OcNOS SP : Layer 3 Guide : Border Gateway Protocol Command Reference : BGP Flowspec Commands
BGP Flowspec Commands
This chapter contains the BGP Flowspec commands.
• drop
• vrf
address-family
Specify address-family type to attach a policy to a specific address-family. This command enters address family configuration mode.
Command Syntax
address-family ipv4
no address-family
Parameters
None
Command Mode
Flowspec mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#flowspec
(config-flowspec)#address-family ipv4
address-family ipv4 flowspec vrf
This command is to enter address-family ipv4 flowspec vrf mode to configure IPv4 BGP Flowspec specific parameters in a VRF.
Command Syntax
address-family ipv4 flowspec vrf VRF_NAME
no address-famlily ipv4 flowspec vrf VRF_NAME
Parameters
VRF_NAME
vrf name
Command Mode
Config router mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config-router)#address-family ipv4 flowspec vrf VRF1
 
class-map type traffic match-all
Define a traffic class and associate rules by using match sub-commands, after the class-map type traffic command is typed in. The created c class-map can be removed with No form of this command. Only match-all criteria (match all match items configured in a class-map) is supported in BGP Flowspec.
Command Syntax
class-map type traffic match-all CLASS_MAP_NAME
no class-map type traffic CLASS_MAP_NAME
Parameters
CLASS_MAP_NAME
a class-map-name to define.
Command Mode
Configure mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
drop
When an attached class-map is matched, the matched packet drops.
Command Syntax
drop
no drop
Parameters
None
Command Mode
policy-map class mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config-pmap-pbr-c)#drop
flowspec
This command is executed in the global configuration, and enter default VRF mode.
Command Syntax
flowspec
no flowspec
Parameters
None
Command Mode
Configure mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#flowspec
hardware filter ipv4-bgp-flowspec
Use this command to enable ipv4 BGP flowspec feature in hardware. Unless it is enabled, the all flowspec routes are not set to hardware, while the all BGP operations are done not related to this command.
Command Syntax
hardware filter ipv4-bgp-flowspec enable
hardware filter ipv4-bgp-flowspec disable
Parameters
None
Command Mode
Configure mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#hardware-profile filter ipv4-bgp-flowspec enable
 
local-install
Specify whether or not, the attached service policy is installed to a local node. By default, not installed. This command can be taken effect for all address-families by specifying it before entering address-family configuration mode, or for a specific address-family when the mode is address-family configuration.
Command Syntax
local-install interface-all
no local-install
Parameters
None
Command Mode
Flowspec, flowspec address family and flowspec-vrfmode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
config)#flowspec
(config-flowspec)#local-install interface-all
(config-flowspec)#address-family ipv4
(config-flowspec-af)#local-install interface-all
(config-flowspec-af)#exit
(config-flowspec)#vrf VRF1
(config-flowspec-vrf)#local-install interface-all
 
 
match dscp
Use this command to match DSCP value.
Command Syntax
match dscp [DSCP_VALUE|DSCP_VALUE_RANGE][,...,[DSCP_VALUE|DSCP_VALUE_RANGE]]
no match dscp
Parameters
DSCP_CODE_VALUE
 
A class-map-name to define.
DSCP_CODE_VALUE_RANGE
 
A range in a form of range: MIN_VALU-MAX_VALUE. e.g. 10-3e
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match dscp 1c
match destination-address
IP destination address to match. It can be specified with prefix and netmask bits.
Command Syntax
match destination-address ipv4 A.B.C.D/M
no match destination-address
Parameters
A.B.C.D/M
A.B.C.D is prefix and M is netmask bits.
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match destination-address ipv4 1.1.1.1/32
 
match destination-port
Use this command to match TCP/UDP destination port number(s).
Command Syntax
match destination_port [PORT_NUMBER|PORT_RANGE][,...,[PORT_NUMBER|PORT_RANGE]]
no match destination_port
Parameters
PORT_NUMBER
A port number in 1-65535
PORT_NUMBER_RANGE
 
