OcNOS SP : System Management Guide : QSFP-DD Command Reference : QSFP-DD Commands
QSFP-DD Commands
This chapter is a reference for the QSFP-DD configuration and status commands:
• ha
• hw
• la
• lw
• prbs
application
Use this command to select the application ID to be configured for this QSFP-DD module.
Use the no parameter with this command to remove this configuration. If no application is configured then application ID 1 will be selected as per module default.
Note: Only 400G application modes are supported.
Note: For checking the supported applications modes show qsfp-dd <port no.> advertisement applications command, see the example.
Example:
OcNOS#show qsfp-dd 49 application
 
Port Number : 49
-----------------------------------
User Config | H/W Config
-----------------------------------
Application 2 | Application 2
 
OcNOS#sh qsfp-dd 49 advertisement applications
 
Port Number : 49
> Application 1:
| Host |
Interface : 400GAUI-8 C2M
Application BR : 425.00
Lane Count : 8
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2.000000
Lane Assigned : Lane-1
| Media |
Interface : 400ZR, DWDM, Amplified
Application BR : 478.75
Lane Count : 1
Lane Sig BR : 59.84375
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8.000000
Lane Assigned : Lane-1
Application 2:
| Host |
Interface : 400GAUI-8 C2M
Application BR : 425.00
Lane Count : 8
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2.000000
Lane Assigned : Lane-1
| Media |
Interface : 400ZR, Single Wavelen., Unamp.
Application BR : 478.75
Lane Count : 1
Lane Sig BR : 59.84375
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8.000000
Lane Assigned : Lane-1
Application 3:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2.000000
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : 400ZR, DWDM, Amplified
Application BR : 478.75
Lane Count : 1
Lane Sig BR : 59.84375
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8.000000
Lane Assigned : Lane-1
Application 4:
| Host |
Interface : 400GAUI-8 C2M
Application BR : 425.00
Lane Count : 8
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2.000000
Lane Assigned : Lane-1
| Media |
Interface : ZR400-OFEC-16QAM
Application BR : 481.108374
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8.000000
Lane Assigned : Lane-1
Application 5:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2.000000
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : ZR400-OFEC-16QAM
Application BR : 481.108374
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8.000000
Lane Assigned : Lane-1
Application 6:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2.000000
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : ZR300-OFEC-8QAM
Application BR : 360.831281
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-8QAM
Bits Per Unit Intvl : 6.000000
Lane Assigned : Lane-1
Application 7:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2.000000
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : ZR200-OFEC-QPSK
Application BR : 240.554187
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-QPSK
Bits Per Unit Intvl : 4.000000
Lane Assigned : Lane-1
Application 8:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2.000000
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : ZR100-OFEC-QPSK
Application BR : 120.277094
Lane Count : 1
Lane Sig BR : 30.069273
Modulation Format : DP-QPSK
Bits Per Unit Intvl : 4.000000
Lane Assigned : Lane-1
Command Syntax
application <2-15>
Parameters
<2-15>
Configurable application IDs
Command Mode
QSFP-DD mode
Default
By default, application ID 1 is selected.
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#application 8
(config-qsfp-dd)#commit
(config-qsfp-dd)#no application
(config-qsfp-dd)#commit
(config-qsfp-dd)#
 
laser channel
Use this command to configure the laser channel number for the QSFP-DD module.
Command Syntax
laser channel NUMBER
no laser channel
Parameters
NUMBER
channel number
Default
None.
Command Mode
QSFP-DD mode
Applicability
This command was introduced in OcNOS version 6.2.0.
Examples
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#laser channel 10
(config-qsfp-dd)#commit
(config-qsfp-dd)#no laser channel
(config-qsfp-dd)#commit
(config-qsfp-dd)#
laser grid
Use this command to configure the laser grid spacing frequency for the QSFP-DD module.
Command Syntax
laser grid (3p125|6p25|12p5|25|33|50|75|100)
no laser grid
Parameters
3p125
3.125 GHz
6p25
6.25 GHz
12p5
12.5 GHz
25
25 GHz
33
33 GHz
50
50 GHz
75
75 GHz
100
100 GHz
Default
None.
Command Mode
QSFP-DD mode
Applicability
This command was introduced in OcNOS version 6.2.0.
Examples
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#laser grid 50
(config-qsfp-dd)#commit
(config-qsfp-dd)#no laser grid
(config-qsfp-dd)#commit
(config-qsfp-dd)#
laser fine-tune-freq
Use this command to configure the laser fine tune frequency offset for the QSFP-DD module.
Command Syntax
laser fine-tune-freq VALUE
no laser fine-tune-freq
Parameters
VALUE
Fine tune frequency offset in GHz
Default
None.
Command Mode
QSFP-DD mode
Applicability
This command was introduced in OcNOS version 6.2.0.
Examples
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#laser fine-tune-freq 1.5
(config-qsfp-dd)#commit
(config-qsfp-dd)#no laser fine-tune-freq
(config-qsfp-dd)#commit
(config-qsfp-dd)#
laser output-power
Use this command to configure the laser target output power for the QSFP-DD module.
Command Syntax
laser output-power VALUE
no laser output-power
Parameters
VALUE
Laser target output power
Default
None.
Command Mode
QSFP-DD mode
Applicability
This command was introduced in OcNOS version 6.2.0.
Examples
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#laser output-power -9.2
(config-qsfp-dd)#commit
(config-qsfp-dd)#no laser output-power
(config-qsfp-dd)#commit
(config-qsfp-dd)#
loopback
Use this command to configure the loopback type (input, output, both) on the QSFP-DD module host/media side. If the loopback type is supported by the QSFP-DD module this will enable the loopback function.
Use the no parameter to remove this configuration and disable the loopback function.
Command Syntax
loopback (in|out|both) (host|media)
no loopback (host|media)
Parameters
in
Configure input loopback
out
Configure output looback
both
Configure input and output loopback
host
Configure host side
media
Configure media side
Command Mode
QSFP-DD mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
(config)#qsfp-dd 0
(config-qsfp-dd)#loopback in host
(config-qsfp-dd)#loopback out media
(config-qsfp-dd)#commit
(config-qsfp-dd)#loopback both media
(config-qsfp-dd)#no loopback host
(config-qsfp-dd)#commit
(config-qsfp-dd)#
 
