Configuring ISIS Segment Routing
This chapter shows how to configure segment routing using ISIS. ISIS uses ISIS-TE TLVs to advertise any additional attributes associated with prefix by adding new TLVs or sub-TLVs to the existing ISIS-TE TLVs.
These segments are converted to MPLS labels and installed in the FTN/ILM and forwarding tables.
Topology
In Figure 2-2:
• “L1” means ISIS routers in Level-1
• “L2” means ISIS routers in Level-2
• “L1/L2” means ISIS routers in both Level-1 and Level-2
You can configure a prefix SID on any router directly attached to that network prefix.
ISIS Segment Routing Topology
Note:
1. You must ensure that prefix SIDs are unique globally.
2. You can use the pure L1 or L2 routers throughout your SR domain.
3. Redistribution from L1 to L2 and vice-versa is not supported for SR in this release.
PE1
PE1#configure terminal | Enter configure mode. |
PE1(config)#interface lo | Enter interface mode. |
PE1(config-if)#ip address 10.0.1.11/32 secondary | Configure the IP address of the interface. |
PE1(config-if)#ip router isis isis1 | Make the interface part of the router isis isis isis1 instance. |
PE1(config-if)#prefix-sid index 100 | Configure prefix sid index value. |
PE1(config-if)#exit | Exit interface mode. |
PE1(config)#commit | Commit candidate configuration to the running configuration |
PE1(config)#interface eth2 | Enter interface mode. |
PE1(config-if)#ip address 10.11.1.1/30 | Configure the IP address of the interface. |
PE1(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
PE1(config-if)#label-switching | Enable label switching. |
PE1(config-if)#commit | Commit candidate configuration to the running configuration |
PE1(config-if)#exit | Exit interface mode. |
PE1(config)#interface eth3 | Enter interface mode. |
PE1(config-if)#ip address 10.11.2.2/30 | Configure the IP address of the interface. |
PE1(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
PE1(config-if)#label-switching | Enable label switching. |
PE1(config-if)#commit | Commit candidate configuration to the running configuration |
PE1(config-if)#exit | Exit interface mode. |
PE1(config)#router isis isis1 | Set the routing process ID . |
PE1(config-router)#metric-style wide | Configure metric style as wide. |
PE1(config-router)#is-type level-1-2 | Configure is-type with level-1-2. |
PE1(config-router)#net 49.0000.0100.0000.1011.00 | Configure Network entity title (NET). |
PE1(config-router)#mpls traffic-eng level-1 | Enable MPLS Traffic Engineering as level-1. |
PE1(config-router)#mpls traffic-eng level-2 | Enable MPLS Traffic Engineering as level-2. |
PE1(config-router)# dynamic-hostname | Enable dynamic-hostname under ISIS isis1 process. |
PE1(config-router)# isis segment-routing global block 16000 23999 | Enable SRGB under ISIS isis1 process. |
PE1(config-router)#segment-routing mpls | Enable segment routing under router process. |
PE1(config-router)#commit | Commit candidate configuration to the running configuration |
PE1(config-router)#exit | Exit router mode. |
P1
P1#configure terminal | Enter configure mode. |
P1(config)#interface lo | Enter interface mode. |
P1(config-if)#ip address 10.0.1.1/32 secondary | Configure the IP address of the interface. |
P1(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
P1(config-if)#prefix-sid index 200 | Configure prefix sid index value. |
P1(config-if)#commit | Commit candidate configuration to the running configuration |
P1(config-if)#exit | Exit interface mode. |
P1(config)#interface eth2 | Enter interface mode. |
P1(config-if)#ip address 10.11.1.2/30 | Configure the IP address of the interface. |
P1(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
P1(config-if)#label-switching | Enable label switching. |
P1(config-if)#commit | Commit candidate configuration to the running configuration |
P1(config-if)#exit | Exit interface mode. |
P1(config)#interface eth1 | Enter interface mode. |
P1(config-if)#ip address 10.1.2.1/30 | Configure the IP address of the interface. |
P1(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
P1(config-if)#label-switching | Enable label switching. |
P1(config-if)#commit | Commit candidate configuration to the running configuration |
P1(config-if)#exit | Exit interface mode. |
P1(config)#interface eth4 | Enter interface mode. |
P1(config-if)#ip address 10.33.1.2/30 | Configure the IP address of the interface. |
P1(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
P1(config-if)#label-switching | Enable label switching. |
P1(config-if)#exit | Exit interface mode. |
P1(config)#router isis isis1 | Set the routing process ID . |
P1(config-router)#metric-style wide | Configure metric style as wide. |
P1(config-router)#is-type level-1-2 | Configure is-type with level-1-2. |
P1(config-router)#net 49.0000.0100.0000.1001.00 | Configure Network entity title (NET). |
P1(config-router)#mpls traffic-eng level-1 | Enable MPLS Traffic Engineering as level-1. |
P1(config-router)#mpls traffic-eng level-2 | Enable MPLS Traffic Engineering as level-2. |
P1(config-router)#dynamic-hostname | Enable dynamic-hostname under ISIS isis1 process. |
P1(config-router)# isis segment- routing global block 17000 23500 | Enable SRGB under ISIS isis1 process. |
P1(config-router)#segment-routing mpls | Enable segment routing under router process. |
P1(config-router)#commit | Commit candidate configuration to the running configuration |
P1(config-router)#exit | Exit router mode. |
P2
P2#configure terminal | Enter configure mode. |
P2(config)#interface lo | Enter interface mode. |
P2(config-if)#ip address 10.0.1.2/32 secondary | Configure the IP address of the interface. |
P2(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
P2(config-if)#prefix-sid index 300 no-php | Configure prefix sid index value with no php. |
P2(config-if)#commit | Commit candidate configuration to the running configuration |
P2(config-if)#exit | Exit interface mode. |
P2(config)#interface eth3 | Enter interface mode. |
P2(config-if)#ip address 10.1.2.2/30 | Configure the IP address of the interface. |
P2(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
P2(config-if)#label-switching | Enable label switching. |
P2(config-if)#exit | Exit interface mode. |
P2(config)#interface eth1 | Enter interface mode. |
P2(config-if)#ip address 10.1.2.2/30 | Configure the IP address of the interface. |
P2(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
P2(config-if)#label-switching | Enable label switching. |
P2(config-if)#commit | Commit candidate configuration to the running configuration. |
P2(config-if)#exit | Exit interface mode. |
P2(config)#interface eth4 | Enter interface mode. |
P2(config-if)#ip address 10.44.2.2/30 | Configure the IP address of the interface. |
P2(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
P2(config-if)#label-switching | Enable label switching. |
P2(config-if)#commit | Commit candidate configuration to the running configuration |
P2(config-if)#exit | Exit interface mode. |
P2(config)#router isis isis1 | Set the routing process ID . |