A range in a form of range: MIN_VALUE-MAX_VALUE. e.g. 10-100
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
match fragment-type
Use this command to match fragment type.
Command Syntax
match fragment-type FRAGMENT_TYPE
no match fragment-type
Parameters
FRAGMENT_TYPE
lf: Last fragment
ff: First fragment
isf: Is s fragment other than the first
df: Don't fragment
lf-ff-isf: When one of lf, ff, and isf is true to match, it matches.
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match fragment-type lf
 
match icmp-code
Use this command to match the ICMP code.
Command Syntax
match ipv4 icmp-code [ICMP_TYPE_VALUE|ICMP_TYPE_VALUE_RANGE] [,...,[ICMP_TYPE_VALUE|ICMP_TYPE_VALUE_RANGE]]
no match ipv4 icmp-code
Parameters
ICMP_CODE_VALUE
 
ICMP code number in 0-255
ICMP_CODE_VALUE_RANGE
 
A range in a form of range: MIN_VALU-MAX_VALUE. e.g. 10-100
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match ipv4 icmp-type 10
(config-cmap-tr)#match ipv4 icmp-code 20
 
match icmp-type
Use this command to match TCP/UDP destination port number(s).
Command Syntax
match ipv4 icmp-type [ICMP_TYPE_VALUE|ICMP_TYPE_VALUE_RANGE] [,...,[ICMP_TYPE_VALUE|ICMP_TYPE_VALUE_RANGE]]
no match ipv4 icmp-type
Parameters
ICMP_TYPE_VALUE
 
ICMP code number in 0-255
ICMP_TYPE_VALUE_RANGE
 
A range in a form of range: MIN_VALU-MAX_VALUE. e.g. 10-100
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match ipv4 icmp-type 10
match packet-length
Use this command to match packet length.
Command Syntax
match packet-length [PACKET_LENGTH_VALUE|PACKET_LENGTH_VALUE_RANGE]
[,...,[PACKET_LENGTH_VALUE|PACKET_LENGTH_VALUE_RANGE]]
no match packet-length
Parameters
PACKET_LENGTH_VALUE
 
ICMP code number in 0-255
PACKET_LENGTH_VALUE_RANGE
 
A range in a form of range: MIN_VALU-MAX_VALUE. e.g. 10-100
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match packet-length 70-100
match port
Use this command to match TCP/UDP port number(s).
Command Syntax
match port [PORT_NUMBER|PORT_RANGE][,...,[PORT_NUMBER|PORT_RANGE]]
no match port
Parameters
PORT_NUMBER
A port number in 1-65535
PORT_NUMBER_RANGE
 
A range in a form of range: MIN_VALUE-MAX_VALUE. e.g. 10-100
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match port 1000-2000
 
 
 
 
match protocol
Use this command to match Protocol number(s).
Command Syntax
match protocol [IP_PROTOCOL_NUM|IP_PROTOCOL_NUMBER_RANGE][,...,[IP_PRTOCOL_NUMBER|IP_PROTOCOL_NUMBER_RANGE]]
no match protocol
Parameters
IP_PRTOCOL_NUMBER
 
IP protocol number in 0-255
IP_PROTOCOL_NUMBER_RANGE
 
A range in a form of range: MIN_VALUE-MAX_VALUE. e.g. 10-100
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match protocol 122
 
 
 
 
 
 
 
 
match source-address
IP source address to match. It can be specified with prefix and netmask bits.
Command Syntax
match source-address ipv4 A.B.C.D/M
no match source-address
Parameters
A.B.C.D/M
A.B.C.D is prefix and M is netmask bits.
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match source-address ipv4 2.2.2.2/32
 
 
 
match source-port
Use the command to match TCP/UDP source port number(s).
Command Syntax
match source_port [PORT_NUMBER|PORT_RANGE][,...,[PORT_NUMBER|PORT_RANGE]]
no match source_port
Parameters
PORT_NUMBER
A port number in 1-65535
PORT_NUMBER_RANGE
 
A range in a form of range: MIN_VALU-MAX_VALUE. e.g. 10-100
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
 
match tcp-flag
Use the command to match TCP flag.
Command Syntax
match ipv4 tcp-flag TCP_FLAG_VALUE bitmask TCP_FLAG_BITMASK
no match ipv4 tcp-flag bitmask
Parameters
TCP_FLAG_VALUE
 