prbs
Use these commands to configure the PRBS pattern generator/checker type to be used for diagnostics of the QSFP-DD module host/media side and to configure the PRBS pattern generator/checker location (pre-fec/post-fec) on the QSFP-DD module host/media side. If the generator/checker pattern type and location are supported by the QSFP-DD module this will enable the selected function.
Use the no parameter to remove this configuration and disable the generator/checker function.
Command Syntax
prbs (generator|checker) type (31q|31|23q|23|15q|15|13q|13|9q|9|7q|7|ssprq) (host|media)
prbs (generator|checker) (pre-fec|post-fec) (host|media)
no prbs (generator|checker) type (host|media)
no prbs (generator|checker) (host|media)
Parameters
generator
Configure the pattern generator
checker
Configure the pattern checker
31q
Configure PRBS-31Q type
31
Configure PRBS-31 type
23q
Configure PRBS-23Q type
23
Configure PRBS-23 type
15q
Configure PRBS-15Q type
15
Configure PRBS-15 type
13q
Configure PRBS-13Q type
13
Configure PRBS-13 type
9q
Configure PRBS-9Q type
9
Configure PRBS-9 type
7q
Configure PRBS-7q type
7
Configure PRBS-7 type
ssprq
Configure SSPRQ type
pre-fec
Configure to generate before the FEC encoder / check before the FEC decoder
post-fec
Configure to generate after the FEC encoder / check after the FEC decoder
host
Configure host side
media
Configure media side
Command Mode
QSFP-DD mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#prbs generator type 15 host
(config-qsfp-dd)#prbs checker type 23q host
(config-qsfp-dd)#prbs generator type 7q media
(config-qsfp-dd)#prbs checker type ssprq media
(config-qsfp-dd)#commit
(config-qsfp-dd)#no prbs generator type host
(config-qsfp-dd)#no prbs checker type media
(config-qsfp-dd)#commit
(config-qsfp-dd)#
qsfp-dd
Use this command to select a QSFP-DD port to configure and enter the qsfp-dd command mode. Use the exit command to quit from this mode.
Command Syntax
qsfp-dd PORTNUM
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Configure mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#
 
rx-output eq-pre-cursor-target
Use this command to configure the Rx output equalizer pre-cursor target override value.
Use the no form of this command to remove the Rx output equalizer pre-cursor target override value.
Command Syntax
rx-output eq-pre-cursor-target <1-15>
no rx-output eq-pre-cursor-target
Parameters
<1-15>
Output equalizer pre-cursor target value
Default
None.
Command Mode
QSFP-DD and QSFP-DD host-lane modes
Applicability
This command was introduced before OcNOS version 6.5.1.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#rx-output eq-pre-cursor-target 4
(config-qsfp-dd)#commit
(config-qsfp-dd)#no rx-output eq-pre-cursor-target
(config-qsfp-dd)#commit
(config-qsfp-dd)#host-lane 2
(config-qsfp-dd-host)#rx-output eq-pre-cursor-target 1
(config-qsfp-dd-host)#commit
(config-qsfp-dd-host)#no rx-output eq-pre-cursor-target
(config-qsfp-dd-host)#commit
 
rx-output eq-post-cursor-target
Use this command to configure the Rx output equalizer post-cursor target override value.
Use the no form of this command to remove the Rx output equalizer post-cursor target override value..
Command Syntax
rx-output eq-post-cursor-target <1-15>
no rx-output eq-post-cursor-target
Parameters
<1-15>
Output equalizer post-cursor target value
Default
None.
Command Mode
QSFP-DD and QSFP-DD host-lane modes
Applicability
This command was introduced before OcNOS version 6.5.1.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#rx-output eq-post-cursor-target 2
(config-qsfp-dd)#commit
(config-qsfp-dd)#no rx-output eq-post-cursor-target
(config-qsfp-dd)#commit
(config-qsfp-dd)#host-lane 7
(config-qsfp-dd-host)#rx-output eq-post-cursor-target 6
(config-qsfp-dd-host)#commit
(config-qsfp-dd-host)#no rx-output eq-post-cursor-target
(config-qsfp-dd-host)#commit
rx-output amp-target
Use this command to configure the Rx output amplitude target override value.
Use the no form of this command to remove the Rx output amplitude target override value.
Command Syntax
rx-output amp-target <0-15>
no rx-output amp-target
Parameters
<1-15>
Output amplitude target value
Default
None.
Command Mode
QSFP-DD and QSFP-DD host-lane modes
Applicability
This command was introduced before OcNOS version 6.5.1.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#rx-output amp-target 0
(config-qsfp-dd)#commit
(config-qsfp-dd)#no rx-output amp-target
(config-qsfp-dd)#commit
(config-qsfp-dd)#host-lane 3
(config-qsfp-dd-host)#rx-output amp-target 1
(config-qsfp-dd-host)#commit
(config-qsfp-dd-host)#no rx-output amp-target
(config-qsfp-dd-host)#commit
 
rx cdr-bypass
Use this command to enable the Rx CDR bypass.
Use the no form of this command to disable the Rx CDR bypass.
Command Syntax
rx cdr-bypass
no rx cdr-bypass
Parameters
None
Command Mode
QSFP-DD and QSFP-DD host-lane modes
Applicability
This command was introduced before OcNOS version 6.5.1.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#rx cdr-bypass
(config-qsfp-dd)#commit
(config-qsfp-dd)#no rx cdr-bypass
(config-qsfp-dd)#commit
(config-qsfp-dd)#host-lane 2
(config-qsfp-dd-host)#rx cdr-bypass
(config-qsfp-dd-host)#commit
(config-qsfp-dd-host)#no rx cdr-bypass
 
show qsfp-dd advertisement applications
Use this command to show QSFP-DD module advertised applications.
Command Syntax
show qsfp-dd PORTNUM advertisement applications
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 advertisement applications
 
