode

Privileged exec mode, configure mode, and route-map mode

Applicability

This command was introduced before OcNOS version 1.3.

Example

#show running-config ipv6 access-list

ipv6 access-list test

10 permit any any any