TCP flag value in hexadecimal (0-fff)
TCP_FLAG_BITMASK
 
TCP flag bitmask in hexadecimal (0-fff)
Command Mode
Class-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#class-map type traffic match-all test1
(config-cmap-tr)#match tcp-flag 2e bit-mask 3f
neighbor flowspec-vaildation-disable
The following parameters can be configured with neighbor command in address-family for BGP Flowspec. The flowspec-vaildation-disable is a parameter for BGP Flowspec. When it is specified, BGP Flowspec validation is disabled. By default, this parameter is enabled.
Command Syntax
neighbor A.B.C.D flowspec-vaildation-disable
Parameters
A.B.C.D
IPv4 address
Command Mode
Router address family mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config-router)#address-family ipv4 flowspec
(config-router-af)#neighbor 1.1.1.1 flowspec-validation-disable
 
policy-map
Create or modify a policy map with a pbr type that can be attached as a service policy, and proceed to a mode to enter class command after this command is typed in. Multiple class-map can be linked to a created policy-map. To delete a policy-map, use the no form of this command.
Command Syntax
policy-map type pbr POLICY_MAP_NAME
no policy-map type pbr POLICY_MAP_NAME
Parameters
POLICY_MAP_NAME
 
A name for a creating modifying policy-map.
Command Mode
Configure mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#policy-map type pbr
(config)#policy-map type pbr test2
police rate
Use this command to set a rate applied for matched packets.
Command Syntax
police rate RATE_VALUE [pps|bps]
no police rate
Parameters
RATE_VALUE
rate value specified in 1-1000000000.
pps
A unit for RATE_VALUE: pps mean packets per second.
bps
A unit for RATE_VALUE: bps mean bit per second.
Command Mode
Policy-map class mode
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
7017(config-pmap-pbr-c)#police rate
7017(config-pmap-pbr-c)#police rate 100000000 bps
policy-map class type traffic
Attach a class to a policy-map created by policy-map command. This command enters policy-map mode.
Command Syntax
class type traffic CLASS_MAP_NAME
no class type traffic CLASS_MAP_NAME
Parameters
CLASS_MAP_NAME
 
A name for class-map already created with class-map command.
Command Mode
Policy-map mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#policy-map type pbr test2
(config-pmap-pbr)#class type traffic test1
 
 
redirect
Set a VRF redirected to for matched packets.
Command Syntax
redirect ipv4 extcommunity rt ROUTE_TARGET
no redirect ipv4 extcommunity rt
Parameters
ROUTE_TARGET
Specify a route target, Two formats can be used:
AS number:index, e.g. 100:10
IPv4 address: index, e.g. 2.2.2.2:10.
Command Mode
policy-map class mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config-pmap-pbr-c)#redirect ipv4 extcommunity rt 100:10
set dscp
Set a DSCP value to a matched packet to mark with it.
Command Syntax
set dscp DSCP_VALUE
no set dscp
Parameters
DSCP_VALUE
DSCP value in hexadecimal (0-3f)
Command Mode
policy-map class mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config-pmap-pbr-c)#set dscp 3f
service-policy type pbr
Attach/detach a service policy to BGP component. The attached policy is locally installed optionally by typing local-install command, as well as a BGP Flowspec route is injected to a BGP component.
Command Syntax
service-policy type pbr POLICY_MAP_NAME
no service-policy type pbr POLICY_MAP_NAME
Parameters
POLICY_MAP_NAME
 
Name of the policy map.
Command Mode
Flowspec address family mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
(config)#flowspec
(config-flowspec)#local-install interface-all
(config-flowspec)#address-family ipv4
(config-flowspec-af)#service-policy type pbr test1
show ip bgp
Use these commands to show the output.
Command Syntax
show ip bgp flowspec
show ip bgp flowspec summary (vrf (VRFNAME|all|default))
show ip bgp (ipv4|vpnv4) flowspec (detail|)
show ip bgp (ipv4|vpnv4) flowspec (vrf (VRFNAME|all|default)) (detail|)
show ip bgp vpnv4 flowspec rd WORD (detail|)
Parameters
None
Command Mode
Executive mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
#show ip bgp flowspec
BGP router identifier 19.19.19.19, local AS number 100
BGP table version is 7
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd
1.1.1.1 4 100 40 35 7 0 0 00:04:51 1
 