P2(config-router)#metric-style wide | Configure metric style as wide. |
P2(config-router)#is-type level-1-2 | Configure is-type with level-1-2. |
P2(config-router)#net 49.0000.0100.0000.1002.00 | Configure Network entity title (NET). |
P2(config-router)#mpls traffic-eng level-1 | Enable MPLS Traffic Engineering as level-1. |
P2(config-router)#mpls traffic-eng level-2 | Enable MPLS Traffic Engineering as level-2 as well. |
P2 (config-router)#dynamic-hostname | Enable dynamic-hostname under ISIS isis1 process. |
P2(config-router)#isis segment-routing global block 16500 22500 | Enable SRGB under ISIS isis1 process. |
P2(config-router)#segment-routing mpls | Enable segment routing under router process. |
P2(config-router)#commit | Commit candidate configuration to the running configuration |
P2(config-router)#exit | Exit router mode. |
PE3
PE3#configure terminal | Enter configure mode. |
PE3(config)#interface lo | Enter interface mode. |
PE3(config-if)#ip address 10.0.1.33/32 secondary | Configure the IP address of the interface. |
PE3(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
PE3(config-if)#prefix-sid index 500 | Configure prefix sid index value. |
PE3(config-if)#commit | Commit candidate configuration to the running configuration |
PE3(config-if)#exit | Exit interface mode. |
PE3(config)#interface eth1 | Enter interface mode. |
PE3(config-if)#ip address 10.33.44.1/30 | Configure the IP address of the interface. |
PE3(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
PE3(config-if)#label-switching | Enable label switching. |
PE3(config-if)#commit | Commit candidate configuration to the running configuration |
PE3(config-if)#exit | Exit interface mode. |
PE3(config)#interface eth4 | Enter interface mode. |
PE3(config-if)#ip address 10.33.1.1/30 | Configure the IP address of the interface. |
PE3(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
PE3(config-if)#label-switching | Enable label switching. |
PE3(config-if)#commit | Commit candidate configuration to the running configuration |
PE3(config-if)#exit | Exit interface mode. |
PE3(config)#router isis isis1 | Set the routing process ID . |
PE3(config-router)#metric-style wide | Configure metric style as wide. |
PE3(config-router)#is-type level-1-2 | Configure is-type with level-1-2. |
PE3(config-router)#net 49.0000.0100.0000.1033.00 | Configure Network entity title (NET). |
PE3(config-router)#mpls traffic-eng level-1 | Enable MPLS Traffic Engineering as level-1. |
PE3(config-router)#mpls traffic-eng level-2 | Enable MPLS Traffic Engineering as level- 2 as well. |
PE3(config-router)#dynamic-hostname | Enable dynamic-hostname under ISIS isis1 process |
PE3(config-router)# isis segment- routing global block 17500 22000 | Enable SRGB under ISIS isis1 process. |
PE3(config-router)#segment-routing mpls | Enable segment routing under router process. |
PE3(config-router)#commit | Commit candidate configuration to the running configuration |
PE3(config-router)#exit | Exit router mode. |
PE4
PE4#configure terminal | Enter configure mode. |
PE4(config)#interface lo | Enter interface mode. |
PE4(config-if)#ip address 10.0.1.44/32 secondary | Configure the IP address of the interface. |
PE4(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
PE4(config-if)#prefix-sid index 600 no-php | Configure prefix sid index value with no php. |
PE4(config-if)#exit | Exit interface mode. |
PE4(config)#commit | Commit candidate configuration to the running configuration |
PE4(config)#interface eth4 | Enter interface mode. |
PE4(config-if)#ip address 10.44.2.1/30 | Configure the IP address of the interface. |
PE4(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
PE4(config-if)#label-switching | Enable label switching. |
PE4(config-if)#commit | Commit candidate configuration to the running configuration |
PE4(config-if)#exit | Exit interface mode. |
PE4(config)#interface eth1 | Enter interface mode. |
PE4(config-if)#ip address 10.33.44.2/30 | Configure the IP address of the interface. |
PE4(config-if)#ip router isis isis1 | Make the interface part of the router isis isis1 instance. |
PE4(config-if)#label-switching | Enable label switching. |
PE4(config-if)#commit | Commit candidate configuration to the running configuration |
PE4(config-if)#exit | Exit interface mode. |
PE4(config)#router isis isis1 | Set the routing process ID . |
PE4(config-router)#metric-style wide | Configure metric style as wide. |
PE4(config-router)#net 49.0000.0100.0000.1044.00 | Configure Network entity title (NET). |
PE4(config-router)#mpls traffic-eng level-1 | Enable MPLS Traffic Engineering as level-1. |
PE4(config-router)#mpls traffic-eng level-2 | Enable MPLS Traffic Engineering as level-2. |
PE4(config-router)#dynamic-hostname | Enable dynamic-hostname under ISIS isis1 process. |
PE4(config-router)# isis segment- routing global block 18000 23999 | Enable SRGB under ISIS isis1 process. |
PE4(config-router)#segment-routing mpls | Enable segment routing under router process. |
PE4(config-if)#commit | Commit candidate configuration to the running configuration |
PE4(config-router)#exit | Exit router mode. |
Note: By default, PHP is enabled, to see all the labels in MPLS forwarding and ILM table we have enabled with non-php option.
Validation
Validation 1
Verify ISIS neighbor adjacency between routers.
PE1#sh clns neighbors
Total number of L1 adjacencies: 2
Total number of L2 adjacencies: 2
Total number of adjacencies: 4
Tag isis1: VRF : default
System Id Interface SNPA State Holdtime Type Protocol
P1 eth2 5254.008b.368d Up 8 L1 IS-IS
Up 8 L2 IS-IS
P2 eth3 5254.0098.900b Up 23 L1 IS-IS
Up 23 L2 IS-IS
P1#show clns neighbors
Total number of L1 adjacencies: 3
Total number of L2 adjacencies: 3
Total number of adjacencies: 6
Tag isis1: VRF : default
System Id Interface SNPA State Holdtime Type Protocol
P2 eth1 5254.00de.ca03 Up 5 L1 IS-IS
Up 5 L2 IS-IS
PE1 eth2 5254.0060.8a75 Up 27 L1 IS-IS
Up 27 L2 IS-IS
PE3 eth4 5254.0085.7e32 Up 5 L1 IS-IS
Up 5 L2 IS-IS
P2#show clns neighbors
Total number of L1 adjacencies: 3
Total number of L2 adjacencies: 3
Total number of adjacencies: 6
Tag isis1: VRF : default
System Id Interface SNPA State Holdtime Type Protocol
P1 eth1 5254.00a6.9153 Up 28 L1 IS-IS
Up 28 L2 IS-IS
PE1 eth3 5254.00ac.d346 Up 6 L1 IS-IS
Up 6 L2 IS-IS
PE4 eth4 5254.00c8.98db Up 6 L1 IS-IS
Up 6 L2 IS-IS
PE3#show clns neighbors
Total number of L1 adjacencies: 2
Total number of L2 adjacencies: 2
Total number of adjacencies: 4
Tag isis1: VRF : default
System Id Interface SNPA State Holdtime Type Protocol
PE4 eth1 5254.0007.09e5 Up 26 L1 IS-IS
Up 26 L2 IS-IS
P1 eth4 5254.000d.673d Up 26 L1 IS-IS
Up 26 L2 IS-IS
PE4#show clns neighbors
Total number of L1 adjacencies: 2
Total number of L2 adjacencies: 2
Total number of adjacencies: 4
Tag isis1: VRF : default
System Id Interface SNPA State Holdtime Type Protocol
PE3 eth1 5254.00d0.4baf Up 8 L1 IS-IS
Up 8 L2 IS-IS
P2 eth4 5254.0011.6e77 Up 20 L1 IS-IS
Up 20 L2 IS-IS
The command output below displays the details of routers configured with segment routing.