Port Number : 0
> Application 1:
| Host |
Interface : 400GAUI-8 C2M
Application BR : 425.00
Lane Count : 8
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-1
| Media |
Interface : 400ZR, DWDM, Amplified
Application BR : 478.75
Lane Count : 1
Lane Sig BR : 59.84375
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8
Lane Assigned : Lane-1
Application 2:
| Host |
Interface : 400GAUI-8 C2M
Application BR : 425.00
Lane Count : 8
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-1
| Media |
Interface : 400ZR, Single Wavelen., Unamp.
Application BR : 478.75
Lane Count : 1
Lane Sig BR : 59.84375
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8
Lane Assigned : Lane-1
Application 3:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : 400ZR, DWDM, Amplified
Application BR : 478.75
Lane Count : 1
Lane Sig BR : 59.84375
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8
Lane Assigned : Lane-1
Application 4:
| Host |
Interface : 400GAUI-8 C2M
Application BR : 425.00
Lane Count : 8
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-1
| Media |
Interface : 400ZRP, DWDM, amplified 120Km
Application BR : 481.108374
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8
Lane Assigned : Lane-1
Application 5:
| Host |
Interface : 400GAUI-8 C2M
Application BR : 425.00
Lane Count : 8
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-1
| Media |
Interface : 400ZRP, DWDM, Amplified 450Km
Application BR : 481.108374
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8
Lane Assigned : Lane-1
Application 6:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : 400ZRP, DWDM, Amplified 450Km
Application BR : 481.108374
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8
Lane Assigned : Lane-1
Application 7:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : 100ZRP, DWDM, Amplified 600Km
Application BR : 360.831281
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-8QAM
Bits Per Unit Intvl : 6
Lane Assigned : Lane-1
Application 8:
| Host |
Interface : 400GAUI-8 C2M
Application BR : 425.00
Lane Count : 8
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-1
| Media |
Interface : 400ZRP, DWDM, amplified 450Km (Enhanced Constellation)
Application BR : 481.108374
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8
Lane Assigned : Lane-1
Application 9:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : 400ZRP, DWDM, amplified 450Km (Enhanced Constellation)
Application BR : 481.108374
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-16QAM
Bits Per Unit Intvl : 8
Lane Assigned : Lane-1
Application 10:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : 100ZRP, DWDM, amplified 600Km (Enhanced Constellation)
Application BR : 360.831281
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-8QAM
Bits Per Unit Intvl : 6
Lane Assigned : Lane-1
Application 11:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : 100ZRP, DWDM, Amplified 1000Km
Application BR : 240.554187
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-QPSK
Bits Per Unit Intvl : 4
Lane Assigned : Lane-1
Application 12:
| Host |
Interface : CAUI-4 C2M without FEC
Application BR : 103.13
Lane Count : 4
Lane Sig BR : 25.78125
Modulation Format : NRZ
Bits Per Unit Intvl : 1
Lane Assigned : Lane-5/Lane-1
| Media |
Interface : 100ZRP, DWDM, Amplified 1000Km
Application BR : 240.554187
Lane Count : 1
Lane Sig BR : 60.1385468
Modulation Format : DP-QPSK
Bits Per Unit Intvl : 4
Lane Assigned : Lane-1
Application 13:
| Host |
Interface : 100GAUI-2 C2M
Application BR : 106.25
Lane Count : 2
Lane Sig BR : 26.5625
Modulation Format : PAM4
Bits Per Unit Intvl : 2
Lane Assigned : Lane-7/Lane-5/Lane-3/Lane-1
| Media |
Interface : 100ZRP, DWDM, amplified 2000Km
Application BR : 120.277094
Lane Count : 1
Lane Sig BR : 30.069273
Modulation Format : DP-QPSK
Bits Per Unit Intvl : 4
Lane Assigned : Lane-1
Application 14:
| Host |
Interface : CAUI-4 C2M without FEC
Application BR : 103.13
Lane Count : 4
Lane Sig BR : 25.78125
Modulation Format : NRZ
Bits Per Unit Intvl : 1
Lane Assigned : Lane-5/Lane-1
| Media |
Interface : 100ZRP, DWDM, amplified 2000Km
Application BR : 120.277094
Lane Count : 1
Lane Sig BR : 30.069273
Modulation Format : DP-QPSK
Bits Per Unit Intvl : 4
Lane Assigned : Lane-1
 
show qsfp-dd advertisement controls
Use this command to show QSFP-DD module advertised controls.
Command Syntax
show qsfp-dd PORTNUM advertisement controls
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 advertisement controls
 