Total number of neighbors 1
 
Total number of Established sessions 1
BGP router identifier 4.4.4.4, local AS number 100
BGP VRF VRF1 Route Distinguisher: 100:10
BGP table version is 1
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd
200.2.1.2 4 65530 0 0 0 0 0 never Connect
 
Total number of neighbors 1
 
Total number of Established sessions 0
 
show ip bgp flowspec summary vrf VRF1
BGP router identifier 4.4.4.4, local AS number 100
BGP VRF VRF1 Route Distinguisher: 100:10
BGP table version is 1
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd
200.2.1.2 4 65530 0 0 0 0 0 never Idle
 
Total number of neighbors 1
 
Total number of Established sessions 0
 
#show ip bgp flowspec summary vrf all
BGP router identifier 4.4.4.4, local AS number 100
BGP VRF VRF1 Route Distinguisher: 100:10
BGP table version is 1
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd
200.2.1.2 4 65530 0 0 0 0 0 never Connect
 
Total number of neighbors 1
 
Total number of Established sessions 0
BGP router identifier 19.19.19.19, local AS number 100
BGP table version is 7
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd
1.1.1.1 4 100 41 37 7 0 0 00:05:31 1
 
Total number of neighbors 1
 
Total number of Established sessions 1
 
#show ip bgp flowspec summary vrf default
BGP router identifier 19.19.19.19, local AS number 100
BGP table version is 7
1 BGP AS-PATH entries
0 BGP community entries
 
Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd
1.1.1.1 4 100 42 37 7 0 0 00:05:37 1
 
Total number of neighbors 1
 
Total number of Established sessions 1
 
#show ip bgp ipv4 flowspec
detail summary vrf
#show ip bgp ipv4 flowspec vrf all
BGP table version is 1, local router ID is 4.4.4.4
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal,
l - labeled, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
 
Network Next Hop Metric LocPrf Weight Path
 
BGP Route Table for VRF VRF1
*>i flowspec/368 1.1.1.1 0 100 0 i
 
Total number of prefixes 1
*>i flowspec/368 1.1.1.1 0 100 0 i
 
Total number of prefixes 1
 
#show ip bgp ipv4 flowspec vrf all detail
BGP table version is 1, local router ID is 4.4.4.4
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal,
l - labeled, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
 
Network Next Hop Metric LocPrf Weight Path
 
BGP Route Table for VRF VRF1
*>i flowspec/368 1.1.1.1 0 100 0 i
 
FlowSpec:
destination ip address: 1.1.1.1/32
source ip address: 2.2.2.2/32
IP protocol:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:122
TCP/UDP port:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:1000
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:2000
ICMP type:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:10
ICMP code:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:20
TCP flags:
e:0 a:0 len:0 not:0 m:1 data:0x2e
e:1 a:1 len:0 not:1 m:0 data:0x11
Packet length:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:70
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:100
DSCP:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:0x1c
fragment:
e:1 a:0 len:0 not:0 m:1 data:0x8
 
FlowSpec Actions:
traffic_rate: 100000000 bps
rt_redirect: as_type: as 100:10 vrf_id:2 fib_id:2
 
 
Total number of prefixes 1
*>i flowspec/368 1.1.1.1 0 100 0 i
 
FlowSpec:
destination ip address: 1.1.1.1/32
source ip address: 2.2.2.2/32
IP protocol:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:122
TCP/UDP port:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:1000
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:2000
ICMP type:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:10
ICMP code:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:20
TCP flags:
e:0 a:0 len:0 not:0 m:1 data:0x2e
e:1 a:1 len:0 not:1 m:0 data:0x11
Packet length:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:70
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:100
DSCP:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:0x1c
fragment:
e:1 a:0 len:0 not:0 m:1 data:0x8
 
FlowSpec Actions:
traffic_rate: 0 pps
 
 
Total number of prefixes 1
 
#show ip bgp vpnv4 flowspec vrf VRF1
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal, l - labeled
S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
 