P1#show isis segment-routing capability
Tag isis1 Segment-Routing:
-----------------------------------------------------
Advertisement Router Capability :10.0.1.11
Algorithm0 :0
SRMS Preference :0
Total SID'S Supported :8000
SID Range List Count :1
SID's Range :16000 - 23999
-----------------------------------------------------
Advertisement Router Capability :10.0.1.1
Algorithm0 :0
SRMS Preference :0
Total SID'S Supported :6501
SID Range List Count :1
SID's Range :17000 - 23500
-----------------------------------------------------
Advertisement Router Capability :10.0.1.33
Algorithm0 :0
SRMS Preference :0
Total SID'S Supported :4501
SID Range List Count :1
SID's Range :17500 - 22000
-----------------------------------------------------
Advertisement Router Capability :10.0.1.44
Algorithm0 :0
SRMS Preference :0
Total SID'S Supported :6000
SID Range List Count :1
SID's Range :18000 - 23999
-----------------------------------------------------
Advertisement Router Capability :10.0.1.2
Algorithm0 :0
SRMS Preference :0
Total SID'S Supported :6001
SID Range List Count :1
SID's Range :16500 - 22500
-----------------------------------------------------
Validation 3
Verify that segment routing information is present in ISIS database.
P1#show isis database verbose
Tag isis1: VRF : default
IS-IS Level-1 Link State Database:
LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL
P1.00-00 * 0x00000015 0x0E94 1137 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: P1
IP Address: 10.0.1.1
Router ID: 10.0.1.1
Router Cap: 10.0.1.1
SRGB Range: 6501 SRGB Base SID: 17000 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended PE3.03
IPv4 Interface Address: 10.33.1.2
Neighbor IP Address: 10.33.1.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1033 LAN Adjacency SID: 24320 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended P1.03
IPv4 Interface Address: 10.11.1.2
Neighbor IP Address: 10.11.1.2
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1011 LAN Adjacency SID: 24321 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended P2.02
IPv4 Interface Address: 10.1.2.1
Neighbor IP Address: 10.1.2.2
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1002 LAN Adjacency SID: 24322 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.1/32
Prefix-SID: index 200 R:0 N:1 P:0 E:0 V:0 L:0
Metric: 10 IP-Extended 10.1.2.0/30
Metric: 10 IP-Extended 10.11.1.0/30
Metric: 10 IP-Extended 10.33.1.0/30
P1.03-00 * 0x0000000D 0xBFBA 1133 0/0/0
Metric: 0 IS-Extended P1.00
Metric: 0 IS-Extended PE1.00
P2.00-00 0x00000015 0x70EC 1136 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: P2
IP Address: 10.0.1.2
Router ID: 10.0.1.2
Router Cap: 10.0.1.2
SRGB Range: 6001 SRGB Base SID: 16500 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended P2.02
IPv4 Interface Address: 10.1.2.2
Neighbor IP Address: 10.1.2.2
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1001 LAN Adjacency SID: 24320 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended PE1.04
IPv4 Interface Address: 10.11.2.2
Neighbor IP Address: 10.11.2.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1011 LAN Adjacency SID: 24321 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended PE4.03
IPv4 Interface Address: 10.44.2.2
Neighbor IP Address: 10.44.2.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1044 LAN Adjacency SID: 24322 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.2/32
Prefix-SID: index 300 R:0 N:1 P:1 E:0 V:0 L:0
Metric: 10 IP-Extended 10.1.2.0/30
Metric: 10 IP-Extended 10.1.24.0/24
Metric: 10 IP-Extended 10.11.2.0/30
Metric: 10 IP-Extended 10.44.2.0/30
P2.02-00 0x0000000D 0x8603 1132 0/0/0
Metric: 0 IS-Extended P2.00
Metric: 0 IS-Extended P1.00
PE1.00-00 0x00000013 0xE7E5 1136 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: PE1
IP Address: 10.0.1.11
Router ID: 10.0.1.11
Router Cap: 10.0.1.11
SRGB Range: 8000 SRGB Base SID: 16000 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended PE1.04
IPv4 Interface Address: 10.11.2.1
Neighbor IP Address: 10.11.2.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1002 LAN Adjacency SID: 26241 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended P1.03
IPv4 Interface Address: 10.11.1.1
Neighbor IP Address: 10.11.1.2
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1001 LAN Adjacency SID: 26240 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.11/32
Prefix-SID: index 100 R:0 N:1 P:0 E:0 V:0 L:0
Metric: 10 IP-Extended 10.11.1.0/30
Metric: 10 IP-Extended 10.11.2.0/30
PE1.04-00 0x0000000D 0x9BCC 1132 0/0/0
Metric: 0 IS-Extended PE1.00
Metric: 0 IS-Extended P2.00
PE3.00-00 0x00000013 0x476C 1136 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: PE3
IP Address: 10.0.1.33
Router ID: 10.0.1.33
Router Cap: 10.0.1.33
SRGB Range: 4501 SRGB Base SID: 17500 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended PE3.02
IPv4 Interface Address: 10.33.44.1
Neighbor IP Address: 10.33.44.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1044 LAN Adjacency SID: 24960 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended PE3.03
IPv4 Interface Address: 10.33.1.1
Neighbor IP Address: 10.33.1.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1001 LAN Adjacency SID: 24961 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.33/32
Prefix-SID: index 500 R:0 N:1 P:0 E:0 V:0 L:0
Metric: 10 IP-Extended 10.33.44.0/30