Port Number : 0
Wavelength Control : Yes
Tunable Transmitter : Yes
Tx Output Squelching : Not Supported
Forced Tx Output Squelching : No
Tx Output Squelching Disable : No
Tx Output Disable : Yes
Input Polarity Flip Tx : Yes
Rx Output Squelching Disable : Yes
Rx Output Disable : Yes
Output Polarity Flip Rx : Yes
 
show qsfp-dd advertisement diagnostics host
Use this command to show QSFP-DD module advertised host side diagnostics.
Command Syntax
show qsfp-dd PORTNUM advertisement diagnostics host
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
 
show qsfp-dd 0 advertisement diagnostics host
 
Port Number : 0
| Supported Loopback Modes |
Output : Yes
Input : Yes
Per Lane : Yes
| Reporting Capabilities |
Input SNR : No
FEC : Yes
| PRBS Checker |
Post FEC : Yes
Pre FEC : Yes
Types : PRBS-31Q, PRBS-31, PRBS-23Q, PRBS-23, PRBS-15Q, PRBS-15, PRBS-13Q, PRBS-13, PRBS-9Q, PRBS-9, PRBS-7Q, PRBS-7
| PRBS Generator |
Post FEC : Yes
Pre FEC : Yes
Types : PRBS-31Q, PRBS-31, PRBS-23Q, PRBS-23, PRBS-15Q, PRBS-15, PRBS-13Q, PRBS-13, PRBS-9Q, PRBS-9, PRBS-7Q, PRBS-7
 
show qsfp-dd advertisement diagnostics media
Use this command to show QSFP-DD module advertised media side diagnostics.
Command Syntax
show qsfp-dd PORTNUM advertisement diagnostics media
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
 
show qsfp-dd 0 advertisement diagnostics media
 
Port Number : 0
| Supported Loopback Modes |
Output : Yes
Input : No
Per Lane : Yes
| Reporting Capabilities |
Input SNR : Yes
FEC : Yes
| PRBS Checker |
Post FEC : Yes
Pre FEC : No
Types : PRBS-31, PRBS-23, PRBS-15, PRBS-7
| PRBS Generator |
Post FEC : Yes
Pre FEC : Yes
Types : PRBS-31, PRBS-23, PRBS-15, PRBS-7
 
show qsfp-dd advertisement diagnostics module
Use this command to show QSFP-DD module advertised diagnostics.
Command Syntax
show qsfp-dd PORTNUM advertisement diagnostics module
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
 
show qsfp-dd 0 advertisement diagnostics module
 
Port Number : 0
| Supported Loopback Modes |
Simul. Host & Media Side : Yes
| Reporting Capabilities |
Bit Error Ratio : Yes
Bits & Errors Counting : Yes
show qsfp-dd advertisement durations
Use this command to show module advertised durations
Command Syntax
show qsfp-dd PORTNUM advertisement durations
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 advertisement durations
 
Port Number : 0
ModSel Wait : 4 us
DP Init Max : 10 s <= t < 1 min
DP Deinit Max : 1 s <= t < 5 s
DP Tx Turn On Max : 50 ms <= t < 100 ms
DP Tx Turn Off Max : 1 ms <= t < 5 ms
Module Power Up Max : 10 s <= t < 1 min
Module Power Down Max : 1 s <= t < 5 s
show qsfp-dd advertisement laser
Use this command to show QSFP-DD module advertised laser controls.
Command Syntax
show qsfp-dd PORTNUM advertisement laser
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
 
show qsfp-dd 0 advertisement laser
 
Port Number : 0
Supported Grids : 6.25 GHz, 12.5 GHz, 25 GHz, 50 GHz, 100 GHz, 75 GHz
6.25 GHz Channels : Low=191.275 THz, High=196.125 THz, Total=776
12.5 GHz Channels : Low=191.275 THz, High=196.125 THz, Total=388
25 GHz Channels : Low=191.275 THz, High=196.125 THz, Total=194
50 GHz Channels : Low=191.300 THz, High=196.100 THz, Total=96
100 GHz Channels : Low=191.300 THz, High=196.100 THz, Total=48
75 GHz Channels : Low=191.300 THz, High=196.100 THz, Total=64
Fine Tuning Support : Yes
Fine Tuning Resolution : 0.001 GHz
Fine Tuning Low Offset : -6.000 GHz
Fine Tuning High Offset : 6.000 GHz
Output Power Programmable Per Lane : Yes
Min Output Power Programmable : -22.90 dBm
Max Output Power Programmable : 4.00 dBm
 
show qsfp-dd advertisement monitors host
Use this command to show QSFP-DD module advertised host side monitors.
Command Syntax
show qsfp-dd PORTNUM advertisement monitors host
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 advertisement monitors host
 
Port Number : 0
Pre-FEC BER Minimum Input : Yes [Lane 1, Lane 3, Lane 5, Lane 7]
Pre-FEC BER Maximum Input : Yes [Lane 1, Lane 3, Lane 5, Lane 7]
Pre-FEC BER Average Input : Yes [Lane 1, Lane 3, Lane 5, Lane 7]
Pre-FEC BER Current Value Input : Yes [Lane 1, Lane 3, Lane 5, Lane 7]
FERC Minimum Input : Yes [Lane 1, Lane 3, Lane 5, Lane 7]
FERC Maximum Input : Yes [Lane 1, Lane 3, Lane 5, Lane 7]
FERC Average Input : Yes [Lane 1, Lane 3, Lane 5, Lane 7]
FERC Current Value Input : Yes [Lane 1, Lane 3, Lane 5, Lane 7]
 
| Link Performance |
Tx FDD : Yes
Tx FED : Yes
 
show qsfp-dd advertisement monitors media
Use this command to show QSFP-DD module advertised media side monitors.
Command Syntax
show qsfp-dd PORTNUM advertisement monitors media
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 advertisement monitors media
 