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 100:10 (Default for VRF VRF1)
*>i flowspec/368 1.1.1.1 0 100 0 i
Announced routes count = 0
Accepted routes count = 1
#show ip bgp vpnv4 flowspec vrf VRF1 detail
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal, l - labeled
S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
 
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 100:10 (Default for VRF VRF1)
*>i flowspec/368 1.1.1.1 0 100 0 i
 
FlowSpec:
destination ip address: 1.1.1.1/32
source ip address: 2.2.2.2/32
IP protocol:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:122
TCP/UDP port:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:1000
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:2000
ICMP type:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:10
ICMP code:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:20
TCP flags:
e:0 a:0 len:0 not:0 m:1 data:0x2e
e:1 a:1 len:0 not:1 m:0 data:0x11
Packet length:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:70
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:100
DSCP:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:0x1c
fragment:
e:1 a:0 len:0 not:0 m:1 data:0x8
 
FlowSpec Actions:
traffic_rate: 100000000 bps
rt_redirect: as_type: as 100:10 vrf_id:2 fib_id:2
 
Announced routes count = 0
Accepted routes count = 1
 
#show ip bgp vpnv4 flowspec rd 100:10
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal, l - labeled
S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
 
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 100:10 (Default for VRF VRF1)
*>i flowspec/368 1.1.1.1 0 100 0 i
Announced routes count = 0
Accepted routes count = 1
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal, l - labeled
S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
 
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 100:10
*>i flowspec/368 1.1.1.1 0 100 0 i
Announced routes count = 0
Accepted routes count = 1
 
#show ip bgp vpnv4 flowspec rd 100:10 detail
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal, l - labeled
S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
 
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 100:10 (Default for VRF VRF1)
*>i flowspec/368 1.1.1.1 0 100 0 i
 
FlowSpec:
destination ip address: 1.1.1.1/32
source ip address: 2.2.2.2/32
IP protocol:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:122
TCP/UDP port:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:1000
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:2000
ICMP type:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:10
ICMP code:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:20
TCP flags:
e:0 a:0 len:0 not:0 m:1 data:0x2e
e:1 a:1 len:0 not:1 m:0 data:0x11
Packet length:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:70
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:100
DSCP:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:0x1c
fragment:
e:1 a:0 len:0 not:0 m:1 data:0x8
 
FlowSpec Actions:
traffic_rate: 100000000 bps
rt_redirect: as_type: as 100:10 vrf_id:2 fib_id:2
 
Announced routes count = 0
Accepted routes count = 1
Status codes: s suppressed, d damped, h history, a add-path, * valid, > best, i - internal, l - labeled
S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
 
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 100:10
*>i flowspec/368 1.1.1.1 0 100 0 i
 
FlowSpec:
destination ip address: 1.1.1.1/32
source ip address: 2.2.2.2/32
IP protocol:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:122
TCP/UDP port:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:1000
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:2000
ICMP type:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:10
ICMP code:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:20
TCP flags:
e:0 a:0 len:0 not:0 m:1 data:0x2e
e:1 a:1 len:0 not:1 m:0 data:0x11
Packet length:
e:0 a:0 len:1 lt:0 gt:1 eq:1 data:70
e:1 a:1 len:1 lt:1 gt:0 eq:1 data:100
DSCP:
e:1 a:0 len:0 lt:0 gt:0 eq:1 data:0x1c
fragment:
e:1 a:0 len:0 not:0 m:1 data:0x8
 
FlowSpec Actions:
traffic_rate: 100000000 bps
rt_redirect: as_type: as 100:10 vrf_id:2 fib_id:2
 
Announced routes count = 0
Accepted routes count = 1
 
vrf
Specify a VRF to configure service policies. This command is executed in the default vrf mode, and enter vrf mode. address-family, local-install and service-policy commands can be executed in the same way (stated in address-family, locall-install, and service-policy type pbr) executed in the default vrf mode.
Command Syntax
vrf VRF_NAME
no vrf VRF_NAME
Parameters
VRF_NAME
A vrf name already created
Command Mode
Flowspec mode.
Applicability
This command was introduced in OcNOS version 6.3.0.
Examples
7017(config)#flowspec
7017(config-flowspec)#vrf VRF1