Metric: 10 IP-Extended 10.33.1.0/30
Metric: 10 IP-Extended 10.1.45.0/24
PE3.02-00 0x0000000C 0xFAE9 1132 0/0/0
Metric: 0 IS-Extended PE3.00
Metric: 0 IS-Extended PE4.00
PE3.03-00 0x0000000D 0xB075 1132 0/0/0
Metric: 0 IS-Extended PE3.00
Metric: 0 IS-Extended P1.00
PE4.00-00 0x00000012 0xD15B 1136 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: PE4
IP Address: 10.0.1.44
Router ID: 10.0.1.44
Router Cap: 10.0.1.44
SRGB Range: 6000 SRGB Base SID: 18000 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended PE3.02
IPv4 Interface Address: 10.33.44.2
Neighbor IP Address: 10.33.44.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1033 LAN Adjacency SID: 25600 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended PE4.03
IPv4 Interface Address: 10.44.2.1
Neighbor IP Address: 10.44.2.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1002 LAN Adjacency SID: 25601 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.44/32
Prefix-SID: index 600 R:0 N:1 P:1 E:0 V:0 L:0
Metric: 10 IP-Extended 10.33.44.0/30
Metric: 10 IP-Extended 10.44.2.0/30
Metric: 10 IP-Extended 10.1.36.0/24
PE4.03-00 0x0000000C 0xD72C 1132 0/0/0
Metric: 0 IS-Extended PE4.00
Metric: 0 IS-Extended P2.00
IS-IS Level-2 Link State Database:
LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL
P1.00-00 * 0x0000001F 0xBE3D 1148 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: P1
IP Address: 10.0.1.1
Router ID: 10.0.1.1
Router Cap: 10.0.1.1
SRGB Range: 6501 SRGB Base SID: 17000 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended PE3.03
IPv4 Interface Address: 10.33.1.2
Neighbor IP Address: 10.33.1.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1033 LAN Adjacency SID: 24320 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended P1.03
IPv4 Interface Address: 10.11.1.2
Neighbor IP Address: 10.11.1.2
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1011 LAN Adjacency SID: 24321 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended P2.02
IPv4 Interface Address: 10.1.2.1
Neighbor IP Address: 10.1.2.2
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1002 LAN Adjacency SID: 24322 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.1/32
Prefix-SID: index 200 R:0 N:1 P:0 E:0 V:0 L:0
Metric: 10 IP-Extended 10.1.2.0/30
Metric: 10 IP-Extended 10.11.1.0/30
Metric: 10 IP-Extended 10.33.1.0/30
Metric: 20 IP-Extended 10.0.1.2/32
Prefix-SID: index 300 R:1 N:0 P:1 E:0 V:0 L:0
Metric: 20 IP-Extended 10.0.1.33/32
Prefix-SID: index 500 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 20 IP-Extended 10.1.24.0/24
Metric: 20 IP-Extended 10.1.45.0/24
Metric: 20 IP-Extended 10.11.2.0/30
Metric: 20 IP-Extended 10.33.44.0/30
Metric: 20 IP-Extended 10.44.2.0/30
Metric: 20 IP-Extended 10.0.1.11/32
Prefix-SID: index 100 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 30 IP-Extended 10.0.1.44/32
Prefix-SID: index 600 R:1 N:0 P:1 E:0 V:0 L:0
Metric: 30 IP-Extended 10.1.36.0/24
P1.03-00 * 0x0000000C 0xC1B9 1133 0/0/0
Metric: 0 IS-Extended P1.00
Metric: 0 IS-Extended PE1.00
P2.00-00 0x00000020 0xB0EE 1147 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: P2
IP Address: 10.0.1.2
Router ID: 10.0.1.2
Router Cap: 10.0.1.2
SRGB Range: 6001 SRGB Base SID: 16500 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended P2.02
IPv4 Interface Address: 10.1.2.2
Neighbor IP Address: 10.1.2.2
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1001 LAN Adjacency SID: 24320 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended PE1.04
IPv4 Interface Address: 10.11.2.2
Neighbor IP Address: 10.11.2.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1011 LAN Adjacency SID: 24321 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended PE4.03
IPv4 Interface Address: 10.44.2.2
Neighbor IP Address: 10.44.2.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1044 LAN Adjacency SID: 24322 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.2/32
Prefix-SID: index 300 R:0 N:1 P:1 E:0 V:0 L:0
Metric: 10 IP-Extended 10.1.2.0/30
Metric: 10 IP-Extended 10.1.24.0/24
Metric: 10 IP-Extended 10.11.2.0/30
Metric: 10 IP-Extended 10.44.2.0/30
Metric: 20 IP-Extended 10.0.1.11/32
Prefix-SID: index 100 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 20 IP-Extended 10.0.1.44/32
Prefix-SID: index 600 R:1 N:0 P:1 E:0 V:0 L:0
Metric: 20 IP-Extended 10.1.36.0/24
Metric: 20 IP-Extended 10.11.1.0/30
Metric: 20 IP-Extended 10.33.44.0/30
Metric: 20 IP-Extended 10.0.1.1/32
Prefix-SID: index 200 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 30 IP-Extended 10.0.1.33/32
Prefix-SID: index 500 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 30 IP-Extended 10.1.45.0/24
Metric: 20 IP-Extended 10.33.1.0/30
P2.02-00 0x0000000C 0x8802 1132 0/0/0
Metric: 0 IS-Extended P2.00
Metric: 0 IS-Extended P1.00
PE1.00-00 0x0000001E 0xD679 1147 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: PE1
IP Address: 10.0.1.11
Router ID: 10.0.1.11
Router Cap: 10.0.1.11
SRGB Range: 8000 SRGB Base SID: 16000 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended PE1.04
IPv4 Interface Address: 10.11.2.1
Neighbor IP Address: 10.11.2.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1002 LAN Adjacency SID: 26241 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended P1.03
IPv4 Interface Address: 10.11.1.1
Neighbor IP Address: 10.11.1.2