Port Number : 0
Rx Optical Power : Yes
Tx Optical Power : Yes
Tx Bias : Yes
Rx Los : Yes
Tx Failure : Yes
Rx CDR LOL : Yes
Laser Age : Yes [Lane 1]
Pre-FEC BER Minimum Input : Yes [Lane 1]
Pre-FEC BER Maximum Input : Yes [Lane 1]
Pre-FEC BER Average Input : Yes [Lane 1]
Pre-FEC BER Current Value Input : Yes [Lane 1]
FERC Minimum Input : Yes [Lane 1]
FERC Maximum Input : Yes [Lane 1]
FERC Average Input : Yes [Lane 1]
FERC Current Value Input : Yes [Lane 1]
Modular Bias X/I : Yes [Lane 1]
Modular Bias X/Q : Yes [Lane 1]
Modular Bias Y/I : Yes [Lane 1]
Modular Bias Y/Q : Yes [Lane 1]
Modular Bias X_Phase : Yes [Lane 1]
Modular Bias Y_Phase : Yes [Lane 1]
CD - high granularity, short link : Yes [Lane 1]
CD - low granularity, long link : Yes [Lane 1]
DGD : Yes [Lane 1]
SOPMD - high granularity : Yes [Lane 1]
PDL : Yes [Lane 1]
OSRN : Yes [Lane 1]
eSRN : Yes [Lane 1]
CFO : Yes [Lane 1]
Tx Power : Yes [Lane 1]
Rx Total Power : Yes [Lane 1]
Rx Signal Power : Yes [Lane 1]
SOP ROC : Yes [Lane 1]
SOPMD - low granularity : Yes [Lane 1]
 
| FEC Performance |
Rx Bits : Yes
Rx Correct Bits : Yes
Rx Frames : Yes
Rx Uncorrect Frames : Yes
 
| Link Performance |
Rx DSP CCD : Yes
Rx DSP DGD : Yes
Rx SOPM : Yes
Rx PDL : Yes
Rx oSNR : Yes
Rx eSNR : Yes
Rx CFO : Yes
Rx EvmModem : No
Tx Power : Yes
Rx Input Optical Power : Yes
Rx input Optical Signal Power : Yes
Rx SOPCR : Yes
Rx SOPMD Low Granularity : No
Rx Clock Recovery Monitor : No
Rx FDD : Yes
Rx FEC : Yes
show qsfp-dd advertisement monitors module
Use this command to show QSFP-DD module advertised monitors
Command Syntax
show qsfp-dd PORTNUM advertisement monitors module
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 advertisement monitors module
 
Port Number : 0
Voltage : Yes
Temperature : Yes
TEC Current : Yes
Laser Temperature : Yes
Laser Temperature [2] : No
 
Rx Power : Yes
Rx Signal Power : Yes
show qsfp-dd advertisement pages
Use this command to show QSFP-DD module advertised supported pages.
Command Syntax
show qsfp-dd PORTNUM advertisement pages
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 application
 
Port Number : 0
-----------------------------------
User Config | H/W Config
-----------------------------------
None | Application 1
OcNOS>show qsfp-dd 0 advertisement pages
 
Port Number : 0
Network Path : No
VDM : Yes
VDM Support : Groups 1-2 (Page 20h-21h, 24h-25h, 28h-29h, first 1/2 of 2Ch, 2Dh)
Diagnostics : Yes
User(Page 03h) : Yes
Banks(Page 10h-1Fh) : Bank 0 (8 Lanes)
show qsfp-dd advertisement si
Use this command to display which signal integrity configuration capabilities the transceiver supports.
Command Syntax
show qsfp-dd <port> advertisement si
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.5.1.
Example
#show qsfp-dd 0 advertisement si
 
-------------------------------------------------
Codes
-------------------------------------------------
Tx Equalization > 1 - 12 : 1dB - 12db
13 - 15 : Vendor Specific
-------------------------------------------------
Rx Pre-Cursor Eq > 1 - 7 : 0.5 - 3.5dB
8 - 10 : Reserved
11 - 15 : Vendor Specific
-------------------------------------------------
Rx Post-Cursor Eq > 1 - 7 : 1 - 7dB
8 - 10 : Reserved
11 - 15 : Vendor Specific
-------------------------------------------------
Rx Amplitude > 0 : 100-400mV (P-P)
1 : 300-600mV (P-P)
2 : 400-800mV (P-P)
3 : 600-1200mV (P-P)
4 - 15 : Reserved
-------------------------------------------------
Port Number : 0
 
Manual Tx Input Eq. : No
 
Rx Output Eq. Type : P-P with constant amplitude/NA/Unknown
 
Rx Output Amplitude : No
 
Rx Output Eq. : Pre and post-cursor
Rx Output Eq. Pre-Cursor Max : Code 7(3.5dB)
Rx Output Eq. Post-Cursor Max : Code 7(7dB)
 
Tx CDR Supported : Yes
Tx CDR Bypass Supported : No
 
Rx CDR Supported : Yes
Rx CDR Bypass Supported : No
show qsfp-dd si status
Use this command to display what is the current signal integrity configuration status. It displays what is the current user configuration and what are the values programmed in the transceiver hardware.
Command Syntax
show qsfp-dd <port> si status
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.5.1.
Example
#show qsfp-dd 0 si status
 
Port Number : 0
 
--------------------------------------------------------
Parameter | Lane | User Config | H/W Config |
--------------------------------------------------------
Rx Pre-Cursor Eq | 1 | None | 11 |
| 2 | None | 11 |
| 3 | None | 11 |
| 4 | None | 11 |
| 5 | None | 11 |
| 6 | None | 11 |
| 7 | None | 11 |
| 8 | None | 11 |
--------------------------------------------------------
Rx Post-Cursor Eq | 1 | None | 11 |
| 2 | None | 11 |
| 3 | None | 11 |
| 4 | None | 11 |
| 5 | None | 11 |
| 6 | None | 11 |
| 7 | None | 11 |
| 8 | None | 11 |
--------------------------------------------------------
Tx CDR Bypass | 1 | None | Disabled |
| 2 | None | Disabled |
| 3 | None | Disabled |
| 4 | None | Disabled |
| 5 | None | Disabled |
| 6 | None | Disabled |
| 7 | None | Disabled |
| 8 | None | Disabled |
--------------------------------------------------------
Rx CDR Bypass | 1 | None | Disabled |
| 2 | None | Disabled |
| 3 | None | Disabled |
| 4 | None | Disabled |
| 5 | None | Disabled |
| 6 | None | Disabled |
| 7 | None | Disabled |
| 8 | None | Disabled |
--------------------------------------------------------
 
show qsfp-dd application
Use this command to show QSFP-DD module current selected application.
Command Syntax
show qsfp-dd PORTNUM application
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 application
 
Port Number : 0
-----------------------------------
User Config | H/W Config
-----------------------------------
None | Application 1
 
show qsfp-dd diagnostics host
Use this command to show QSFP-DD module host side diagnostics information.
Command Syntax
show qsfp-dd PORTNUM diagnostics host
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 diagnostics host
 
Port Number : 0
----------------------------------------------------
Attribute | Lane | Value |
----------------------------------------------------
Bit Error Ratio | 1 | 0.00e+00 |
| 2 | 0.00e+00 |
| 3 | 0.00e+00 |
| 4 | 0.00e+00 |
| 5 | 0.00e+00 |
| 6 | 0.00e+00 |
| 7 | 0.00e+00 |
| 8 | 0.00e+00 |
Bit Error Ratio(G) | 1 | 0.00e+00 |
| 2 | 0.00e+00 |
| 3 | 0.00e+00 |
| 4 | 0.00e+00 |
| 5 | 0.00e+00 |
| 6 | 0.00e+00 |
| 7 | 0.00e+00 |
| 8 | 0.00e+00 |
Error Count | 1 | 0 |
| 2 | 0 |
| 3 | 0 |
| 4 | 0 |
| 5 | 0 |
| 6 | 0 |
| 7 | 0 |
| 8 | 0 |
Bit Count | 1 | 0 |
| 2 | 0 |
| 3 | 0 |
| 4 | 0 |
| 5 | 0 |
| 6 | 0 |
| 7 | 0 |
| 8 | 0 |
Error Count(G) | 1 | 0 |
| 2 | 0 |
| 3 | 0 |
| 4 | 0 |
| 5 | 0 |
| 6 | 0 |
| 7 | 0 |
| 8 | 0 |
Bit Count(G) | 1 | 0 |
| 2 | 0 |
| 3 | 0 |
| 4 | 0 |
| 5 | 0 |
| 6 | 0 |
| 7 | 0 |
| 8 | 0 |
 
show qsfp-dd diagnostics media
Use this command to show QSFP-DD module media side diagnostics information.
Command Syntax
show qsfp-dd PORTNUM diagnostics media
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 diagnostics media
 
Port Number : 0
----------------------------------------------------
Attribute | Lane | Value |
----------------------------------------------------
Signal To Noise Ratio | 1 | 0.00 |
Bit Error Ratio | 1 | 0.00e+00 |
Bit Error Ratio(G) | 1 | 0.00e+00 |
Error Count | 1 | 0 |
Bit Count | 1 | 0 |
Error Count(G) | 1 | 0 |
Bit Count(G) | 1 | 0 |
show qsfp-dd eeprom
Use this command to show QSFP-DD module EEPROM information.
Command Syntax
show qsfp-dd PORTNUM eeprom
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 eeprom
 
Port Number : 0
Identifier : QSFP-DD Double Density 8X Pluggable Transceiver
Name : SmartOptics
OUI : 0x0 0x53 0x4f
Part No : SO-TQSFPDD4CCZRP
Revision Level : A
Serial_Number : 214156190
Manufacturing Date : 220318 (yymmddvv, v=vendor specific)
Module Power Class : 8
Module Max Power : 23.75 Watt
Cooling Implemented : Yes
Module Temperature Max : 80 Celsius
Module Temperature Min : 0 Celsius
Operating Voltage Min : 3.12 Volt
Optical Detector : PIN
Rx Power Measurement : Average Power
Tx Disable Module Wide : No
Cable Assembly Link Length : Separable Media
Connector Type : LC (Lucent Connector)
Media Interface Technology : 1550 nm DFB
CMIS Revision : 4.1
Memory Model : Paged
MCI Max Speed : 1000 kHz
Active Firmware Revision : 61.20
Inactive Firmware Revision : 61.20
Hardware Revision : 49.48
Media Type : Optical SMF
Max SMF Link Length : 630.0 Kilometer
Wavelength Nominal : 1547.70 nm
Wavelength Tolerance : 166.55 nm
show qsfp-dd laser grid
Use this command to show QSFP-DD module laser grid spacing information for frequencies of 3.125, 6.25 12.5 25, 33, 50, 75 and 100 GHz.
Command Syntax
show qsfp-dd PORTNUM laser grid (3p125|6p25|12p5|25|33|50|75|100)
Parameters
PORTNUM
QSFP-DD front panel port number
3p125
3.125 GHz
6p25
6.25 GHz
12p5
12.5 GHz
25
25 GHz
33
33 GHz
50
50 GHz
75
75 GHz
100
100 GHz
Default
None.
Command Mode
Exec mode and Privileged Exec mode.
Applicability
This command was introduced in OcNOS version 6.2.0.
Examples
show qsfp-dd 0 laser grid 100
 