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1001 LAN Adjacency SID: 26240 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.11/32
Prefix-SID: index 100 R:0 N:1 P:0 E:0 V:0 L:0
Metric: 10 IP-Extended 10.11.1.0/30
Metric: 10 IP-Extended 10.11.2.0/30
Metric: 20 IP-Extended 10.0.1.1/32
Prefix-SID: index 200 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 20 IP-Extended 10.1.2.0/30
Metric: 20 IP-Extended 10.33.1.0/30
Metric: 20 IP-Extended 10.0.1.2/32
Prefix-SID: index 300 R:1 N:0 P:1 E:0 V:0 L:0
Metric: 30 IP-Extended 10.0.1.33/32
Prefix-SID: index 500 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 30 IP-Extended 10.0.1.44/32
Prefix-SID: index 600 R:1 N:0 P:1 E:0 V:0 L:0
Metric: 20 IP-Extended 10.1.24.0/24
Metric: 30 IP-Extended 10.1.36.0/24
Metric: 30 IP-Extended 10.1.45.0/24
Metric: 30 IP-Extended 10.33.44.0/30
Metric: 20 IP-Extended 10.44.2.0/30
PE1.04-00 0x0000000B 0x9FCA 1132 0/0/0
Metric: 0 IS-Extended PE1.00
Metric: 0 IS-Extended P2.00
PE3.00-00 0x0000001E 0xFAAF 1147 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: PE3
IP Address: 10.0.1.33
Router ID: 10.0.1.33
Router Cap: 10.0.1.33
SRGB Range: 4501 SRGB Base SID: 17500 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended PE3.02
IPv4 Interface Address: 10.33.44.1
Neighbor IP Address: 10.33.44.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1044 LAN Adjacency SID: 24960 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended PE3.03
IPv4 Interface Address: 10.33.1.1
Neighbor IP Address: 10.33.1.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1001 LAN Adjacency SID: 24961 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.33/32
Prefix-SID: index 500 R:0 N:1 P:0 E:0 V:0 L:0
Metric: 10 IP-Extended 10.33.44.0/30
Metric: 10 IP-Extended 10.33.1.0/30
Metric: 10 IP-Extended 10.1.45.0/24
Metric: 20 IP-Extended 10.0.1.1/32
Prefix-SID: index 200 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 30 IP-Extended 10.0.1.2/32
Prefix-SID: index 300 R:1 N:0 P:1 E:0 V:0 L:0
Metric: 30 IP-Extended 10.0.1.11/32
Prefix-SID: index 100 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 20 IP-Extended 10.0.1.44/32
Prefix-SID: index 600 R:1 N:0 P:1 E:0 V:0 L:0
Metric: 20 IP-Extended 10.1.2.0/30
Metric: 30 IP-Extended 10.1.24.0/24
Metric: 20 IP-Extended 10.1.36.0/24
Metric: 20 IP-Extended 10.11.1.0/30
Metric: 30 IP-Extended 10.11.2.0/30
Metric: 20 IP-Extended 10.44.2.0/30
PE3.02-00 0x0000000B 0xFCE8 1132 0/0/0
Metric: 0 IS-Extended PE3.00
Metric: 0 IS-Extended PE4.00
PE3.03-00 0x0000000C 0xB274 1132 0/0/0
Metric: 0 IS-Extended PE3.00
Metric: 0 IS-Extended P1.00
PE4.00-00 0x0000001F 0x7C42 1147 0/0/0
Area Address: 49.0000
NLPID: 0xCC
Hostname: PE4
IP Address: 10.0.1.44
Router ID: 10.0.1.44
Router Cap: 10.0.1.44
SRGB Range: 6000 SRGB Base SID: 18000 I:1 V:0
SR-Algorithm:
Algorithm: 0
Metric: 10 IS-Extended PE3.02
IPv4 Interface Address: 10.33.44.2
Neighbor IP Address: 10.33.44.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1033 LAN Adjacency SID: 25600 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IS-Extended PE4.03
IPv4 Interface Address: 10.44.2.1
Neighbor IP Address: 10.44.2.1
Maximum Link Bandwidth: 100m
Reservable Bandwidth: 100m
Unreserved Bandwidth:
Unreserved Bandwidth at priority 0: 100m
Unreserved Bandwidth at priority 1: 100m
Unreserved Bandwidth at priority 2: 100m
Unreserved Bandwidth at priority 3: 100m
Unreserved Bandwidth at priority 4: 100m
Unreserved Bandwidth at priority 5: 100m
Unreserved Bandwidth at priority 6: 100m
Unreserved Bandwidth at priority 7: 100m
TE-Default Metric: 10
System-ID: 0100.0000.1002 LAN Adjacency SID: 25601 F:0 B:0 V:1 L:1 S:0 P:0
Metric: 10 IP-Extended 10.0.1.44/32
Prefix-SID: index 600 R:0 N:1 P:1 E:0 V:0 L:0
Metric: 10 IP-Extended 10.33.44.0/30
Metric: 10 IP-Extended 10.44.2.0/30
Metric: 10 IP-Extended 10.1.36.0/24
Metric: 20 IP-Extended 10.0.1.33/32
Prefix-SID: index 500 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 20 IP-Extended 10.1.45.0/24
Metric: 20 IP-Extended 10.33.1.0/30
Metric: 30 IP-Extended 10.0.1.1/32
Prefix-SID: index 200 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 20 IP-Extended 10.0.1.2/32
Prefix-SID: index 300 R:1 N:0 P:1 E:0 V:0 L:0
Metric: 30 IP-Extended 10.0.1.11/32
Prefix-SID: index 100 R:1 N:0 P:0 E:0 V:0 L:0
Metric: 20 IP-Extended 10.1.2.0/30
Metric: 20 IP-Extended 10.1.24.0/24
Metric: 30 IP-Extended 10.11.1.0/30
Metric: 20 IP-Extended 10.11.2.0/30
PE4.03-00 0x0000000B 0xD92B 1132 0/0/0
Metric: 0 IS-Extended PE4.00
Metric: 0 IS-Extended P2.00
Validation 4
Verify that segment routing is enabled and that prefix SIDs are announced to other routers.
Verify that prefix SIDs are installed as labels in MPLS forwarding table. Verify the same in FTN and ILM tables.
P1#show mpls forwarding-table
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN
Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
i> 10.0.1.2/32 1 4 0 Yes LSP_DEFAULT 16800 eth1 No 10.1.2.2
i> 10.0.1.11/32 3 2 0 Yes LSP_DEFAULT 3 eth2 No 10.11.1.1
i> 10.0.1.33/32 2 1 0 Yes LSP_DEFAULT 3 eth4 No 10.33.1.1
i> 10.0.1.44/32 4 5 0 Yes LSP_DEFAULT 17100 eth1 No 10.1.2.2
In the forwarding tables above, the configured prefix SIDs are in the Out-Label column which is expected and is global across the topology. The swap happens in between nodes with this prefix SID and there is no local labelling.
Also verify the ILM and FTN tables.