Port Number : 0
 
------------------------------------------------------
Channel Number Frequency (THz) Wavelength (nm)
------------------------------------------------------
-18 191.300000 1567.133
-17 191.400000 1566.314
-16 191.500000 1565.496
-15 191.600000 1564.679
-14 191.700000 1563.863
-13 191.800000 1563.047
-12 191.900000 1562.233
-11 192.000000 1561.419
-10 192.100000 1560.606
-9 192.200000 1559.794
-8 192.300000 1558.983
-7 192.400000 1558.173
-6 192.500000 1557.363
-5 192.600000 1556.555
-4 192.700000 1555.747
-3 192.800000 1554.940
-2 192.900000 1554.134
-1 193.000000 1553.329
0 193.100000 1552.524
1 193.200000 1551.721
2 193.300000 1550.918
3 193.400000 1550.116
4 193.500000 1549.315
5 193.600000 1548.515
6 193.700000 1547.715
7 193.800000 1546.917
8 193.900000 1546.119
9 194.000000 1545.322
10 194.100000 1544.526
11 194.200000 1543.730
12 194.300000 1542.936
13 194.400000 1542.142
14 194.500000 1541.349
15 194.600000 1540.557
16 194.700000 1539.766
17 194.800000 1538.976
18 194.900000 1538.186
19 195.000000 1537.397
20 195.100000 1536.609
21 195.200000 1535.822
22 195.300000 1535.036
23 195.400000 1534.250
24 195.500000 1533.465
25 195.600000 1532.681
26 195.700000 1531.898
27 195.800000 1531.116
28 195.900000 1530.334
29 196.000000 1529.553
30 196.100000 1528.773
 
show qsfp-dd laser status
Use this command to show QSFP-DD module current laser configuration status and alarm flags.
Command Syntax
show qsfp-dd PORTNUM laser status
Parameters
PORTNUM
QSFP-DD front panel port number
Default
None.
Command Mode
Exec mode and Privileged Exec mode.
Applicability
This command was introduced in OcNOS version 6.2.0.
Examples
show qsfp-dd 0 laser status
 
Port Number : 0
 
--------------------------------------------------
Attribute | Lane | Value | Unit |
--------------------------------------------------
Grid Spacing | 1 | 100.000 | GHz |
Laser Frequency | 1 | 191.900000 | THz |
Channel Number | 1 | -12 | -- |
Wavelength | 1 | 1562.23 | nm |
 
-------------------------------------
Flag | Lane | Status |
-------------------------------------
Tuning in progress | 1 | No |
Wavelength locked | 1 | Yes |
 
-----------------------------------------------
Flag | Lane | Status (L) |
-----------------------------------------------
Target output power OOR | 1 | No |
Fine tuning out of range | 1 | No |
Tuning accepted | 1 | Yes |
Channel number valid | 1 | Yes |
show qsfp-dd monitors host
Use this command to show QSFP-DD module host side monitors information.
Command Syntax
show qsfp-dd PORTNUM monitors host
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 monitors host
 
Alarm Codes: FDD - FEC Detected Degrade, FED - FEC Excessive Degrade
LD - Local Degrade, RD - Remote Degrade
FLOPB - Flexe Loss of Pad Block, FLOMF - Flexe Loss of Multi-Frame
FLOF - Flexe Loss of Frame, FIIDM - Flexe Instance Id Mismatch
FCM - Flexe Calendar Mismatch, FIMM - Flexe Instance Map Mismatch
FGIDM - Flexe GID Mismatch, TLF - Transmit Local Fault
TRF - Transmit Remote Fault, TLOA - Transmit Loss of Alignment
RLF - Receive Local Fault, RRF - Receive Remote Fault
RLOA - Receive Loss of Alignment
 
Port Number : 0
-------------------------------------------------
Flag | Lane | Status (L) |
-------------------------------------------------
Tx LOS | 1 | False |
| 2 | False |
| 3 | False |
| 4 | False |
| 5 | False |
| 6 | False |
| 7 | False |
| 8 | False |
Tx CDR LOL | 1 | False |
| 2 | False |
| 3 | False |
| 4 | False |
| 5 | False |
| 6 | False |
| 7 | False |
| 8 | False |
Tx Adaptive Input Eq | 1 | Good |
| 2 | Good |
| 3 | Good |
| 4 | Good |
| 5 | Good |
| 6 | Good |
| 7 | Good |
| 8 | Good |
 
 
---------------------------------------------------------------------------------
Host Performance
---------------------------------------------------------------------------------
Attribute | Lane | Value |
---------------------------------------------------------------------------------
Alarm Status | 1 | LD |
---------------------------------------------------------------------------------
 
-----------------------------------------------
FEC Performance
-----------------------------------------------
Attribute | Lane | Value |
-----------------------------------------------
Tx Bits | 1 | 2125037470720 |
Tx Corrected Bits | 1 | 0 |
Tx Frames | 1 | 390631888 |
Tx Uncorrected Frames | 1 | 0 |
 
show qsfp-dd monitors media
Use this command to show QSFP-DD module media side monitors information.
Command Syntax
show qsfp-dd PORTNUM monitors media
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
 
show qsfp-dd 0 monitors media
 
Alarm Codes: TFIFO - Tx FIFO Error, TLOLDS - Tx Deskew Loss of Lock
TLOLRC - Tx Reference Clock Loss of Lock, TLOLCMU - Tx CMU Loss of Lock
TOOA - Tx Out of Alignment, TLOA - Tx Loss of Alignment
RFIFO - Rx FIFO Error, RLOLDS - Tx Deskew Loss of Lock
ROOA - Rx Out of Alignment, RLOA - Rx Loss of Alignment
RLOLCD - Rx Chromatic Dispersion Compensation Loss of Lock
RLOLD - Tx Demodulator Loss of Lock, RLOM - Rx Loss of Multi Frame
RLOF - Rx Loss of Frame, FDD - FEC Detected Degrade
FED - FEC Excessive Degrade, RPF - Remote Phy Fault
LD - Local Degrade, RD - Remote Degrade
 
Codes: [HA : High Alarm], [LA : Low Alarm], [HW : High Warning], [LW : Low Warning]
 
Port Number : 0
----------------------------------------------------------------------------------------------------------------
Monitors | Lane | Value | High Alarm | High Warning | Low Warning | Low Alarm | Unit |
----------------------------------------------------------------------------------------------------------------
Rx Optical Power | 1 | -18.9 | 2.0 | 0.0 | -23.0 | -28.2 | dBm |
Tx Optical Power | 1 | -7.8 | 0.0 | -2.0 | -16.0 | -18.0 | dBm |
Tx Bias | 1 | 287.3 | 0.0 | 0.0 | 0.0 | 0.0 | mA |
 
-------------------------------------------------
Flag | Lane | Status (L) |
-------------------------------------------------
Rx LOS | 1 | False |
Tx Failure | 1 | False |
Rx CDR LOL | 1 | False |
 
---------------------------------------------------------------------------------
Link Performance
---------------------------------------------------------------------------------
Attribute | Lane | Average | Minimum | Maximum | Unit |
---------------------------------------------------------------------------------
Rx DSP CCD | 1 | -1 | -1 | -1 | ps/nm |
Rx DSP DGD | 1 | 1.00 | 1.00 | 1.00 | ps |
Rx SOPMD | 1 | 40.00 | 40.00 | 40.00 | ps^2 |
Rx PDL | 1 | 0.5 | 0.5 | 0.5 | dB |
Rx OSNR | 1 | 36.4 | 36.4 | 36.4 | dB |
Rx ESNR | 1 | 16.4 | 16.4 | 16.4 | dB |
Rx CFO | 1 | 86 | 14 | 158 | MHz |
Tx Power | 1 | -7.77 | -7.78 | -7.76 | dBm |
Rx Input Optical Power | 1 | -18.90 | -18.91 | -18.90 | dBm |
Rx Input Optical Signal Power | 1 | -19.18 | -19.19 | -19.18 | dBm |
Rx SOPCR | 1 | 0 | 0 | 0 | krads/s |
Rx MER | 1 | 0.0 | 0.0 | 0.0 | dB |
---------------------------------------------------------------------------------
Alarm Status | 1 | RLOLCD, RLOLD, RPF |
---------------------------------------------------------------------------------
 
-----------------------------------------------
FEC Performance
-----------------------------------------------
Attribute | Lane | Value |
-----------------------------------------------
Rx Bits | 1 | 462238792192 |
Rx Corrected Bits | 1 | 1398045784 |
Rx Frames | 1 | 902810141 |
Rx Uncorrected Frames | 1 | 0 |
show qsfp-dd monitors module
Use this command to show QSFP-DD module monitors information.
Command Syntax
show qsfp-dd PORTNUM monitors module
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
 
show qsfp-dd 0 monitors module
 
Codes: [HA : High Alarm], [LA : Low Alarm], [HW : High Warning], [LW : Low Warning]
 
Port Number : 0
----------------------------------------------------------------------------------------------------------------
Attribute | Value | High Alarm | High Warning | Low Warning | Low Alarm | Units
----------------------------------------------------------------------------------------------------------------
Voltage | 3.24 | 3.46 | 3.43 | 3.17 | 3.13 | Volt
Temperature | 42.0 | 80.0 | 75.0 | 15.0 | -5.0 | Celsius
TEC Current Magnitude | 63.000 | 100.00 | 100.00 | -100.00 | -100.00 | %
Laser Temperature | 43.000 | 80.00 | 75.00 | -40.00 | -80.00 | Celsius
show qsfp-dd state
Use this command to show QSFP-DD module current state information.
Command Syntax
show qsfp-dd PORTNUM state
Parameters
PORTNUM
QSFP-DD front panel port number
Command Mode
Exec mode and Privileged Exec mode
Applicability
This command was introduced before OcNOS version 6.1.0.
Example
show qsfp-dd 0 state
 
Port Number : 0
Module Fault State : No fault
Module State : Ready
Data Path State : Activated [Starting On : Lane-1]
 
tx-input eq-target
Use this command to configure the Tx input equalizer target override value.
Use the no form of this command to remove the Tx input equalizer target override value.
Command Syntax
tx-input eq-target <1-15>
no tx-input eq-target
Parameters
<1-15>
Input equalizer target value
Default
None.
Command Mode
QSFP-DD and QSFP-DD host-lane modes
Applicability
This command was introduced before OcNOS version 6.5.1.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#tx-input eq-target 1
(config-qsfp-dd)#commit
(config-qsfp-dd)#no tx-input eq-target
(config-qsfp-dd)#commit
(config-qsfp-dd)#host-lane 3
(config-qsfp-dd-host)#tx-input eq-target 5
(config-qsfp-dd-host)#commit
(config-qsfp-dd-host)#no tx-input eq-target
(config-qsfp-dd-host)#commit
tx cdr-bypass
Use this command to enable the Tx CDR bypass.
Use the no form of this command to disable the Tx CDR bypass.
Command Syntax
tx cdr-bypass
no tx cdr-bypass
Parameters
None
Command Mode
QSFP-DD and QSFP-DD host-lane modes
Applicability
This command was introduced before OcNOS version 6.5.1.
Example
#configure terminal
(config)#qsfp-dd 0
(config-qsfp-dd)#tx cdr-bypass
(config-qsfp-dd)#commit
(config-qsfp-dd)#no tx cdr-bypass
(config-qsfp-dd)#commit
(config-qsfp-dd)#host-lane 2
(config-qsfp-dd-host)#tx cdr-bypass
(config-qsfp-dd-host)#commit
(config-qsfp-dd-host)#no tx cdr-bypass
(config-qsfp-dd-host)#commit