P1#show mpls ilm-table
Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown
Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop LSP-Type
i> 10.33.1.1/32 18 24320 3 N/A eth4 10.33.1.1 LSP_DEFAULT
i> 10.0.1.2/32 21 17300 16800 N/A eth1 10.1.2.2 LSP_DEFAULT
i> 10.0.1.1/32 17 17200 Nolabel N/A N/A 127.0.0.1 LSP_DEFAULT
i> 10.0.1.11/32 23 17100 3 N/A eth2 10.11.1.1 LSP_DEFAULT
i> 10.0.1.33/32 22 17500 3 N/A eth4 10.33.1.1 LSP_DEFAULT
i> 10.0.1.44/32 24 17600 17100 N/A eth1 10.1.2.2 LSP_DEFAULT
i> 10.11.1.1/32 19 24321 3 N/A eth2 10.11.1.1 LSP_DEFAULT
i> 10.1.2.2/32 20 24322 3 N/A eth1 10.1.2.2 LSP_DEFAULT
P1#show mpls ftn-table
Primary FTN entry with FEC: 10.0.1.2/32, id: 1, row status: Active
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A
Matched bytes:0, pkts:0, TX bytes:0, Pushed pkts:0
Cross connect ix: 6, in intf: - in label: 0 out-segment ix: 4
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 4, owner: ISIS-SR, Stale: NO, out intf: eth1, out label: 16800
Nexthop addr: 10.1.2.2 cross connect ix: 6, op code: Push
Primary FTN entry with FEC: 10.0.1.11/32, id: 3, row status: Active
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A
Matched bytes:0, pkts:0, TX bytes:0, Pushed pkts:0
Cross connect ix: 3, in intf: - in label: 0 out-segment ix: 2
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 2, owner: N/A, Stale: NO, out intf: eth2, out label: 3
Nexthop addr: 10.11.1.1 cross connect ix: 3, op code: Push
Primary FTN entry with FEC: 10.0.1.33/32, id: 2, row status: Active
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A
Matched bytes:0, pkts:0, TX bytes:0, Pushed pkts:0
Cross connect ix: 1, in intf: - in label: 0 out-segment ix: 1
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 1, owner: N/A, Stale: NO, out intf: eth4, out label: 3
Nexthop addr: 10.33.1.1 cross connect ix: 1, op code: Push
Primary FTN entry with FEC: 10.0.1.44/32, id: 4, row status: Active
Owner: ISIS-SR, distance: 115, Action-type: Redirect to LSP, Exp-bits: 0x0, Incoming DSCP: none
Tunnel id: 0, Protected LSP id: 0, Description: N/A
Matched bytes:0, pkts:0, TX bytes:0, Pushed pkts:0
Cross connect ix: 7, in intf: - in label: 0 out-segment ix: 5
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 5, owner: ISIS-SR, Stale: NO, out intf: eth1, out label: 17100
Nexthop addr: 10.1.2.2 cross connect ix: 7, op code: Push
P1#show mpls in-segment-table
Owner: ISIS-SR, # of pops: 1, fec: 10.33.1.1/32, ILM-ID: 18
RX bytes:0, pkts:0, TX bytes:0, Swapped pkts:0, Popped pkts:0
Cross connect ix: 1, in intf: - in label: 24320 out-segment ix: 1
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 1, owner: N/A, Stale: NO, out intf: eth4, out label: 3
Nexthop addr: 10.33.1.1 cross connect ix: 1, op code: Swap
Owner: ISIS-SR, # of pops: 1, fec: 10.0.1.2/32, ILM-ID: 21
RX bytes:0, pkts:0, TX bytes:0, Swapped pkts:0, Popped pkts:0
Cross connect ix: 6, in intf: - in label: 17300 out-segment ix: 4
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 4, owner: ISIS-SR, Stale: NO, out intf: eth1, out label: 16800
Nexthop addr: 10.1.2.2 cross connect ix: 6, op code: Swap
Owner: ISIS-SR, # of pops: 1, fec: 10.0.1.1/32, ILM-ID: 17
RX bytes:0, pkts:0, TX bytes:0, Swapped pkts:0, Popped pkts:0
Cross connect ix: 1, in intf: - in label: 17200 out-segment ix: 0
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 0, owner: CLI, Stale: NO, out intf: N/A, out label: N/A
Nexthop addr: 127.0.0.1 cross connect ix: 1, op code: Pop
Owner: ISIS-SR, # of pops: 1, fec: 10.0.1.11/32, ILM-ID: 23
RX bytes:0, pkts:0, TX bytes:0, Swapped pkts:0, Popped pkts:0
Cross connect ix: 3, in intf: - in label: 17100 out-segment ix: 2
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 2, owner: N/A, Stale: NO, out intf: eth2, out label: 3
Nexthop addr: 10.11.1.1 cross connect ix: 3, op code: Swap
Owner: ISIS-SR, # of pops: 1, fec: 10.0.1.33/32, ILM-ID: 22
RX bytes:0, pkts:0, TX bytes:0, Swapped pkts:0, Popped pkts:0
Cross connect ix: 1, in intf: - in label: 17500 out-segment ix: 1
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 1, owner: N/A, Stale: NO, out intf: eth4, out label: 3
Nexthop addr: 10.33.1.1 cross connect ix: 1, op code: Swap
Owner: ISIS-SR, # of pops: 1, fec: 10.0.1.44/32, ILM-ID: 24
RX bytes:0, pkts:0, TX bytes:0, Swapped pkts:0, Popped pkts:0
Cross connect ix: 7, in intf: - in label: 17600 out-segment ix: 5
Owner: ISIS-SR, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 5, owner: ISIS-SR, Stale: NO, out intf: eth1, out label: 17100
Nexthop addr: 10.1.2.2 cross connect ix: 7, op code: Swap
Owner: ISIS-SR, # of pops: 1, fec: 10.11.1.1/32, ILM-ID: 19
RX bytes:0, pkts:0, TX bytes:0, Swapped pkts:0, Popped pkts:0
Cross connect ix: 3, in intf: - in label: 24321 out-segment ix: 2
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 2, owner: N/A, Stale: NO, out intf: eth2, out label: 3
Nexthop addr: 10.11.1.1 cross connect ix: 3, op code: Swap
Owner: ISIS-SR, # of pops: 1, fec: 10.1.2.2/32, ILM-ID: 20
RX bytes:0, pkts:0, TX bytes:0, Swapped pkts:0, Popped pkts:0
Cross connect ix: 5, in intf: - in label: 24322 out-segment ix: 3
Owner: N/A, Persistent: No, Admin Status: Up, Oper Status: Up
Out-segment with ix: 3, owner: N/A, Stale: NO, out intf: eth1, out label: 3
Nexthop addr: 10.1.2.2 cross connect ix: 5, op code: Swap
P1#show mpls out-segment-table
Out-segment with ix: 2, owner: N/A, Stale: NO, out intf: eth2, out label: 3
Nexthop addr: 10.11.1.1 cross connect ix: 3, op code: Push
TX bytes:0, pkts:0, error pkts:0, discard pkts:0
Out-segment with ix: 4, owner: ISIS-SR, Stale: NO, out intf: eth1, out label: 16800
Nexthop addr: 10.1.2.2 cross connect ix: 6, op code: Push
TX bytes:0, pkts:0, error pkts:0, discard pkts:0
Out-segment with ix: 3, owner: N/A, Stale: NO, out intf: eth1, out label: 3
Nexthop addr: 10.1.2.2 cross connect ix: 5, op code: Push
TX bytes:0, pkts:0, error pkts:0, discard pkts:0
Out-segment with ix: 5, owner: ISIS-SR, Stale: NO, out intf: eth1, out label: 17100
Nexthop addr: 10.1.2.2 cross connect ix: 7, op code: Push
TX bytes:0, pkts:0, error pkts:0, discard pkts:0
Out-segment with ix: 1, owner: N/A, Stale: NO, out intf: eth4, out label: 3
Nexthop addr: 10.33.1.1 cross connect ix: 1, op code: Push
TX bytes:0, pkts:0, error pkts:0, discard pkts:0
Segment Routing Ping and Traceroute
Segment Routing Ping
The MPLS LSP ping feature is used to check the connectivity between ingress and egress of LSP. MPLS LSP ping uses MPLS echo request and reply messages, similar to Internet Control Message Protocol (ICMP) echo request and reply messages, to validate an LSP.
Segment routing ping is an extension of the MPLS LSP ping to perform the connectivity verification on the segment routing control plane.
Segment Routing ping can use either generic FEC type or SR control-plane FEC type (ISIS-SR or OSPF-SR)
Segment Routing Trace
The MPLS LSP traceroute is used to isolate the failure point of an LSP. It is used for hop-by-hop fault locali-zation and path tracing. The MPLS LSP traceroute feature relies on the expiration of the Time to Live (TTL) value of the packet that carries the echo request.
Similar to segment routing ping, you can initiate the segment routing traceroute operation only when Segment Routing control plane is available at the originator
Segment Routing traceroute can use either generic FEC type or SR control-plane FEC type (OSPF-SR or ISIS-SR).
See Figure 2-2.
Validation
These examples show how to use segment routing ping to test the connectivity of a segment routing control plane and segment routing trace to trace LSP of specified Prefix SID.
Ping with other options.
Detail
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV, 'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched), 'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch, 'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed Type 'Ctrl+C' to abort
! seq_num = 1 10.33.1.1 2.41 ms
! seq_num = 2 10.33.1.1 1.06 ms
! seq_num = 3 10.33.1.1 1.11 ms
! seq_num = 4 10.33.1.1 1.67 ms
! seq_num = 5 10.33.1.1 1.07 ms
! seq_num = 2 10.33.1.1 1.06 ms
! seq_num = 3 10.33.1.1 1.11 ms
! seq_num = 4 10.33.1.1 1.67 ms
! seq_num = 5 10.33.1.1 1.07 ms
Success Rate is 100.00 percent (5/5) round-trip min/avg/max = 1.06/1.74/2.41
Destination
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 destination 127.1.0.1 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV, 'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched), 'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch, 'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed Type 'Ctrl+C' to abort
! seq_num = 1 10.33.1.1 1.60 ms
! seq_num = 2 10.33.1.1 1.22 ms
! seq_num = 3 10.33.1.1 1.37 ms
! seq_num = 4 10.33.1.1 1.38 ms
! seq_num = 5 10.33.1.1 1.52 ms
! seq_num = 2 10.33.1.1 1.22 ms
! seq_num = 3 10.33.1.1 1.37 ms
! seq_num = 4 10.33.1.1 1.38 ms
! seq_num = 5 10.33.1.1 1.52 ms
Success Rate is 100.00 percent (5/5) round-trip min/avg/max = 1.22/1.41/1.60
Source
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 destination 127.1.0.1 source 10.0.1.11 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV, 'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched), 'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch, 'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed Type 'Ctrl+C' to abort
! seq_num = 1 10.33.1.1 1.97 ms
! seq_num = 2 10.33.1.1 1.26 ms
! seq_num = 3 10.33.1.1 1.50 ms
! seq_num = 4 10.33.1.1 1.46 ms
! seq_num = 5 10.33.1.1 1.35 ms
! seq_num = 2 10.33.1.1 1.26 ms
! seq_num = 3 10.33.1.1 1.50 ms
! seq_num = 4 10.33.1.1 1.46 ms
! seq_num = 5 10.33.1.1 1.35 ms
Success Rate is 100.00 percent (5/5) round-trip min/avg/max = 1.26/1.62/1.97
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 ?
destination Destination
detail detailed output
flags Validate Fec
force-explicit-null Force Explicit NULL label
interval Interval
repeat Count
reply-mode Reply-mode
source source
timeout Timeout of ping
ttl Time-to-live
<cr>
destination Destination
detail detailed output
flags Validate Fec
force-explicit-null Force Explicit NULL label
interval Interval
repeat Count
reply-mode Reply-mode
source source
timeout Timeout of ping
ttl Time-to-live
<cr>
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 flags ?
destination Destination
detail detailed output
force-explicit-null Force Explicit NULL label
interval Interval
repeat Count
reply-mode Reply-mode
source source
timeout Timeout of ping
ttl Time-to-live
<cr>
destination Destination
detail detailed output
force-explicit-null Force Explicit NULL label
interval Interval
repeat Count
reply-mode Reply-mode
source source
timeout Timeout of ping
ttl Time-to-live
<cr>
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 flags de?
destination Destination
detail detailed output
destination Destination
detail detailed output
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 flags detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
! seq_num = 1 10.33.1.1 1.76 ms
! seq_num = 2 10.33.1.1 1.20 ms
! seq_num = 3 10.33.1.1 1.32 ms
! seq_num = 4 10.33.1.1 1.06 ms
! seq_num = 5 10.33.1.1 1.23 ms
! seq_num = 2 10.33.1.1 1.20 ms
! seq_num = 3 10.33.1.1 1.32 ms
! seq_num = 4 10.33.1.1 1.06 ms
! seq_num = 5 10.33.1.1 1.23 ms
Success Rate is 100.00 percent (5/5)
round-trip min/avg/max = 1.06/1.41/1.76
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 timeout 500 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 500 seconds
round-trip min/avg/max = 1.06/1.41/1.76
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 timeout 500 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 500 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
! seq_num = 1 10.33.1.1 2.12 ms
! seq_num = 2 10.33.1.1 1.41 ms
! seq_num = 3 10.33.1.1 1.55 ms
! seq_num = 4 10.33.1.1 1.60 ms
! seq_num = 5 10.33.1.1 1.37 ms
! seq_num = 2 10.33.1.1 1.41 ms
! seq_num = 3 10.33.1.1 1.55 ms
! seq_num = 4 10.33.1.1 1.60 ms
! seq_num = 5 10.33.1.1 1.37 ms
Success Rate is 100.00 percent (5/5)
round-trip min/avg/max = 1.37/1.75/2.12
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 repeat 10 detail
Sending 10 MPLS Echos to 10.0.1.33, timeout is 5 seconds
round-trip min/avg/max = 1.37/1.75/2.12
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 repeat 10 detail
Sending 10 MPLS Echos to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
! seq_num = 1 10.33.1.1 2.46 ms
! seq_num = 2 10.33.1.1 1.73 ms
! seq_num = 3 10.33.1.1 1.61 ms
! seq_num = 4 10.33.1.1 1.74 ms
! seq_num = 5 10.33.1.1 1.98 ms
! seq_num = 6 10.33.1.1 1.59 ms
! seq_num = 7 10.33.1.1 1.75 ms
! seq_num = 8 10.33.1.1 2.07 ms
! seq_num = 9 10.33.1.1 1.83 ms
! seq_num = 10 10.33.1.1 1.82 ms
! seq_num = 2 10.33.1.1 1.73 ms
! seq_num = 3 10.33.1.1 1.61 ms
! seq_num = 4 10.33.1.1 1.74 ms
! seq_num = 5 10.33.1.1 1.98 ms
! seq_num = 6 10.33.1.1 1.59 ms
! seq_num = 7 10.33.1.1 1.75 ms
! seq_num = 8 10.33.1.1 2.07 ms
! seq_num = 9 10.33.1.1 1.83 ms
! seq_num = 10 10.33.1.1 1.82 ms
Success Rate is 100.00 percent (10/10)
round-trip min/avg/max = 1.59/2.02/2.46
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 interval 10000 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
round-trip min/avg/max = 1.59/2.02/2.46
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 interval 10000 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
! seq_num = 1 10.33.1.1 1.81 ms
! seq_num = 2 10.33.1.1 2.02 ms
! seq_num = 3 10.33.1.1 1.90 ms
! seq_num = 4 10.33.1.1 1.83 ms
! seq_num = 5 10.33.1.1 6.84 ms
! seq_num = 2 10.33.1.1 2.02 ms
! seq_num = 3 10.33.1.1 1.90 ms
! seq_num = 4 10.33.1.1 1.83 ms
! seq_num = 5 10.33.1.1 6.84 ms
Success Rate is 100.00 percent (5/5)
round-trip min/avg/max = 1.81/4.32/6.84
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 ttl 225 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
round-trip min/avg/max = 1.81/4.32/6.84
PE1#ping mpls isis-sr ipv4 10.0.1.33/32 ttl 225 detail
Sending 5 MPLS Echos to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
! seq_num = 1 10.33.1.1 2.21 ms
! seq_num = 2 10.33.1.1 1.50 ms
! seq_num = 3 10.33.1.1 1.34 ms
! seq_num = 4 10.33.1.1 1.61 ms
! seq_num = 5 10.33.1.1 1.36 ms
! seq_num = 2 10.33.1.1 1.50 ms
! seq_num = 3 10.33.1.1 1.34 ms
! seq_num = 4 10.33.1.1 1.61 ms
! seq_num = 5 10.33.1.1 1.36 ms
Success Rate is 100.00 percent (5/5)
round-trip min/avg/max = 1.34/1.78/2.21
round-trip min/avg/max = 1.34/1.78/2.21
=======================
TRACEROUTE
=======================
PE1#trace mpls isis-sr ipv4 10.0.1.33/32 detail
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
TRACEROUTE
=======================
PE1#trace mpls isis-sr ipv4 10.0.1.33/32 detail
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
0 10.11.1.1 [Labels: 17500]
R 1 10.11.1.2 [Labels: ] 2.00 ms
! 2 10.33.1.1 2.31 ms
R 1 10.11.1.2 [Labels: ] 2.00 ms
! 2 10.33.1.1 2.31 ms
PE1#trace mpls isis-sr ipv4 10.0.1.33/32 destination 127.1.0.1 detail
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
0 10.11.1.1 [Labels: 17500]
R 1 10.11.1.2 [Labels: ] 1.22 ms
! 2 10.33.1.1 1.61 ms
R 1 10.11.1.2 [Labels: ] 1.22 ms
! 2 10.33.1.1 1.61 ms
PE1#trace mpls isis-sr ipv4 10.0.1.33/32 destination 127.1.0.1 source 10.0.1.11 detail
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
0 10.11.1.1 [Labels: 17500]
R 1 10.11.1.2 [Labels: ] 1.26 ms
! 2 10.33.1.1 1.74 ms
R 1 10.11.1.2 [Labels: ] 1.26 ms
! 2 10.33.1.1 1.74 ms
PE1#trace mpls isis-sr ipv4 10.0.1.33/32 flags detail
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
0 10.11.1.1 [Labels: 17500]
R 1 10.11.1.2 [Labels: ] 0.98 ms
! 2 10.33.1.1 1.35 ms
R 1 10.11.1.2 [Labels: ] 0.98 ms
! 2 10.33.1.1 1.35 ms
PE1#trace mpls isis-sr ipv4 10.0.1.33/32 reply-mode 2 detail
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
0 10.11.1.1 [Labels: 17500]
R 1 10.11.1.2 [Labels: ] 1.34 ms
! 2 10.33.1.1 1.87 ms
R 1 10.11.1.2 [Labels: ] 1.34 ms
! 2 10.33.1.1 1.87 ms
PE1#trace mpls isis-sr ipv4 10.0.1.33/32 repeat 10 detail
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
0 10.11.1.1 [Labels: 17500]
R 1 10.11.1.2 [Labels: ] 1.22 ms
! 2 10.33.1.1 1.73 ms
R 1 10.11.1.2 [Labels: ] 1.22 ms
! 2 10.33.1.1 1.73 ms
PE1#trace mpls isis-sr ipv4 10.0.1.33/32 interval 1000 detail
Tracing MPLS Label Switched Path to 10.0.1.33, timeout is 5 seconds
Codes:
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
'!' - Success, 'Q' - request not sent, '.' - timeout,
'x' - Retcode 0, 'M' - Malformed Request, 'm' - Errored TLV,
'N' - LBL Mapping Err, 'D' - DS Mismatch,
'U' - Unknown Interface, 'R' - Transit (LBL Switched),
'B' - IP Forwarded, 'F' No FEC Found, 'f' - FEC Mismatch,
'P' - Protocol Error, 'X' - Unknown code,
'Z' - Reverse FEC Validation Failed
Type 'Ctrl+C' to abort
0 10.11.1.1 [Labels: 17500]
R 1 10.11.1.2 [Labels: ] 1.04 ms
! 2 10.33.1.1 1.83 ms
R 1 10.11.1.2 [Labels: ] 1.04 ms
! 2 10.33.1.1 1.83 ms